• Journal of Korean Academy of Nursing
• /
• v.30 no.1
• /
• pp.122-136
• /
• 2000

Chronic illness requiring attention and management during a long period of time puts great burden onto patients, their family and society. For patients with chronic illnesses, providing social support is the most important, and the fundamental support comes from their spouses. Amount and quality of support from spouses seems to differentiated according to the sex of patients. Female patients tend to believe that their spouses are not very supportive. Therefore, the researchers assessed the burden of husbands of female arthritis patients to discover the factors that result in greater burden. Also, they developed a theoretical model of husbands′ care for their wives through a qualitative research into husbands′ experience. Method 1: The study material was 650 female arthritis patients registered in an arthritis clinic. The questionnaire about the disease experience of female arthritis patients and the burden of husbands were sent. Returned questionnaires numbered 210(32.3%) and 27 were excluded because of inadequate answers. The remaining 183 questionnaires were analyzed. The mean age of the patients was 51 years and the mean age of spouses was 55 years. The mean marital period was 28 years. The average duration since diagnosis was 9.1 years. Education level was varied from primary school to graduate school, and average income/month was 1,517,300 won. Method 2: Initial questionnaire studies on the burden of husbands were performed. Among 183 responding husbands, 23 consented to participate for a qualitative research. Data was obtained by direct and telephone interviews. The mean age of participants was 58 years, and the educational level and socioeconomic status also varied. Result: 1. Husbands′ burden: The average burden was 57.68 with a range of 6-96. 2. Burden and general characteristics: The husband′s burden correlated with the age of the patients, numbers in the family, therapy methods, patient′s level of discomfort, patient′s disease severity, patient′s level of dependence and the husband′s understanding of the level of severity. 3. Linear correlation analysis on burden: The husbands′ burden is explained in 22.5% by husband′s recognition of level of severity and husbands′ age. 4. There were four patterns of the burden on husbands: both objectve burden and subjective burden were high(pattern I), both of objectve burden and subjective burden were low(pattern II), objective burden was high but subjective burden was low(pattern III), objective burden was low but subjective burden was high(pattern IV). The pattern was correlated with the family income, educational level of the patients and their husbands, therapy methods, patient′s level of discomfort, patient′s disease severity, patient′s level of dependence and husband′s understanding of level of severity. 5. The core category of the caring experience of the husbands with arthritis patients was "companionship". The causal factor was the patients′ experience due to symptoms : physical disfigurement, pain, immobility, limitation of house chores, and limitation of social activities. Contextural factors are husbands′ identification of housework and husbands′ concern about the disease. The mediating factors are economic problems, fear of aging, feeling of limitation and family support. The strategy for interaction is mind control and how to solve emotional stress. The "companionship" resulted from caring activities, participation of household activities, helping patients′ to coping with emotional experience. 6. Companionship is established through the process of entering intervention, and caring state of mind. Entering intervention is the phase of participation of therapy and involvement of houseworks. The caring phase consists of decision on therapy, providing therapy, providing direct care, and taking over the household role of wife. Through caring phase, the changing phase set a stage in which husbands consolidate the relationship with their wives, and are reminded of the meaning of marriage. As a result, in changing phase, husbands′ companionship is enhanced. In conclusion, nursing care of chronic illnesses should include a family member especially the spouse. All information on disease shoud be provided to patients and whole family member. Strong support should also be provided to overcome difficulties in taking over role of other sex. Then the quality of life of patients and families will be much improved.

