• 에너지공학
• /
• 제22권4호
• /
• pp.413-419
• /
• 2013

본 연구에서는 동심원관 형태의 MILD 연소로에서 바깥 원통의 배기가스 통로에서부터 안쪽 원통의 연소통로 사이에 연결관을 설치하고 배기가스를 유입하기 위해 벤츄리 노즐을 사용할 경우 벤츄리 노즐의 기하학적 형상 변화와 고압공기 노즐의 유속 변화에 따라 고압공기 유량, 배기가스 유입량 특성을 수치해석을 통해 살펴봄으로써 최적의 벤츄리 노즐 형상과 고압공기 유속 조건들을 도출하는 것을 본 연구의 목적으로 하였다. 본 연구의 전산 해석을 통해 고압공기 노즐 출구가 연소로 벽면에 부착된 경우와 배기가스에 노출된 경우를 비교하였고, 이 두 가지 형상에 대하여 고압공기 노즐과 벤츄리 노즐의 간격을 고압공기 노즐 직경의 1배에서 3배로 변화할 때의 유입량 특성을 살펴보았다. 또한 고압공기 노즐에서의 출구 유속을 변화하여 유입량 특성을 살펴보았다. 이를 통해 고압공기 노즐과 벤츄리 노즐의 간격이 증가하면 고압공기 노즐이 벽면에 부착된 경우는 유입량이 상대적으로 변화가 적으나 배기가스에 노출된 경우는 유입량이 증가하는 경향을 확인하였다. 또한 고압공기 노즐의 유속이 증가하면 속도가 낮은 범위에서는 유입량비가 상대적으로 증가하는 경향이 크지만 속도가 큰 영역에서는 증가하는 경향이 줄어드는 것을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3104-3109
• /
• 2007

The present study has been carried out to investigate the pumping characteristics for different figures of inlet and outlet in diffuser/nozzle based on piezoelectric micropump. Piezoelectric micropump system consists of several parts like a pumping chamber, diffuser/nozzle, piezoelectric element and tubes. Parts of the micropump connected with diffuser/nozzle and tubes have been analyzed.. The magnified parts have been classified into two different models based on their resistance. These models have been further classified into six models with each one having three different angles at the magnified parts. Each model has been compared and analyzed using the simulation tool, namely, CFD-ACE depending on their flow rates and characteristics.

• 한국분무공학회지
• /
• 제4권1호
• /
• pp.55-61
• /
• 1999

The first maximum point in the stability curve of liquid jet, i.e., the critical point is associated with the critical Reynolds number. This critical Reynolds number should be predicted by simple means. In this work, the critical Reynolds number in the stability curve of liquid jet are predicted using the empirical correlations and the experimental data reported in the literatures. The critical Reynolds number was found to be a function of the Ohnesorge number, nozzle lengh-to-diameter ratio, ambient Weber number and nozzle inlet type. An empirical correlation for the critical Reynolds number as a function of the Ohnesorge number and nozzle length-to-diameter ratio is newly proposed here. Although an empirical correlation proposed in this work may not be universal because of excluding the effects of ambient pressure and nozzle inlet type, it has reasonably agrees with the measured critical Reynolds number.

• 한국유체기계학회 논문집
• /
• 제8권5호
• /
• pp.29-34
• /
• 2005

In this study, the effect of flow settling means on the performance of fan tester were numerically investigated by using a computational fluid dynamics (CFD). The airflow rate was calculated from the pressure differential across a flow nozzle in the measuring plane and the flow settling means were generally installed in the chamber of the fan tester to provide proper airflow patterns ahead of the measuring plane. The predicted nozzle differential pressures with uniform inlet velocities were compared with the values of the ANSI/AMCA 210-99 to verify the performance of the commercial CFD code CFX 5.6. The influence of flow settling means on the measurement of airflow rate in a fan tester were discussed with various porosities and inlet jet velocities. The results obtained show that the proper band of porosities exist to meet the AMCA standard in a specified inlet jet velocity.

