• 대한치과교정학회지
• /
• 제5권1호
• /
• pp.33-41
• /
• 1975

To study the effect of the tetracycline-HCl on the growth of the rats, the author made a daily injection of tetracycline-HCl in the amount of 40mg/kg of body weight to the lactating mother and weanling rats for 7 days. Lactating and weanling young rats were killed at a week intervals and removed tibia and mandible from soft tissues. The effect of the tetracycline on the growth of rats were analysed from the weight, the length of tibia and the size of mandible. The results were as follows: 1. Tetracycline inhibited the growth of young rats. 2. Inhibitory effects were greater ill the weanling group than the lactating group. 3. The inhibitory effect was marked just after the injection of tetracycline-HCl in body weight and after a week in mandible and tibia. 4. The inhibitory effect of growth nab continued for 2-3 weeks in body weight and 3-4 weeks in tibia and mandible. 5. In growth of mandible, the antero-posterior growth was more inhibited than the vertical.

• 한국양식학회지
• /
• 제12권4호
• /
• pp.275-281
• /
• 1999

The utility of RSV-LTR and carp beta-actin promoters was evaluated in a marine flatfish species, Limanda Yokohamae by examining successful expression of transgenic DNA in muscles (transfected by direct injection) and in early embryos (transformed by lipofected sperm). The expressed pattern of injected DNA in skeletal muscles was dependent on the DNA amount injected. The activity reached to maximal level at 48 hours post injection, and persisted up ot 1 month transiently. Gene transfer into early embryo of this species was successfully achieved using lipofected sperm with the efficiency ranging 36.8% to 48.1%. The expression of transgene during embryonic development was shown as stage-specific and transient.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.346-349
• /
• 2001

Nowadays the amount of plastic products is increasing in modern industry. Plastic materials are continuously developed to satisfy the mechanical, physical, and chemical properties. The increasing application of plastic parts in automobile and aerospace industries is due to the fact that it can reduce the structural weight and can lessen the environmental contamination. Among many manufacturing technologies for plastic parts, the injection molding process is very attractive because of its low cost and short production time. Through various analyses of resin flow and molding process for the conventional gate and cooling mechanism, a new type of mold was designed which had different gate location and cooling systems. Newly designed ball seat has an excellent performances, i.e. diminished weld-line, residual stress density, higher magnitude less crack propagation and smaller dimensional contractions effect.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권2호
• /
• pp.52-55
• /
• 2006

The OLEDs(Organic Light-Emitting Diodes) structure organizes the bottom layer using glass, ITO(indium thin oxide), hole injection layer, hole transport layer, emitting material layer, electron transport layer, electron injection layer and cathode using metal. OLED has various advantages. OLEDs research has been divided into structural side and emitting material side. The amount of emitting light and luminescence efficiency has been improved by continuing effort for emitting material layer. The emitting light mechanism of OLEDs consists of electrons and holes injected from cathode and anode recombination in emitting material layer. The mobilities of injected electrons and holes are different. The mobility of holes is faster than that of electrons. In order to get high luminescence efficiency by recombine electrons and holes, the balance of their mobility must be set. The more complex thin film structure of OLED becomes, the more understanding about physical phenomenon in each interface is needed. This paper observed what the thickness change of hole transport layer has an affection through the below experiments. Moreover, this paper uses numerical analysis about carrier transport layer thickness change on the basis of these experimental results that agree with simulation results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.332-337
• /
• 2003

Oxygen-enriched non-premixed flame characteristics was investigated numerically with variation of dilution methods, which are Flue gas recirculation(FGR) and fuel injection recirculation(FIR). In order to compare flamelets in various oxygen-enrichment conditions reasonably, the adiabatic flame temperature and Damkoller number was held fixed by modulating amount of diluents to fuel and oxidizer stream and by varying global strain rate of flame respectively. Also modified GRI 3.0 reaction mechanism was utilized, which was able to predict oxygen-enriched methane flame correctly. Fundamental flame characteristics such as structure, heat release rate and extinction with FGR and FIR were compared in various oxygen enrichment conditions.