• Composites Research
• /
• v.14 no.3
• /
• pp.18-31
• /
• 2001

Interfacial and microfailure properties of the modified steel, carbon and glass fibers/cement composites were investigated using electro-pullout test under tensile and compressive tests with acoustic emission (AE). The hand-sanded steel composite exhibited higher interfacial shear strength (IFSS) than the untreated and even neoalkoxy zirconate (Zr) treated steel fiber composites. This might be due to the enhanced mechanical interlocking, compared to possible hydrogen or covalent bonds. During curing process, the contact resistivity decreased rapidly at the initial stage and then showed a level-off. Comparing to the untreated case, the contact resistivity of either Zr-treated or hand-sanded steel fiber composites increased to the infinity at latter stage. The number of AE signals of hand-sanded steel fiber composite was much more than those of the untreated and Zr-treated cases due to many interlayer failure signals. AE waveforms for pullout and frictional signals of the hand-sanded composite are larger than those of the untreated case. For dual matrix composite (DMC), AE energy and waveform under compressive loading were much higher and larger than those under tensile loading, due to brittle but well-enduring ceramic nature against compressive stress. Vertical multicrack exhibits fur glass fiber composite under tensile test, whereas buckling failure appeared under compressive loading. Electro-micromechanical technique with AE can be used as an efficient nondestructive (NDT) method to evaluate the interfacial and microfailure mechanisms for conductive fibers/brittle and nontransparent cement composites.

• Journal of agricultural medicine and community health
• /
• v.4 no.1
• /
• pp.41-61
• /
• 1979

Two interview surveys (1976 for 800 patients, 1978 for 200 patients) and an inventory survey through medical records(1978) for epileptic patients who have registered with the Korean Epilepsy Association (Rose Club) since 1971 were carried out by trained health workers in advance of survey. The data obtained from the analysis showed as follows: 1) 35.2% of patients were born in Seoul and 70. 6% of patients born elsewhere have lived in Seoul. 2) 50-60% of patients were 15-30 years cid. 3) 33.4%, 24,6 and 24.6 of all pupils and students went to elementary, junior and senior high schools respectively. 4) 21.2% of all pupils and students had dropped out of school and 51.4% of them were away from school because of epilepsy. 5) 3.1% of all patients had no job at all and students comprised 20.9% of patients followed by clerical work, commercial business and farming with about 6% in each group.6) Reasons given for unemployment such as dismissal (4.3%), quit (27.7%), hesitation to employ (42.5%)and discontinuance of job (25.5%) were basically due to epilepsy. 7) About half(46.2%) of all patients have become Christian since the Rose Club was a voluntary agency which has been sponsored by Christians. 8) 82. 6% of patients were diagnosed as having grand mal as the most. 9) 29.4% of patients explained aura with psychomotor disturbances and 13.8% with sensory disorders. 10) 46.3% of patients were attacked with seizures when they were tired and others(11.6% and 4.9%) after excessive eating and hunger. 11) Patients suffered more seizures in spring and summer rather than in autumn and winter and most patients had attacks 1-5 times a month. 12) For etiologic reasons of epilepsy, 35.5% of patients considered it was caused by psychological stress and 11.5% by trauma. Only 1.1% of patients considered it as having hereditary components. 13) 51% of patients were slow in caring for their own illnesses. They started to reat epilepsy after spending 5 years of time from the initial seizure. Only 5.4% of patients had received the modern anti-epileptic therapy right after the nitial seizure. 14) 62.1% of patients had no therapy or irregular or incomplete treatment before registration at the Rose Club Clinic. 15) Before registration at the Rose Club, 42.4% of patients received medical care. On the other hand, 25.6% went to herb doctors and 12.5% used to go to the drugstore in order to get anti-epileptic drugs. 16) 41. 6% of patients who took anti-epileptic drugs had more or less side-effects. Indigestion was the most common. 17) For continuation of treatment, 30.3% have received treatment for more than 5 years and the evident showed that epilepsy took a longer time to be cured. 18) Regarding the medical care received 44.2% of patients were very satisfied with effective care and 26.5% felt as good. 19) For attitudes toward epilepsy. 27.0% of patients and 68.2% of patients family were pessimistic. 20) 65.9% of patients had optimistic attitudes toward effectiveness of medical care of epilepsy. 21) 64.8% of wives and husbands had better understanding and cooperative for their spouses who had epilepsy. 22) 33.3% of patients were under-treated at the place of work. 23) 70.2% of patients wished to marry when they reach childbearing age and 63% wished to have children. Through the above results it is recommended for nation-wide epilepsy control that the sound and correct health education not only from health aspect but also from welfare aspect should be planned and implemented as soon as possible.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.3
• /
• pp.183-196
• /
• 2017