• 한국유체기계학회 논문집
• /
• 제9권4호
• /
• pp.43-48
• /
• 2006

In this study, the effect of flow settling means on the performance of fan tester were numerically investigated by using a computational fluid dynamics(CFD). The airflow rate was calculated from the pressure differential across a flow nozzle in the measuring plane and the flow settling means were generally installed in the chamber of the fan tester to provide proper airflow patterns ahead of the measuring plane. The predicted nozzle differential pressures with uniform inlet velocities were compared with the values of the ANSI/AMCA 210-99 to verify the performance of the commercial CFD code CFX 5.6. The influence of flow settling means on the measurement of airflow rate in a fan tester were discussed with various porosities and inlet jet velocities. The results obtained show that the proper band of porosities exist to meet the AMCA standard in a specified inlet jet velocity.

• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.45-50
• /
• 2008

Molecular flows inside a guide block in the OLED(organic luminescent emitting device) deposition process have been simulated using DSMC(direct simulation Monte Carlo) method. Because the organic materials are evaporated under vacuum, molecules flow at a high Knudsen number of the free molecular regime, where the continuum mechanics is not valid. A guide block is designed as a part of the linear cell source to transport the evaporated materials to a deposition chamber, When solving the flows, the inlet boundary condition is proved to affect significantly the whole flow pattern. Thus, it is proposed that the pressure should be specified at the inlet. From the analysis of the density distributions at the nozzle exit of the guide block, it is shown that the longer nozzle can emit molecules more straightly. Finally, a nondimensionalized mass flow profile is obtained by numerical experiments, where various nozzle widths and inlet pressures are tested.

• 한국추진공학회지
• /
• 제22권6호
• /
• pp.56-63
• /
• 2018

저선회 연소기에서는 노즐출구의 속도장과 예혼합화염의 전파속도 간 균형에 의해 화염이 부상되어 존재한다. 저선회 화염의 부상높이에 대한 이해는 연소기의 안정성 및 노즐팁의 열화와 관련하여 중요한 문제이다. 이전의 실험적 연구로부터 입구 속도의 증가에 따라 화염부상높이가 오히려 감소하는 현상이 관찰된 바 있다. 선회익을 통과하는 환형 유동과 난류생성판을 통과하는 중심유동 간의 복잡한 유동장을 규명하기 위하여, 입구 속도를 바꾸어가며 비반응 유동장에 대한 수치해석을 수행하였다. 입구 속도에 따른 노즐 출구에서의 유동구조를 분석하여 실험에서 관찰된 비직관적 경향에 대한 정성적 설명을 도출하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권6호
• /
• pp.1330-1335
• /
• 2001

A present study is the flow characteristics of impinging jet by PIV measurement and numerical analysis. The flow characteristics of impinging jet flow are affected greatly by nozz1e inlet velocity An circular sharp edged nozzle type($45^{\circ}$ ) was used to achieve uniform mean velocity at the nozz1e inlet, and its diameter is 10 mm(d). Therefore, the flow characteristics on the impinging jet can be changed largely by the control of main flow In this parent study, we investigate the effects of inlet velocity, its variable is nozzle inlet Reynolds numbers (Re=1500, 3000, 4500, 6000 and 7500)

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.411-412
• /
• 2007

• Nuclear Engineering and Technology
• /
• 제54권1호
• /
• pp.401-413
• /
• 2022

This paper provides a simple method by which to estimate the cross-section stress profiles for nozzles designed according to ASME Code Section III. Further, this method validates the effectiveness of earlier work performed by the authors on standard nozzles. The method requires only the geometric information of the pressure vessel and the attached nozzle. A PWR direct vessel injection nozzle, a PWR outlet nozzle, a PWR inlet nozzle and a BWR recirculation outlet nozzle are selected based on their corresponding specific designs, e.g., a varying nozzle radius, a varying nozzle thickness and an outlet nozzle boss. A cross-section stress profile comparison shows that the estimates are in good agreement with the finite element analysis results. Differences in stress intensity factors calculated in accordance with ASME BPVC Section XI Appendix G are discussed. In addition, a change in the dimensions of an alternate nozzle design relative to the standard values is discussed, focusing on the stress concentration factors of the nozzle inside corner.