• 한국초전도ㆍ저온공학회논문지
• /
• 제13권1호
• /
• pp.51-55
• /
• 2011

In this study, the liquid-vapor (L-V) separator equipped with liquid-level meter is developed. In the developed L-V separator, the flange is designed to be attachable so that the separator can be flexibly applied under any cases where the volumetric of L-V separator is varied by the system requirement. The leak-tightness between the attachable flange and the chamber is experimentally confirmed with the use of double groove indium wire sealing even under the high pressure up to 20 bar. In addition, the liquid-level meter is designed and fabricated to figure out the inner state of L-V separator. It consists with 19 carbon composition resistors in series. All resistors are separately calibrated in the temperature range from 77 K to 200 K. The performance of the L-V separator and the liquid-level meter is investigated with experimental tests, and the result is presented in this paper.

• 환경생물
• /
• 제37권3호
• /
• pp.396-405
• /
• 2019

A new species of free-living marine nematode is described from intertidal sediments of the East Sea, Korea. Phanoderma koreense sp. nov. is characterized by the presence of well-developed pharyngeal and cephalic capsule, six inner labial sensilla present as minute papillae around with circular groove, long and slender spicules with 4-5 serrated distal end, located at the base of the precloacal supplement, a series of eight to nine stout and short setae on the ventral cloacal region and conico-cylindrical tail with two pairs of blunt setae. In this study, we provide taxonomic descriptions and illustrations of a new species by differential interference contrast microscope and a pictorial key to the valid species of Phanoderma Bastian, 1865. This is the first record of the genus Phanoderma in the East Sea, Korea.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.545-546
• /
• 2006

A problem of oil supply for a reciprocating compressor is very significant for an evaluation of reliability. Since a rotational motion of a crank shaft for the reciprocating compressor with small capacity is used for a power source of oil supply, a centrifugal force of the rotational shaft provides a stroke of oil inside the shaft like a centrifugal pump. The pumped oil rises following an inner wall and provided to a bearing passed through an oil supply hole at the side of the shaft for lubrication of the bearing. In this study, the amount of oil supply has been investigated by a numerical analysis for various conditions such as a shape of a groove, rpm of the compressor, and a shape of a flow channel. Also, a method of increasing oil supply for a low rpm has been studied so that the function can be improved for a variable condition.

• 동력기계공학회지
• /
• 제11권3호
• /
• pp.41-46
• /
• 2007

The microstructure and electrochemical analysis of welds of electric resistance welding(ERW) pipe were investigated. The direction of metal flow line in HAZ of ERW pipe shifted to the inner(or outer) surface of pipe by plastic deformation during welding. The lowest heat input welds of ERW pipe was showed crack by liquid penetrant testing. Accelerated corrosion test by constant current density of 20mA/$cm^{2}$ developed groove at the welds of ERW pipe and the measured grooving factors were about $1.2{\sim}1.5$. Corrosion potential of base metal obtained by cyclic polarization in artificial sea water(3.5wt.% NaCl solution) was 100mV higher than that of weld metal of ERW pipe.

• 대한기계학회논문집
• /
• 제16권12호
• /
• pp.2205-2215
• /
• 1992

본 연구에서는 동 베어링에 대한 해석을 바탕으로 원주방행 급유홈 프로팅링 저널베어링으로 지지된 탄성 회전체의 안정성에 대한 이론을 전개함과 동시에 실험을 통해 동 베어링의 안정성을 조사하고자 한다.

• 설비공학논문집
• /
• 제12권10호
• /
• pp.894-900
• /
• 2000

The experimental study for performance improvement of aluminum/freon22 grooved heat pipe was carried out. Arterial wick was used for performance improvement of heat pipe. The experimental result was compared with screen covered grooved wick heat pipe. And also, performance test of grooved wick thermosyphon inserted straight wire in the center of grooved pipe was carried out. This result was compared with the performance test result of grooved wick thermosyphon. The operation limit of artery inserted grooved heat pipe was slightly extended, but thermal resistance of this heat pipe was twice as large as that of screen covered grooved heat pipe. In case of thermosyphon, the operation limit of grooved thermosyphon inserted straight wire in the center of grooved pipe was slightly extended, but thermal resistance was increased, comparing with that of the grooved thermosyphon.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1406-1411
• /
• 2004

