• 폴리머
• /
• 제28권3호
• /
• pp.263-272
• /
• 2004

자동차 계기판을 제조하는 기체 사출 성형의 공정에 있어서 전산 모사를 통한 공정성 및 제조된 제품의 물성 향상에 관한 연구를 수행하였다. ABS 삼원공중합체의 P-V-T 자료를 이용하여 기체 사출 공정을 적용하였으며 시간에 따른 금형 충전 효과를 예측하였다. 또한 기체 사출 성형에 있어서 압력, 충전 시간, 기체의 주입 통로 및 런너의 위치 등 다양한 가공 인자들을 변화시킴으로서 공정의 최적 조건을 찾을 수 있었다. 이러한 전산 모사를 통하여 확립된 공정을 통해 제조된 계기판은 일반적인 사출 성형법에 의해 제조되어진 제품에 비해서 우수한 치수 및 변형 안정성이 개선되었다.

• 한국정밀공학회지
• /
• 제19권11호
• /
• pp.83-88
• /
• 2002

In order to predict the moldability of a injection molded part, a simulation of filling is needed. Short shot is one of the most frequent troubles encountered during injection molding process. The adjustment of process conditions is the most economic way to troubleshoot the problematic short shot in cost and time since the mold doesn't need to be modified at all. But it is difficult to adjust the process conditions appropriately in no times since it requires an empirical knowledge of injection molding. In this paper, the intelligent CAE system synergistically combines fuzzy-neural network (FNN) for heuristic knowledge with CAE programs for analytical knowledge. To evaluate the intelligent algorithms, a cellular phone flip has been chosen as a finite element model and filling analyses have been performed with a commercial CAE software. As the results, the intelligent CAE system drastically reduces the troubleshooting time of short shot in comparison with the experts' conventional methodology which is similar to the golden section search algorithm.

• 소성∙가공
• /
• 제22권1호
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.1-8
• /
• 2017

Warpage is a major defect frequently found in the injection molding process, and the reduction of warpage is a very challenging problem because of the uncontrollable factors, such as variations in the process parameters. Without any countermeasure against these noises, attempts to reduce the defects often lead to failure. In this research, a new robust design methodology, based on the Mahalanobis Taguchi System (MTS) to reduce warpage, is presented. The MTS performs the orthogonal array experiments and uses the signal-to-noise (SN) ratio of the Mahalanobis distance as a performance metric. The validity of the proposed method is illustrated through an optimal design of the injection molding process of a CPU base plate.

• 한국기계가공학회지
• /
• 제18권10호
• /
• pp.34-41
• /
• 2019

Warpage and weld line are two major cosmetic defects in the injection molding process. These defects are very sensitive to uncontrollable parameters within the process. The optimization of the design variables can be treated with the use of robust designs. Therefore, in order to minimize the warpage and weld line, a special design method to diminish defects is required. In this study, a new robust design method using designer preference to achieve the optimal robust design conditions in the injection molding process is proposed. The effectiveness of the proposed method is shown with an example of the part of warpage and weld line.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.11-16
• /
• 2020

In this study, forming of carbon composite parts was performed using an injection/compression molding process. An impregnation of matrix is determined by ability of wet and flow rate between the matrix and reinforcement. The flow rate of matrix passing through the reinforcements is a function of permeability of reinforcement, a viscosity of matrix and pressure gradient on molding, and the viscosity of the matrix depends on the mold temperature, molding pressure and shear strain of matrix. Therefore, compression molding experiment was conducted using a heating mold in order to confirm the possibility of matrix impregnation. The impregnation of the matrix through the porosities between the woven yarns was confirmed by the cross-sectional SEM image of compression molded parts. An injection molding process was also performed at a short cycle time, high molding pressure and low mold temperature than those of compression experiment conditions. Deterioration of impregnation on the surface of molded parts were caused by these injection conditions and it could be the reason of decreasing the maximum tensile strength. In order to improve impregnation of matrix on the surface, injection/compression molding and insert-over molding were applied. As a result of applying injection/compression molding and insert-over molding, it was shown that the improvement of impregnation on the surface and the maximum tensile strength was increased about 2.8 times than the virgin matrix.

• Korea-Australia Rheology Journal
• /
• 제20권2호
• /
• pp.79-88
• /
• 2008

In this study, we focus on the improvement of the filling efficiency in injection molding by application of ultrasonic vibration. While studies about the filling efficiency of typical filling processes in the injection molding have been widely performed, there have been only few studies about the filling efficiency of an ultrasonic process. The effect of the ultrasonic vibration is an important process condition, which influences the flow characteristics of polymer melt. This new condition even affects well-known injection conditions such as cavity pressure, injection temperature and mold temperature. For this study, we carried out a numerical analysis by appropriate modeling and analysis of the ultrasonic process in the filling process. To verify this numerical analysis, we compared the numerical results with the experimental data. Also, we analyzed the filling process in a thin cavity using this numerical analysis. To understand the flow characteristics of polymer melt in the ultrasonic process, we substituted real and complex vibration conditions with simplified and classified conditions according to the position of vibrating cavity surfaces and the phase difference between two opposing cavity surfaces. We also introduced MFR (melt flow ratio) as a new index to estimate the filling efficiency in the ultrasonic process.

• Current Applied Physics
• /
• 제18권11호
• /
• pp.1451-1457
• /
• 2018

Injection compression molding (ICM) is an advantageous processing method for producing thin and large polymeric parts in a robust manner. In the current study, we employed the ICM process for an energy-related application, i.e., thin and large polymeric battery case. A mold for manufacturing the battery case was fabricated using injection molding. The filling behavior of molten polymer in the mold cavity was investigated experimentally. To provide an in-depth understanding of the ICM process, ICM and normal injection molding processes were compared numerically. It was found that the ICM had a relatively low filling pressure, which resulted in reduced shrinkage and warpage of the final products. Effect of the parting line gap on the ICM characteristics, such as filling pressure, clamping force, filling time, volumetric shrinkage, and warpage, was analyzed via numerical simulation. The smaller gap in the ICM parting line led to the better dimensional stability in the finished product. The ICM sample using a 0.1 mm gap showed a 76% reduction in the dimensional deflection compared with the normal injection molded part.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.5-10
• /
• 2008

Recently, ultra precision and light-weight micro products are needed in various industries. Injection molding products with metal insert material is often satisfied with light-weight and precision simultaneously. The researches on macro-size insert deformation have been performed but, a research on micro-size insert is meager. In this paper, the injection molding product with $300{\mu}m$ thin foil insert is designed and insert injection molding process is performed. Finally, the deformation of thin foil insert is analyzed according to insert feature and gate length.

• Design & Manufacturing
• /
• 제11권3호
• /
• pp.25-28
• /
• 2017

The production of carbon fiber reinforced thermoplastics(CFRTP) parts using an injection/compression molding process that differs from the conventionally used fabrication methods was investigated Before the application of composite molding in the injection/compression molding process, a simple compression molding experiment was performed using a hydraulic press machine to determine the characteristics of resin impregnation and to obtain a basic physical property data for the CFRTP. Based on these results, injection/compression molded specimens were manufactured and an additional insert/over molding process was applied to improve the impregnation rate of the molded specimens. The results demonstrated that the tensile strength of the molded parts using the faster injection/compression process was similar to that of a hydraulic press molded product.