• 대한전기학회논문지
• /
• 제39권2호
• /
• pp.111-118
• /
• 1990

This paper presents a new algorithm of contingency analysis and countermeasure to alleviate the line overloads for electric power systems. In this algorithm, the inverse matrix of the new Jacobian matrix when a contingency occurs, in fastly calculated using the house-holder's Inverse Matrix Modification Lamma (IMML) with the original factor table. The generation outputs are firstly adjusted to alleviate all line overloads occurred by the contingency without tripping loads. If the generation adjustment is not enough anymore to alleviate line overloads, then the control of bus injection power is recommended to quickly alleviate remaining overloads with minimum amount of load tripping and generation read-justing at the termination busbars of the overload lines. The proposed algorithm has been validated in tests on the 6 busbar test system.

• 한국연소학회지
• /
• 제22권3호
• /
• pp.23-28
• /
• 2017

The fuel and oxidizer mixing process in the shock tube driven section is simulated numerically. The boundary condition is set based on an shock tube experimental condition. The objective is to predict the gas mixing time for experiments. In the experiment, the amount of fuel to be injected is determined in advance. Then, according to duration of fuel injection, 5 cases with the same fuel mass but different fuel mass flow rate are simulated. After fuel is injected into the driven section, the fuel and air will be mixed with each other through convection and diffusion processes. The mixing time is predicted numerically for experiments.

• 한국통신학회논문지
• /
• 제22권1호
• /
• pp.81-88
• /
• 1997

Wavelength tunable, narrowbandwidth wvelength filters in compound semiconductor have been modeled, fabricated, and characterized. In order to obtain a narrow bandpass characteristics at 1.55.$\mu$m, a highly asymmertrical directional coupler structure composed of a strongly guided ridge waveguide and a weakly guided strip-loaded waveguide was used. The optimized filter structure modeling has been obtained by using the spectral index method, effective index method, and the coupled mode theory. Operation at a center wavelength a 1.537.mu.m with a bandwidth of 1.8nm and transfer efficiency of 50-70% is experimentally achieved. For the purpose of center wavelength tuning, the carrier injection in p-n diode structure has been theoretically investigated. It has been found that the tuning range of nanometer can be easily obtained by moderate amount carrier injection. We also found that the bandwidth becomes broad as the center wavelength tuning increases.

• Carbon letters
• /
• 제16권2호
• /
• pp.86-92
• /
• 2015

Multi-walled carbon nanotube (MWCNT)/polycarbonate (PC) nanocomposite was prepared by direct melt mixing to investigate the effect of the shear rate on the surface resistivity of the nanocomposites. In this study, an experiment was carried out to observe the shear induced orientation of the MWCNT in the polymer matrix using a very simple melt flow indexer with various loads. The compression-molded, should be eliminated. MWCNT/PC nanocomposite sample exhibited lower percolation thresholds (at 0.8 vol%) and higher electrical conductivity values than those of samples extruded by capillary and injection molding. Shear induced orientation of MWCNT was observed via scanning electron microscopy, in the direction of flow in a PC matrix during the extrusion process. The surface resistivity rose with increasing shear rate, because of the breakdown of the network junctions between MWCNTs. For real applications such as injection molding and the extrusion process, the amount of the MWCNT in the composite should be carefully selected to adjust the electrical conductivity.

• 설비공학논문집
• /
• 제7권3호
• /
• pp.353-358
• /
• 1995

The emission characteristics of a semi-Bunsen type burner for gas boilers were studied experimentally. The experimental results reveal that nitric oxide emission increases with fuel flow rate. It is linearly proportional to total fue flow rate at a small amount of fuel up to 0.4 liters per minute. It does not change significantly within the range of fuel flow rate from 0.4 to 1.2 liters per minute per nozzle and increases at large fuel flow rate. The carbon monoxide emission reveals to be dependent upon the fuel flow rate per each nozzle and the number of fuel injection nozzles. Diameter of an injection nozzle could have an effect on the emission characteristics of this type of burners. However, there is no marked change in the nitric oxide emission if the total fuel flow rate is same with different nozzle sizes.