• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.154-154
• /
• 2006

Samsung Electro Mechanics ink jet has developed ultra high resolution alignment system. The alignment system has been developed for repeatable printing of conductive ink. The resolution of alignment system is 0.5um and the velocity of printing working plate is 1.5m/s. So far repeated printing results included sintering process have over 30um of drop mislocation data. In order to improve line thickness and conductivity of metal line, we need to develop the higher mechanical accurate align system. On the demand, this developed align system has under $1{\sim}2{\mu}m$ mispositioning performance and can measure of mechanical accuracy of inkjet printer, as well as the straightness of jetted drop from inkjet head. There is no kinds limit of substrate and ink to use SEM alignment system. By using this alignment system, we progress two experiment of reiterate printing drop and making conductive line on the glass and photo paper. Optical microscope and 3D profiler has been used for measurement of printed ink.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.19.2-19.2
• /
• 2010

Printed electronics using printing process has broadened in all respects such as electrics (lighting, batteries, solar cells etc) as well as electronics (OLED, LCD, E-paper, transistor etc). Copper is considered to be a promising alternative to silver for printed electronics, due to very high conductivity at a low price. However, Copper is easily oxidized, and its oxide is non-conductive. This is the highest hurdle for making copper inks, since the heat and humidity that occurs during ink making and printing simply accelerates the oxidation process. A variety of chemical treatments including organic capping agents and metallic coating have been used to slow this oxidation. We have established synthetic conditions of copper nanoparticles (CuNPs) which are resistant to oxidation and average diameter of 20 to 50nm. Specific resistivity should be less than $4\;{\mu}{\Omega}{\cdot}cm$ when sintered at lower temperature than $250^{\circ}C$ to be able to apply to conductive patterns of FPCBs using ink-jet printing. Through this study, the parameters to control average diameter of CuNPs were found to be the introduction of additive agent, the feeding rate of reducing agent, and reaction temperature. The CuNPs with various average diameters (58, 40, 26, 20nm) could be synthesized by controlling these parameters. The dispersed solution of CuNPs with an average size of 20 nm was made with nonpolar solvent containing 3 wt% of binder, and then coated onto glass substrate. After sintering the coated substrates at $250^{\circ}C$ for 30 minutes in nitrogen atmosphere, metallic copper film resulted in a specific resistivity of $4.2\;{\mu}{\Omega}{\cdot}cm$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.201-208
• /
• 2016

Ceramic pigments, which show good thermal and chemical stabilities, have been applied for various industry with development of digital printing technology. Ceramic inkjet printing has advantages of high efficiency of ink usage and eco-friendly process. Thus, the interest of the ceramic pigments with various function and color including CMYK (cyan, magenta, yellow, black) digital primary color is increasing. Here, we investigated the thermal and chemical stabilities of white ceramic pigment for digital inkjet printing process. The microstructure and crystal structure of MgO, $Al_2O_3$, $MgAl_2O_4$, $CeO_2$ were analyzed, and the stability with glaze were evaluated. In order to evaluate the applicability for digital inkjet printing, the chemical stability of white ceramic pigments at high temperature was investigated by characterization of the mixed color properties with CMYK ceramic pigments after firing process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.81-81
• /
• 2009

Non-sintered Alumina films were fabricated via inkjet printing processes without a high temperature sintering process. The packing density of these inkjet-printed alumina films measured around 60%. Polymer resin was infiltrated thru these non-sintered films in order to fill out the 40% of voids constituting the rest of the inkjet-printed films. The concept of inkjet-printed Alumina-Resin hybrid materials was designed in order to be applicable to the ceramic package substrates for 3D-system module integration which may possibly substitute LTCC-based 3D module integration. So, the dielectric properties of these inkjet-printed $Al_2O_3$ hybridmaterialsareofourgreatinterest. We have measured dielectric constant and dissipation factor of the inkjet-printed $Al_2O_3$-resinhybridfilmsbyvaryingtheamountofresininfiltratedthruthe$Al_2O_3$films.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.468-471
• /
• 2013