A series of experiments was conducted to examine characteristics of a grooved flat-strip heat pipe having multiple heat sources. The inner grooves of the heat pipe have the aspect ratio of 1 to $2.5(0.42{\times}1.05$ mm) whose pitch was 0.6 mm. Four block heaters ($10{\times}20$ mm) were placed in the evaporator section at intervals of 20 mm and six different heating modes were tested. The maximum surface heat flux of 80 $W/cm^2$ was achieved while the operating temperature was kept below $100^{\circ}C$, In the nearest heating mode (from the condenser location), the heat pipe exhibited more stable temperature distribution than the far heating mode where the heaters is located furthest from the condenser.

• 보존과학연구
• /
• 통권19호
• /
• pp.61-74
• /
• 1998

Conservation Treatment Process 1. Inlaying is observed at the back and head of a sword to grasp the inner structure of relics by photographing X-ray. 2. After removing rust of surface, inlaying emerge. 3. After hardening, inlaying emerge to magnetite layer by standing Scapel and Vibrotool throught microscope. Charcterization 1. Most of domestic inlaying become designed to the head of a sword but this inlaying become designed to gold inlaying to the back of a sword. 2. Inlaying is the technique to groove V-shape on the surface of relice and to put gold thread in.

• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.281-286
• /
• 2015

Automotive transmission systems are assembled with a large number of gears and shafts, and rolling bearings are used to ensure their smooth operation. Gear oil in the gear box contains solid particles such as wear debris from contacting gears and metallic chips. This particle-enriched lubricating oil can cause premature failure of the rolling bearings. Research aimed at improving the service life of these rolling bearings has been confined mainly to design and lubrication of the inner/outer rings and the rolling elements. In this paper, we redesigned the shape of the cage pocket of a deep groove ball bearing to reduce the premature failure due to particle contamination. Test bearings are assembled with this new cage design containing a hole punched in the cage pocket. Endurance tests are carried out using the contaminated lubricating oil with miracle grid as hard particle. The duration and damaged bearing component shapes are compared for two different cages. The B₁₀ life of bearing with new cage is increased by about 66% compared to the conventional cage. This is because the hard particles can be easily discharged through the pocket hole without staying for a long time in the lubrication regions. This greatly decreases abrasive wear and dents on the highly stressed ball bearing surfaces. Therefore, the cage design of this study, containing a pocket hole, can significantly delay the premature failure of rolling bearings and improve the endurance life.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.424-426
• /
• 2008

초소형 가스터빈에 사용되는 소형 고속 구름베어링의 연료윤활 특성을 실험적으로 조사하였다. 윤활유로는 항공용 가스터빈에서 사용되는 MIL-PRF-7808 터빈오일과 항공용 가스터빈의 추진연료로 사용되는 JP-8 연료를 사용하여 운용특성을 비교하였고, 시험용 베어링으로는 내경 17 mm의 깊은 홈(deep groove) ball bearing과 내경 20 mm의 원통형(cylindrical) roller bearing을 사용하였다. 베어링의 연료윤활에 따른 특성을 비교하기 위하여 오일 및 연료를 공급하며 고속베어링 시험을 수행할 수 있는 시험 장치를 개발하여 하중, 냉각공기 온도, 윤활유량 및 회전속도를 변화시키면서 시험을 수행하였다. 30,000 rpm에서 70,000 rpm까지 회전속도를 변화시키면서 시험한 결과 깊은 홈 볼베어링은 축하중과 회전속도가 증가하는 경우 베어링 케이지에 마모가 발생하였으며 마모상태는 오일윤활보다 연료윤활시 마모가 더 많이 발생하였고 본 베어링의 속도한계인 59,000 rpm까지는 연료 윤활로 운용이 가능하다는 것을 확인할 수 있었다. 연료윤활의 경우가 오일윤활의 경우보다 베어링 온도가 더 낮은 것을 알 수 있었는데 이는 베어링의 냉각특성이 연료윤활인 경우가 오일윤활의 경우보다 더 좋기 때문이라 판단된다. 본 실험을 통하여 소형 항공용 가스터빈의 주축 베어링 윤활방식으로 연료윤활 방식이 적용 가능함을 확인할 수 있었다.