• 센서학회지
• /
• 제5권3호
• /
• pp.65-73
• /
• 1996

수액을 장시간 환자에게 주입할 때 적절한 주입량, 주입률을 조절하는 것이 중요하다. 부적절한 주입량은 환자의 회복에 좋지 않은 영향을 끼칠 수 있으므로 주입량을 감지하는 센서의 신뢰도는 인퓨전 펌프 시스템에 많은 영향을 미친다. 본 연구에서는 인퓨전 펌프 시스템에 사용될 3가지 센서의 성능을 검토하였다. 피에조 필름, 광트렌지스터 및 광 다이오드 어레이의 3가지 센서가 비교되었으며 제안하는 신호 처리 기법과 광 다이오드 어레이를 사용한 기법을 이용하여 간섭과 진동 조도변화 센서의 위치에 따른 감도 변화등의 영향을 줄일 수 있었다. 실험 결과 광 다이오드 어레이가 다른 센서들에 비하여 높은 신지도를 보여 주었다.

• 한국안전학회지
• /
• 제37권4호
• /
• pp.129-138
• /
• 2022

A new method for injecting cooling water into the Korean research reactor (KRR) in the event of beam tube rupture is proposed in this paper. Moreover, the research evaluates the risk to the reactor core in terms of core damage frequency (CDF). The proposed method maintains the cooling water in the chimney at a certain level in the tank to prevent nuclear fuel damage solely by gravitational coolant feeding from the emergency water supply system (EWSS). This technique does not require sump recirculation operations described in the current procedure for resolving beam tube accidents. The reduction in the risk to the core in the event of beam tube rupture that can be achieved by the proposed change in the cooling water injection design is quantified as follows. 1) The total CDF of the KRR for the proposed design change is approximately 4.17E-06/yr, which is 8.4% lower than the CDF of the current design (4.55E-06/yr). 2) The CDF for beam tube rupture is 7.10E-08/yr, which represents an 84.1% decrease compared with that of the current design (4.49E-07/yr). In addition to this quantitative reduction in risk, the modified cooling water injection design maintains a supply of pure coolant to the EWSS tank. This means that the reactor does not require decontamination after an accident. Thermal hydraulic analysis proves that the water level in the reactor pool does not cause damage to the nuclear fuel cladding after beam tube rupture. This is because the amount of water in the chimney can be regulated by the EWSS function. The EWSS supplies emergency water to the reactor core to compensate for the evaporation of coolant in the core, thus allowing water to cover the fuel assemblies in the reactor core over a sufficient amount of time.

• 농업과학연구
• /
• 제34권1호
• /
• pp.37-46
• /
• 2007

본 연구는 사슴뿔이 발생되지 않는 암사슴의 전두골의 뿔 발생예정지역의 좌우 양측골막에 $CaCl_2$ 용액의 주사로 인위적인 뿔 발생유도에 의한 뿔 발생유도율 및 뿔 생산량을 조사하고, 암사슴의 뿔 발생유도가 번식에 미치는 영향을 구명하고자 엘크 암사슴 11두를 공시하여 얻어진 결과는 다음과 같다. 엘크 암사슴에 $CaCl_2$ 처리 농도에 따른 뿔 발생유도는 $CaCl_2$ 30 및 50 % 처리구가 15 % 처리구보다 뿔 발생유도율이 높았으며, 뿔의 생산량에 있어서는 $CaCl_2$ 30 % 처리구가 15 및 50 % 처리구보다 많은 사슴뿔의 생산량을 보였고, $CaCl_2$ 30 % 처리구내 투여량에 있어서는 1.5 ml 및 2.0 ml 투여가 다른 투여수준에 비하여 뿔의 길이와 생산량이 우수 하였다. 암사슴 뿔의 발생유도 후에도 분만율은 75 ~ 100 % 로 번식에는 전혀 영향을 미치지 않는 것으로 판단되었으며, 암사슴의 재생뿔 발생율은 총 11두중 5두가 발생하여 45.0 %로 불규칙한 발생율을 보였다. 이상의 결과에서 $CaCl_2$ 용액 처리에 의한 엘크 암사슴의 뿔 발생유도 및 뿔 생산량에 있어서는 $CaCl_2$ 용액의 농도는 30 %가 적절하고, 투여수준은 1.5 및 2.0 ml 주사시 뿔의 발생유도율 및 생산량을 증대시킬 수 있을 것으로 생각되며, 인위적인 암사슴 뿔의 유도시에도 번식에는 영향을 미치지 않는 것으로 조사되었다.

