• Journal of ILASS-Korea
• /
• v.27 no.4
• /
• pp.181-187
• /
• 2022

For carbon neutrality, direct-injection hydrogen engines are attracting attention as a future power source. It is essential to estimate the transient injection rate of hydrogen for the optimization of hydrogen injection in direct injection engines. However, conventional injection rate measurement techniques for liquid fuels based on the injection-induced fuel pressure change in a test section are difficult to be applied to gaseous fuels due to the compressibility of the gas and the sealing issue of the components. In this study, a momentum flux measurement technique is introduced to obtain the transient injection rate of gaseous fuels using a force sensor. The injection rate calculation models associated with the momentum flux measurement technique are presented first. Then, the volumetric injection rates are estimated based on the momentum flux data and the calculation models and compared with those measured by a volumetric flow rate meter. The results showed that the momentum flux measurement can detect the injection start and end timings and the transient and steady regimes of the fuel injection. However, the estimated volumetric injection rates showed a large difference from the measured injection rates. An alternative method is suggested that corrects the estimated injection rate results based on the measured mean volumetric flow rates.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

• The Korean Journal of Pain
• /
• v.32 no.1
• /
• pp.39-46
• /
• 2019

Background: Lumbosacral transforaminal epidural injection (TFEI) is an effective treatment for spinal disease. However, TFEI may have several types of complications, some of which can be attributed to intravascular injection. We reviewed studies to compare the intravascular injection rate among different needle types. Methods: We searched the literature for articles on the intravascular injection rate among different needle types used in TFEI. The search was performed using PubMed, MEDLINE, the Cochrane Library, EMBASE, and Web of Science. Results: A total of six studies comprising 2359 patients were identified. Compared with the Quincke needle, the Whitacre needle reduced the intravascular injection rate (OR = 0.57, 95% CI = [0.44-0.73], P < 0.001). However, compared with the Quincke needle, the Chiba needle did not reduce the intravascular injection rate (OR = 0.80, 95% CI = [0.44-1.45], P = 0.46). In one study, the intravascular injection rate using a blunt-tip needle was lower than that using a sharp needle. In another study, the Whitacre and the blunt-tip needle have similar intravascular injection rates, while, the catheter-extension needle showed a reduced intravascular injection rate. Conclusions: This meta-analysis showed that the Whitacre needle reduced the intravascular injection rate as compared with the Quincke needle, but failed to establish that the Chiba needle can decrease the intravascular injection rate in TFEI. Moreover, the blunt-tip needle can reduce the intravascular injection rate compared with the Quincke needle, and the catheter-extension needle can reduce the intravascular injection rate compared with the Whitacre and the blunt-tip needle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2005

Fuel injection rate of an injector is affected by various injection conditions such as injection duration, fuel temperature, injection pressure, and voltage in LPG liquid injection systems for either a port-fuel-injection(PFI) or a direct injection(DI) in a cylinder. Even fuel injection conditions are changed, the air-fuel ratio should be accurately controlled to educe exhaust emissions. In this study, correction factor for the fuel injection rate of an injector is derived from the density ratio and the pressure difference ratio. A voltage correction factor is researched from injection test results on an LPG liquid injection engine. A compensation method of the fuel injection rate is proposed for a fuel injection control system. The experimental results for the LPG liquid injection system in a SI-engine show that this system works well on experimental range of engine speed and load conditions. And the fuel injection rate is accurately controlled by the proposed compensation method.

• Journal of ILASS-Korea
• /
• v.21 no.1
• /
• pp.20-28
• /
• 2016

This paper presents an experimental study on the GDI injector with Bosch method. The injection characteristics, such as the injection quantity, the injection rate, the maximum velocity of the nozzle exit and the injection delay were studied through the change of the injection pressure, the tube pressure and energizing duration in injection rate measurement device using nheptane. The injection quantity is increased by increasing injection pressure, decreasing tube pressure or increasing energizing duration. As the difference of the injection quantity changed, the shape of injection rate was moved with a constant form. The maximum velocity of the nozzle exit showed a tendency to increase as the injection pressure is increased. However, tube pressure did not affect. Overall, it was confirmed that the closing delay is longer than the opening delay in all conditions. As the injection pressure increased, the result has a tendency to decrease the closing delay, it did not affect the opening delay. Reduction of the closing delay showed the reduction of the injection duration. the tube pressure and energizing duration did not affect the injection delay (opening delay, closing delay).