In this paper, we analyzed the effects of the number of TIPS-pentacene droplets and also the substrate temperature on the performance of OTFTs. As the number of the droplets increased, the mobility increased and reached the peak value and then reduced at the all temperatures. The peak mobility was $0.14{\pm}0.03cm^2/V{\cdot}sec$ at 3 droplets and $41^{\circ}C$, $0.19{\pm}0.02cm^2/V{\cdot}sec$ at 4 droplets and $46^{\circ}C$, and $0.35{\pm}0.10cm^2/V{\cdot}sec$ at 7 droplets and $51^{\circ}C$. The reason of existence of peak mobility can be found in matching the evaporation of solvent with the velocity of crystal formation. When two parameters were properly matched, the mobility produced the highest.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.1
• /
• pp.118-122
• /
• 2009

Organic thin film transistors with a pentacene active layer and various polymer gate insulators were fabricated and their performances were investigated. Characteristics of pentacene thin film transistors on different polymer substrates were investigated using an atomic force microscope (AFM) and x-ray diffraction (XRD). The pentacene thin films were deposited by thermal evaporation on the gate insulators of various polymers. Hexamethyldisilazane (HMDS), polyvinyl acetate (PVA) and polymethyl methacrylate (PMMA) were fabricated as the gate insulator where a pentacene layer was deposited at 40, 55, 70, 85, 100 oC. Pentacene thin films on PMMA showed the largest grain size and least trap concentration. In addition, pentacene TFTs of top-contact geometry are compared with PMMA and $SiO_2$ as gate insulators, respectively. We also fabricated pentacene TFT with Poly (3, 4-ethylenedioxythiophene)-Polysturene Sulfonate (PEDOT:PSS) electrode by inkjet printing method. The physical and electrical characteristics of each gate insulator were tested and analyzed by AFM and I-V measurement. It was found that the performance of TFT was mainly determined by morphology of pentacene rather than the physical or chemical structure of the polymer gate insulator

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.1 s.256
• /
• pp.51-61
• /
• 2007

This paper presents numerical and theoretical studies of acoustic wave interactions in slightly compressible liquids within piezoelectrically driven inkjet print heads. The interconnected flow channels may cause jet crosstalk, resulting in poor printing quality. It should be reduced by modifying the channel structure with the acoustic wave interactions considered. Compressible gas flow driven by the sudden movement of a top wall in the channel is calculated using Flow3D and is validated with the narrow gap theory. Limited compressibility model of the Flow3D is employed to calculate pressure waves of slightly compressible ink flow. It is found that reducing restrictor width can damp out the jet crosstalk by inhibiting the pressure wave propagation. The degree of crosstalk has been quantified using the maximum values of cross-correlations between neighboring channels and a critical channel dimension for acceptable crosstalk has been proposed. This finding is verified by drop visualization experiments using silicon-micromachined piezo inkjet print heads that are fabricated by our group.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.18 no.1
• /
• pp.35-45
• /
• 2000

Recently, as the prepress mainstream is changed to the digital workflow, various digital proofing systems such as high price dye sublimation printers and low price ink jet printers are widely used in printing industry. However, most of the digital proofing devices have lower resolution than analog proofing systems and differ with actual color presses in the color gamuts. Therefore, proper color compensations are needed for digital color proofing in order to match colors between the proofs and the press sheets. This study shows the application method of Look-up Table to the digital color proofer of Rainbow, the analog proofer of Matchprint-II, and an actual offset press is effective on the color compensations.

• Journal of the Korean Society of Visualization
• /
• v.15 no.2
• /
• pp.21-25
• /
• 2017

If a liquid droplet evaporates on a solid substrate, when it completely dries, it leaves a peculiar pattern, which depends on the composition of the liquid. Not only a single component liquid but also complex liquids are studied for a different purpose. In particular, a binary mixture droplet has been widely studied and used for an ink-jet printing technology. In this study, we focus on investigating to visualize the internal flow field of an ethanol-water mixture by varying a concentration ratio between two liquids. We measure the in-plane velocity vector fields and vorticities. We believe that this fundamental study about the internal flow field provides a basic idea to understand the dried pattern of the binary mixture droplet.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.215-219
• /
• 2004

We reported two new techniques of barrier rib formation that are applicable to a variety of structures for high-efficiency PDPs suitable for mass-production [1]. These two methods are mold replication and direct glass sculpting. Especial progress has since been made in improving these methods to be more suitable for high-efficiency PDPs with the DelTA cell structure. This paper reports photolithographic fabrication methods for the masters used in mold replication. The masters for more complex barrier rib forms are easier to make with these methods. The paper also reports a process that combines the direct glass sculpting method with an ink-jet printing method of electrode formation.