• Design & Manufacturing
• /
• 제13권2호
• /
• pp.30-36
• /
• 2019

Traditional cell culture(2-dimensional) is the method that provide a nutrient and environment on a flat surface to cultivate cells into a single layer. Since the cell characteristics of 2D culture method is different from the characteristics of the cells cultured in the body, attempts to cultivate the cells in an environment similar to the body environment are actively proceeding in the industry, academy, and research institutes. In this study, we will develop a technology to fabricate micro-structures capable of culturing cells on surfaces with various curvatures, surface shapes, and characteristics. In order to fabricate the hemispheric plastic structure(thickness $50{\mu}m$), plastic preform mold (hereinafter as "preform mold") corresponding to the hemisphere was first prepared by injection molding in order to fabricate a two - layer structure to be combined with a flat plastic film. Then, thermoplastic polymer dissolved in an organic solvent was solidified on a preform mold. As a preliminary study, we proposed injection molding conditions that can minimize X/Y/Z axis deflection value. The effects of the following conditions on the preform mold were analyzed through injection molding CAE, [(1) coolant inlet temperature, (2) injection time, (3) packing pressure, (4) volume-pressure (V/P). As a result, the injection molding process conditions (cooling water inlet temperature, injection time, holding pressure condition (V / P conversion point and holding pressure size)) which can minimize the deformation amount of the preform mold were derived through CAE without applying the experimental design method. Also, the derived injection molding process conditions were applied during actual injection molding and the degree of deformation of the formed preform mold was compared with the analysis results. It is expected that plastic film having various shapes in addition to hemispherical shape using the preform mold produced through this study will be useful for the molding preform molding technology and cast molding technology.

• 산업식품공학
• /
• 제21권2호
• /
• pp.150-157
• /
• 2017

본 연구는 수분함량(40, 50, 60%)과 $CO_2$ 가스 주입(0, 800 mL/min)에 따라 분리대두단백 조직화 압출성형물에 미치는 영향을 알아보기 위하여 이화학적 특성을 분석하였다. 압출성형 공정변수는 사입량 100 g/min, 스크루 회전속도 250 rpm, 사출구 온도 $135^{\circ}C$로 고정하였다. 수분함량이 각각 40, 50%일 때 $CO_2$ 가스 주입량이 0 mL/min에서 800 mL/min으로 증가할수록 직경팽화율과 비길이는 증가하였고 조각밀도는 감소하였다. 하지만 수분함량 60%일 때는 직경팽화율과 비길이는 감소하였고 조각밀도는 증가하였다. $CO_2$ 가스 주입량이 0 mL/min에서 800 mL/min으로 증가할수록 크기가 작은 기공들이 많이 형성되었다. 또한 $CO_2$ 가스 주입량이 0 mL/min에서 800 mL/min으로 증가할수록 수용성질소지수와 수분흡착지수는 증가하였고 조직잔사지수와 조직감은 감소하였다. $CO_2$ 가스 800 mL/min를 주입한 분리대두단백 조직화 압출성형물은 $CO_2$ 가스 0 mL/min을 주입한 분리대두단백 조직화 압출성형물보다 팽화가 잘 일어났으며 단면적이 작은 기공들이 형성되었으나 수용성질소지수와 조직잔사지수, 조직감 분석에서는 최적 조직화에 대한 연구가 더 필요한 것으로 판단되었다.

• 한국분무공학회지
• /
• 제15권2호
• /
• pp.61-66
• /
• 2010

Fuel spray characteristics of the gasoline engine injector has been studied experimentally. To provide fundamental performance data of 4-hole and 12-hole injectors, spray fuel-mass distribution, wall wetting fuel amount and visualization of injectors have been tested and measured with various fuel supply pressure conditions. Spray visualization has been performed to analyze spray formation, spray angle, stream width and penetration length. Test result shows that wall wetting is greatly influenced by the induction air amount and spray atomization. Spray visualization shows that the 12-hole injector has robust performance characteristics with various fuel supply pressure conditions compared with the 4-hole injector. 4-hole injector generates relatively less wall-wetting fuel amount than 12-hole injector does.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.585-590
• /
• 1997

Conventional foaming process has defects such as lower mechanical properties than ur~foaming material due to non-uniform cell distribution and environmental pollution problem caused by chemical blowing agency. So, a new foaming process such as Microcelluar plastics has been introduced to use inactive gases as a foaming agency. In order to apply Microcellular plastics for mass production process system such as extrusion, injection molding and blow molding, it needs to predict the change in material properties of polymer according to the amount of meltingas. In Polymer molding applying Microcelluar plastics, the change of viscosity among several material properties is the most important factor. Therefore, this paper is aimed to establish the method which not only finds out but also predicts the change of viscosity of ABS(Acrylonitri1e Butadiene Styrene) resin according to inert gas amount in extrusion molding.

