• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.271-274
• /
• 2007

Housing and insulation of electrical connectors are made of plastic resin by injection molding process. The metallic inner tube is easily deformed by high pressure during the injection process. In order to prevent deformation of the inner tube, it is desirable to simulate it by structural CAE analysis. However, it takes a long time to calculate the stress- of the part by commercially available injection molding CAE software with sufficient accuracy. In this study, structural analysis in conjunction with injection molding analysis is proposed to improve accuracy of the structural analysis. Pressure distribution on the inner tube is predicted by the injection molding CAE analysis, and then mapped onto the mesh of structural analysis by a mapping algorithm developed in this study. As a result reliable result is obtained in shorter time than the conventional method. The predicted deformation of the inner tube is compared with the actual part after experiment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.161-166
• /
• 2012

Intravenous (IV) injection is widely used to supply Ringer solution directly into a vein in hospital. Generally, a passive injection method has been used, which causes the inconsistent flow rate of fluid and inappropriate control of injection time by a patient. It leads to an unnecessary nurse's overwork and decrement of IV injection's effect. To solve these problems, flow control infusion pumps have been developed. But because of relatively heavy weight and high price, its usage has been limited. In the present study, a new automatic IV injection system is developed. It is installed with a small pressing mechanism driven by a small electric motor to regulate the flow rate by pressing tube. Proportional integral derivative (PID) feedback control algorithm is applied to control the electric motor. The system is smaller in size and uses lower power than the existing commercial product. The newly developed system is also installed with networking capability, which enables monitoring the status of several automatic IV injection system at the same time.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.9
• /
• pp.47-58
• /
• 2010

This paper presents the injection efficiency of 2.0 shot system which was verified by strength and injection time. In order to perform this study, laboratory model tests and field tests are carried out. The laboratory model tests consist of the test of injection time for verifying the injection ratio, and the tests of homo-gel and sand-gel strengths for estimating the characteristic of strength. It is found that the injection ratio of 1:2 shows the best seepage into the ground. The results of the strengths are also larger than other injection ratio. The large strength will also be expressed by field tests at construction site.

• Journal of Mechanical Science and Technology
• /
• v.20 no.12
• /
• pp.2284-2291
• /
• 2006

The present study investigates gas residence time and mixing characteristics for various swirl numbers generated by injection of secondary air into a lab-scale cylindrical combustor. Fine dust particles and butane gas were injected into the test chamber to study the gas residence time and mixing characteristics, respectively. The mixing characteristics were evaluated by standard deviation value of trace gas concentration at different measurement points. The measurement points were located 25 mm above the secondary air injection position. The trace gas concentration was detected by a gas analyzer. The gas residence time was estimated by measuring the temporal pressure difference across a filter media where the particles were captured. The swirl number of 20 for secondary air injection angle of 5$^{\circ}$ gave the best condition: long gas residence time and good mixing performance. Numerical calculations were also carried out to study the physical meanings of the experimental results, which showed good agreement with numerical results.

• Korean Journal of Digital Imaging in Medicine
• /
• v.15 no.1
• /
• pp.21-26
• /
• 2013

To be investigated and measures to reduce the medical exposure of patients to change the Epidural Injection time Fluoroscopy Pulse Rate in this study. Was conducted in 50 patients who underwent surgery Epidural Injection performed by interventional care of Konkuk University Hospital from January to April 2013. The treatment time with the change of Pulse rate, is measured in minutes fluoroscopy time, and measured the area dose (${\mu}Gym^2$) and depth dose (mGy). Using the Image J program, to measure the PSNR and SNR. The fluoroscopy time as a result surgery, there was no significance in the statistical analysis, and depth dose is 34.3 to 34.9%, was reduced from 35.8 to 38.7% the area dose. It is possible to reduce the appropriate Pulse rate, to reduce the dose without statistical analysis significance fluoroscopy time.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.8 no.3
• /
• pp.150-156
• /
• 1975

