• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.98-104
• /
• 2014

The technologies employing spray-guided type combustion system for ultra-lean combustion direct injection engine is focused as a promising technology for satisfying emission regulations and improving fuel economy. In the present study, control and design optimization of lean-burn LPG direct injection engine was carried out with control strategy and injection position changes. Inter-injection spark ignition strategy was applied and the effect of the strategy was assessed at relatively higher load operation condition than previous researches. In order to create richer mixture in the vicinity of spark plug electrode, relative distance between the dead-end of injector and the electrode of spark plug was changed.

• Journal of Soil and Groundwater Environment
• /
• v.22 no.3
• /
• pp.42-49
• /
• 2017

TOUGH2 was used to simulate the migration of $CO_2$ injected into a sandy aquifer. A series of numerical simulations was performed to investigate the effects of a low-permeability layer (LPL) embedded in the aquifer on the injection rate and the pressure distribution of $CO_2$. The results show that the size and location of the LPL greatly affected the spread of $CO_2$. The pressure difference between two points in the aquifer, one each below and above the LPL, increased as the size of the LPL increased, showing a critical value at 200 m, above which the size effect was diminished. The location of the LPL with respect to the injection well also affected the migration of $CO_2$. When the injection well was at the center of the LPL, the injection rate of $CO_2$ decreased by 5.0% compared to the case with no LPL. However, when the injection well was at the edge of the LPL, the injection rate was decreased by only 1.6%. The vertical distance between the injection point and the LPL also affected the injection rate. The closer the LPL was to the injection point, the lower the injection rate was, by up to 8.3%. Conclusively, in planning geologic storage of $CO_2$, the optimal location of the injection well should be determined considering the distribution of the LPL in the aquifer.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.4
• /
• pp.787-796
• /
• 2019

In this paper, we propose the design and test measure of Ringer injection IoT system for controling the ringer injection status and notifying the server system of the collected status informations such as the completion of injection, the remaining liquid, the injection status, and the emergency alarming of the urgent patients. We design the circuit diagrams composed of linger injection sensors, switches, status indicators, wireless communication functionalities, and propose the controlling and monitoring algorithms for sensing the linger injection status and notifying the collected status informations to a server system. Furthermore, we derive the testing criteria, such as linger liquid sensing time, sensing distance, operating temperature, input power, power consumption, and wireless communication speed, and analyze the test results.

• Clean Technology
• /
• v.18 no.4
• /
• pp.410-418
• /
• 2012

The performance of the ammonia injection gun (AIG) used for maximizing the utilization of reducing agent in the selective catalytic reduction (SCR) system is decided by several parameters such as the pattern of flow distribution, geometry of the air distribution manifold (ADM) and the array and geometry of nozzles. In the study, the uniformity of jet flows from the nozzles in AIG was analyzed statistically by using the computational fluid dynamics (CFD) method to evaluate the role of design parameters on the performance of the SCR system. The uniformity of jet flows from the nozzles is being deteriorated with increasing the supplying flow rate to the AIG. Distribution rates to each branch pipe become lower with decreasing distance to the header, and flow rates from nozzle are also reduced with decreasing distance to the header. The uniformity of jet flows from nozzles becomes stable significantly when the ratio of summative area of nozzles to each sectional area of the branch pipe is below 0.5.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.32 no.5
• /
• pp.453-457
• /
• 2006

This study was designed to investigate the effect of intra-articular injection of hyaluronic acid for the treatment of internal derangements of the temporomandibular joint(TMJ). Sixteen patients with internal derangements of TMJ in 1 male and 15 females aged 68 to 18 years comprised the study material. The patients' complaint was limited mouth opening and pain during function. Patients were divided into 3 groups(articular disc displacement with reduction, articular disc displacement without reduction, osteoarthritis group). The preauricular area was disinfected anesthetized locally with 2% lidocaine hydrochloride. Arthrocentesis was performed. Hyaluronic acid(1.5 ㏄) was then injected into the superior compartment of the TMJ. Active range of motion exercises were instituted at approximately 24 hours postoperatively. Antibiotics and NSAID, three times daily by mouth, was prescribed for 3 days. Clinical evaluation of the patients was done before the procedure, immediately after the procedure, final follow-up visit postoperatively. Pain during function was assessed using visual analog scales(VAS). Maximal mouth opening was recorded as a distance between upper incisal edge and lower incisal edge. Intra-articular injection of hyaluronic acid caused significant reduction of pain during function, significant increase of maximal opening range. These findings suggest that intra-articular injection of hyaluronic acid is useful for decreasing patient reports of pain while increasing functional mobility of the mandible in internal derangements of the TMJ.