• 상하수도학회지
• /
• 제18권3호
• /
• pp.392-400
• /
• 2004

This research uses the $TiO_2$/UV process to verify the most suitable condition and possibility to dispose dyeing wastewater that contains pigment and a large amount of pollutants. For this, this research has enforced experiments that compare photo adsorption, photolysis, and photo catalyst oxidation reaction, and also evaluated and analyzed the change of pH and $TiO_2$ dosage, irradiation rates of ultraviolet rays and the dosage change and injection method of $H_2O_2$. According to the results of the dyeing wastewater experiment of storehouse catalyst that uses the new form of $TiO_2$, the photo catalyst oxidation reaction proved to be more effective than photo adsorption and photolysis; 35%, 21% in the case of $TCOD_{cr}$ and 39%, 28% in the case of chromaticity. Taking into consideration the reaction time, amount of photo catalyst reaction and irradiation amount of ultraviolet rays, the decomposition efficiency of pH change proved to be most effective at pH 4. On the whole, the acidity area proved to be effective in dyeing water exclusion than neutral and alkalinity areas. Having evaluated the influence of $TiO_2$ dosage, not only does the decomposition efficiency continuously improve as the $TiO_2$ dosage increases but the shielding effect does not occur also when the $TiO_2$ is at a fixed state. The influence of ultraviolet irradiation amount concluded in the result that as the ultraviolet irradiation amount increases the decomposition efficiency continually increased, but in the case of chromaticity when the irradiation amount was higher than 37.8mW/cm2 the removal efficiency is slowed remarkably. The influence of $H_2O_2$ dosage evaluation reached the results that although the decomposition efficiency increases with the increase of $H_2O_2$ dosage, when above 150mg (total dosage: 1200mg) $H_2O_2$ consumes OH radical itself and reduces the decomposition efficiency. Also in the case of the $H_2O_2$ injection method rather than injecting in the whole amount of $H_2O_2$ (1200mg) needed at the beginning all at once, injecting divided quantities of $H_2O_2$ whenever the electric current density falls below 10mgfl reduces the wases of OH radical due to an excess of $H_2O_2$ and in tum heightens the decomposition efficiency.

• 한방안이비인후피부과학회지
• /
• 제13권2호
• /
• pp.165-181
• /
• 2000

Sinichengpaeum has been widely used in the oriental medical treatment of nasal diseases. These studies were performed done to investigate the effect of Sinicheng- paeum on the anti-allergic action We studied the vascular permeability response induced by the histamine and serotonin injection(allergy Ⅰ type), homologous PCA provoked by the IgE-like antibody against EWA(allergy Ⅳ type), contact dermatitis induced by picryl chloride(allergy Ⅳ type), delayed type hypersensitivity response to SRBC (allergy Ⅳ type), and the amount of eosinophil and IgE. The results were as follows: 1. The effect of Sinichengpaeum on vascular permeability responses to intradermal histamine and serotonin were significant. 2. In the homologous PCA provoked by the IgE-like antibody against white egg albumin, Sinichengpaeum showed a significant effect. 3. In the delayed type hypersensitivity responses to picryl chloride, Sini-chengpaeum provoked a significant effect. 4. After reaction provoked by picryl chloride, Sinichengpaeum showed an insignficant effect on amount of eosinophil, but a significant effect in IgE amount. 5. In the delayed type hypersensitivity responses to SRBC, Sinichengpaeum provoked a significant effect. 6. After reaction provoked by SRBC, Sinichengpaeum showed a significant effect on amount of cosinophil, but an insignificant effect in IgE amount.

• 한국산업융합학회 논문집
• /
• 제5권1호
• /
• pp.75-80
• /
• 2002

In this study, the initial number of bacteria before ozone sterilizing shows 290 per $1m{\ell}$ in RUN 1 and RUN 2 equally, but the removal rate shows more than 50% in RUN 1, and 100% in RUN 2 respectively when ozone injection amount is $0.28mg/{\ell}$. It is regarded as a satisfactory result that E-coli concentration without ozone contact is 890, rapid removal effect of E-coli is observed in $0.28mg/{\ell}$ of ozone, and E-coli is removed perfectly in $0.84mg/{\ell}$ of ozone. It is thought that an excellent efficiency is obtained for vibrio alginolyticus because the initial number of bacteria before ozone contact is positive, but it is altered to negative after ozone contact. CODcr shows the tendency which is somewhat reduced as the ozone injection is increased, but the general effect is appeared not so much, and it is thought that the tendency is caused by the reason that sea water contains much salt which is estimated as a component of CODcr, therefore it is regarded that ozone contact has not an important effect on salinity. It is thought that the frequency of changing salt water in the fish preserve of a sliced raw fish restaurant can be reduced to under the standard because NTU of 7 days after sea water injection is 0.70 in the experiment of turbidity, hut more than 50% of turbidity removal efficiency is appeared at $0.28mg/{\ell}$ of ozone injection, and it shows 70% at $0.84mg/{\ell}$ of ozone injection in RUN 1 and RUN 2 commonly.