• Journal of ILASS-Korea
• /
• v.24 no.3
• /
• pp.114-121
• /
• 2019

The effect of injector driving current pattern on fuel injection rate of solenoid diesel common rail injector was studied by computer simulation. The time resolved fuel injection rate and injected quantity per stroke of a common rail injector driven with the five current patterns were computer simulated. The fuel injection rate and injected quantity per stroke according to the rail pressure and fuel injection period were also computer simulated. When the common rail injector was driven with the five driving current patterns of peak & hold, there was no difference in the fuel injection rate in the peak section regardless of all the current patterns of the five cases. On the other hand, the magnitude of the hold current value influenced the injection rate and injected quantity per stroke. That is, in the current pattern of three cases where the hold current value is equal to or more than a constant value of the peak current value, the fuel injection rates for the given common rail rail pressure and injection period are same one another. On the other hand, the current pattern of the two cases, in which the hold current value is smaller than a certain value, there is a large fluctuation in the fuel injection rate.

• Proceedings of the KSAR Conference
• /
• 2001.03a
• /
• pp.53-53
• /
• 2001

Two trials were conducted in a commercial dairy farm on heifer synchronization with PGF$_2$ $\alpha$. Animals showing estrus following the first injection were bred and animals not showing estrus were given the second injection 10 days later. In the first trial, the injection sites were rump and rump. In the second trial, the injection sites were rump and shoulder. Estrous detection was peformed 24 h after injection. Animals were bred by the same technician. In the first trial, the response rate for the first injection was 51.4% and the subsequent pregnancy rate of these animals was 60.0%. The response rate in the second injection was 57.1% and the pregnancy rate was 50.0%. In the second trial, the response rate in the first injection on the rump was 48.7% and the subsequent pregnancy rate was 70.6%. The second injection was given on the shoulder and the response rate was 60.0% and the subsequent pregnancy rate was 25.0%. The data suggests that the site of PGF2 $\alpha$ administration was critical to achieve success in estrous synchronization and pregnancy rates.

• Journal of Power System Engineering
• /
• v.1 no.1
• /
• pp.42-51
• /
• 1997

In this study, in order to investigate the influence of cam profile on the injection rate, the characteristics of injection in PLN (pump - line - nozzle) diesel injection system were simulated. Six types of the profile of fuel cam were used for simulation. The maximum injection pressure and maximum injection rate of initial and end phase were analyzed to demonstrate the characteristics of injection. The mathematical model of the injection system and the computation results were verified by experimental results. Simulation results showed that the maximum injection pressure, maximum injection rate, injection quantity and pressure drop in the end phase were proportional to the velocity of fuel cam during the effective stroke.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2003.09a
• /
• pp.462-466
• /
• 2003

This study was conducted to examine the potential of biosparging process in removing diesel contaminated soil and groundwater. The experiment was carried out lab-scale biosparging reactor and the biodegradation rate of diesel was evaluated as function of air injection rate and pattern. When renter was operated as air injection rate of 1000$m\ell$/min and pulsed air injection(15min pulse, 15min downtime), DO concentration in the renter was higher than another operating condition. The evidence for biodegradation of diesel was the $O_2$ utilization and $CO_2$ product following the cessation of sparging. Especially, air injection rate of 2000$m\ell$/min and pulsed air injection(15min pulse, 15min downtime) enhanced the diesel biodegradation during the operating. After 120day, the biodegradation rate of diesel was decreased as the lack of carbon source.

• Journal of ILASS-Korea
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2009

This paper present the diesel fuel spray evolution and atomization performance in a multi-hole nozzle in terms of injection rate, spray evolutions, and mean diameter and velocity of droplets in a compression ignition engine. In order to study the effect of split injection on the diesel fuel spray and atomization characteristic in a multi-hole nozzle, the test nozzle that has two-row small orifice with 0.2 mm interval was used. The time based fuel injection rate characteristics was analyzed from the pressure variation generated in a measuring tube. The spray characteristics of a multi-hole nozzle were visualized and measured by spray visualization system and phase Doppler particle analyzer (PDPA) system. It was revealed that the total injected fuel quantities of split injection are smaller than those of single injection condition. In case of injection rate characteristics, the split injection is a little lower than single injection and the peak value of second injection rate is lower than single injection. The spray velocity of split injection is also lower because of short energizing duration and small injection mass. It can not observe the improvement of droplet atomization due to the split injection, however, it enhances the droplet distributions at the early stage of fuel injection.