This paper dealt itself with the relation of the heat release rate with crank angle in combustion process by adjusting the injection time, injection amount and engine speed of diesel engine. The result of test were obtained by analyzing indicator diagram of KUBOTA 2LKE diesel engine, where the indicator was used Tertronix oscilloscope. The combustion period of diesel engine is composed of premixed burning time and combustion controlled time. The larger the premixed burning region, the higher efficiency was obtained with the higher maximum pressure than at the time of the normal smooth operation. The longer the combustion controlled time, the lower the maximum pressure than the period of the normal operation, but the efficiency was decreased. The region of premixed burning was principally controlled by injection delay, but combustion controlled time was affected when oxygen and fuel were mixed. Efficiency of engine was increased at the time of earlier injection time under the constant injection amount, and engine speed, but the pressure increasing was observed higher than the efficiency increasing.

• Design & Manufacturing
• /
• v.14 no.2
• /
• pp.42-48
• /
• 2020

This study is on the injection molding analysis for the LED outdoor lighting top cover of one heat sink body type structure. Thermoplastic and thermosetting resins were applied to compare the thermal properties during the injection molding process. The thermoplastic resin is used in this study due to special characteristics that it is light, good strength and dose long not transmute quality even if pass long time. The thermosetting resin is applied to this study due to good in strength, lightweight and excellent etc, thermal conductivity. This study presented a preliminary analysis of fill time, weld line, air trap etc. for the injection molding process of LED lamp cover and body through simulation using Moldflow. As a result of the study, it was selected HTM-102 material because the thermosetting resin has excellent strength and heat conductivity.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.23-27
• /
• 2005

Generally, when the injection molds are made in advanced nations, the improvement of a quality and production rate is obtained by using CAE. In this paper, the methodology which is possible to reduce the cycle time of injection molding process is studies by using the cooling analysis with CAE(Moldmax). In case of changing the cooling system design with the analysis result of CAE, the manimum reduction of the cycle time runs into 30 percent. Finally, the average reduction of the cycle time is 17.8 percent.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.84-90
• /
• 2018

When producing a plastic horn cover for an automobile, since the interval between the ribs on the inner surface is narrow, conventional cooling channels cannot be applied and cooling of the mold is difficult. For this reason, the molding operation cannot be completed within a set cycle time. In this study, a conformal cooling channel was applied on the mold to solve the cooling problem. Injection molding simulation was carried out to confirm the effectiveness of the conformal cooling channel. In the analysis results, the mold temperature at the rib section decreased by 33%, and the mold temperature also decreased by 31%. This reduction in temperature allowed for molding within a set cycle time and demonstrated the effectiveness of the conformal cooling channel.

• Archives of Plastic Surgery
• /
• v.36 no.5
• /
• pp.654-659
• /
• 2009

Purpose: A botulinum toxin type A (BoNT - A) injection has been used as a noninvasive management for lower face contouring since 2000. The aim of this study was to compare reduction rate of lower face width for a longtime according to repeated Botox$^{(R)}$ injections on masseter muscles for lower face contouring procedure. Methods: Forty - five patients were analyzed for single session of Botox$^{(R)}$ injection and 13 patients were evaluated for repeated Botox$^{(R)}$ injections for over two years. Single injection group was tracked regular intervals at 1, 3, 6, 10, 12 months after injection, and repeated injection group was measured at every injection time. Twenty - five to thirty units of Botox$^{(R)}$ was injected into each masseteric muscle at five to six points at the prominent portions of the mandibular angle. Standardized frontal view of digital photographs were analyzed by Adobe Photoshop$^{(R)}$ (version CS3) to measure an reduction rate of lower face width. Results: Reduction rate was 3.7%, 6.9%, 6.2%, 4%, 4% at 1, 3, 6, 10, 12 months post injection each other in single injection group. However, more than 8% reduction rate was found in repeated injection group persistently for more than two years. Conclusion: This study shows that effective duration of Botox$^{(R)}$ injection for lower face contouring is expected to continue over one year clinically. Moreover, repeated injections maintained lower reduction rate consistently for a long time. Therefore, repeated injections on masseter muscles at regular intervals are most effective procedure for lower face contouring.