• Journal of ILASS-Korea
• /
• v.1 no.1
• /
• pp.85-91
• /
• 1996

This experiment was undertaken to investigate spray characteristics of the conventional inject ion system and the ultrasonic energy added inject ion system. Sauter mean diameter was mesured under the variation of inject ion pressure and the spray distance. To measure the droplet size we used the Malvern system 2600C. The spray angle and mass distribution was analyzed to the CCD camera and the patternater. After experiment, it was found that the ultrasonic energy added injection system had smaller sauter men diameter of droplet, wider mass distribution and wider spray angle than the conventional inject ion system had.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.149-156
• /
• 2007

Non-contact transportation of the large-sized glass plate using air-cushion is considered for sputtering system of LCD panel. The Argon gas from second gas injection holes is injected to levitate and transport the glass plate. Low maximum pressure and uniform pressure distribution on the bottom surface of the glass plate must be maintained for stable levitation and transportation of the glass plate. Therefore, the analysis of fluid flow between the glass plate and the air-pad is numerically performed for varying space between the injection holes in this study. The pressure uniformity on the bottom surface of the glass plate is evaluated for overall glass plate. The distance between the injection holes must be designed below 90 mm for obtaining the low maximum pressure and uniform pressure distribution.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.25-26
• /
• 2005

This study suggested the occurrence source of weld-defects and its solution methods in a welding of Electrolyte injection hole by pulsed Nd:YAG laser. In experiment, the ramp down was used in order that solidification crack was removed. Furthermore, shrinkage stress and heat input were reduced by changing of weld trajectory and defocused distance. As a results of a experiment, a sound weld bead shape and crack-free weld bead can be obtained.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.16 no.1
• /
• pp.80-85
• /
• 2012

Purpose: The whole body bone scan is an examination that visualizing physiological change of bones and using bone-congenial radiopharmaceutical. The patients are intravenous injected radiopharmaceutical which labeled with radioactive isotope ($^{99m}Tc$) emitting 140 keV gammarays and scanned after injection. The 3 principles of radiation protection from external exposureare time, distance and shielding. On the 3 principles of radiation protection basis, radiopharmaceutical might just as well be injected rapidly for reducing radiation because it might be the unopened radiation source. However the radiopharmaceuticals are injected into patient directly and there is a limitation of distance control. This study confirmed the change of radiation exposure as change of distance from radiopharmaceutical and observed the change of radiation exposure afte rsetting a shelter for help to control radio-technician's exposure. Materials & methods: For calculate the average of injection time, the trained injector measured the injection time for 50 times and calculated the average (2 minutes). We made a source as filled the 99mTc-HDP 925 MBq 0.2 mL in a 1 mL syringe and measured the radiation exposure from 50 cm,100 cm,150 cm and 200 cm by using Geiger-Mueller counter (FH-40, Thermo Scientific, USA). Then we settled a lead shielding (lead equivalent 6 mm) from the source 25 cm distance and measured the radiation exposure from 50 cm distance. For verify the reproducibility, the measurement was done among 20 times. The correlation between before and after shielding was verified by using SPSS (ver. 18) as paired t-test. Results: The radiation doses according to distance during 2 minutes from the source without shielding were $1.986{\pm}0.052{\mu}$ Sv in 50 cm, $0.515{\pm}0.022{\mu}$ Sv in 100 cm, $0.251{\pm}0.012{\mu}$ Sv in 150 cm, $0.148{\pm}0.006{\mu}$ Sv in 200 cm. After setting the shielding, the radiation dose was $0.035{\pm}0.003{\mu}$ Sv. Therefore, there was a statistical significant difference between the radiation doses with shielding and without shielding ($p$<0.001). Conclusion: Because the great importance of whole body bone scan in the nuclear medicine, we should make an effort to reduce radiation exposure during radiopharmaceutical injections by referring the principles of radiation protection from external exposure. However there is a limitation of distance for direct injection and time for patients having attenuated tubules. We confirmed the reduction of radiation exposure by increasing distance. In case of setting shield from source 25 cm away, we confirmed reducing of radiation exposure. Therefore it would be better for reducing of radiation exposure to using shield during radiopharmaceutical injection.

• Journal of Sensor Science and Technology
• /
• v.19 no.1
• /
• pp.1-7
• /
• 2010

Electrostatic capacitance measurement method in a fine hose was proposed, in which two ring-type electrodes were disposed on the hose in the direction of fluid flow instead of the conventional face-to-face electrodes. With the proposed electrode structure, we realized a Ringer's solution exhaustion detector for an IV(invasive vein) injection set. On a 4 mm-diameter hose of IV set, we disposed two ring-type electrodes of 10 mm width at a distance of 5 mm each other and obtained 0.72 pF and 2.51 pF for air and 10 % dextrose Ringer's solution in the hose, respectively. The capacitance between the two electrodes varied with the hose-wraparound coverage of electrode as well as the width of electrode and the distance between the electrodes. For hose-wraparound electrode coverage of 75 %, the capacitance varied from 0.62 pF to 1.98 pF with the Ringer's solution level between the two electrodes. A charge amplifier converted the capacitance. variation into electric signal and a comparator was used to detect whether Ringer's solution was exhausted or not. The result was delivered to a host using a RF transmitter with 320 MHz carrier frequency.