Objective: The purpose of this research was to assess the agreement between job physical risk factor analysis by ergonomists using ergonomic methods and physical examinations made by occupational physicians on the presence of musculoskeletal disorders of the upper extremities. Background: Ergonomics is the systematic application of principles concerned with the design of devices and working conditions for enhancing human capabilities and optimizing working and living conditions. Proper ergonomic design is necessary to prevent injuries and physical and emotional stress. The major types of ergonomic injuries and incidents are cumulative trauma disorders (CTDs), acute strains, sprains, and system failures. Minimization of use of excessive force and awkward postures can help to prevent such injuries Method: Initial data were collected as part of a larger study by the University of Utah Ergonomics and Safety program field data collection teams and medical data collection teams from the Rocky Mountain Center for Occupational and Environmental Health (RMCOEH). Subjects included 173 male and female workers, 83 at Beehive Clothing (a clothing plant), 74 at Autoliv (a plant making air bags for vehicles), and 16 at Deseret Meat (a meat-processing plant). Posture and effort levels were analyzed using a software program developed at the University of Utah (Utah Ergonomic Analysis Tool). The Ergonomic Epicondylitis Model (EEM) was developed to assess the risk of epicondylitis from observable job physical factors. The model considers five job risk factors: (1) intensity of exertion, (2) forearm rotation, (3) wrist posture, (4) elbow compression, and (5) speed of work. Qualitative ratings of these physical factors were determined during video analysis. Personal variables were also investigated to study their relationship with epicondylitis. Logistic regression models were used to determine the association between risk factors and symptoms of epicondyle pain. Results: Results of this study indicate that gender, smoking status, and BMI do have an effect on the risk of epicondylitis but there is not a statistically significant relationship between EEM and epicondylitis. Conclusion: This research studied the relationship between an Ergonomic Epicondylitis Model (EEM) and the occurrence of epicondylitis. The model was not predictive for epicondylitis. However, it is clear that epicondylitis was associated with some individual risk factors such as smoking status, gender, and BMI. Based on the results, future research may discover risk factors that seem to increase the risk of epicondylitis. Application: Although this research used a combination of questionnaire, ergonomic job analysis, and medical job analysis to specifically verify risk factors related to epicondylitis, there are limitations. This research did not have a very large sample size because only 173 subjects were available for this study. Also, it was conducted in only 3 facilities, a plant making air bags for vehicles, a meat-processing plant, and a clothing plant in Utah. If working conditions in other kinds of facilities are considered, results may improve. Therefore, future research should perform analysis with additional subjects in different kinds of facilities. Repetition and duration of a task were not considered as risk factors in this research. These two factors could be associated with epicondylitis so it could be important to include these factors in future research. Psychosocial data and workplace conditions (e.g., low temperature) were also noted during data collection, and could be used to further study the prevalence of epicondylitis. Univariate analysis methods could be used for each variable of EEM. This research was performed using multivariate analysis. Therefore, it was difficult to recognize the different effect of each variable. Basically, the difference between univariate and multivariate analysis is that univariate analysis deals with one predictor variable at a time, whereas multivariate analysis deals with multiple predictor variables combined in a predetermined manner. The univariate analysis could show how each variable is associated with epicondyle pain. This may allow more appropriate weighting factors to be determined and therefore improve the performance of the EEM.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.23 no.3
• /
• pp.746-763
• /
• 1996

An alternative design to conventional class II cavity preparation for proximal carious lesions is the tunnel preparation. It preserves the marginal ridge intact, thus making it possible to maintain the natural contact relationship with the adjacent tooth and minimize tooth reduction. This in vitro study was purposed to evaluate the effect of the materials' elastic constants and shear-bond strength on the marginal ridge fracture resistance of teeth restored by the tunnel technique, and to find the materials of choice for tunnel restorations. $Resinomer^{(R)}$, $Ketac-silver^{(R)}$, $Miracle-Mix^{(R)}$, and Tytin were used as restorative material. The elastic constants of each restorative material were evaluated by ultrasonic pulse measurement. Young's modulus and bulk modulus of the restorative materials were evaluated in three specimens for each material type. The shear-bond strength of the restorative materials to the dentin surface was measured after thermocycling 400 times between 6 and $60^{\circ}C$, using ten specimens for each material type. For measuring marginal ridge strength, 60 sound extracted molar teeth were distributed into six groups by size. Sound molar teeth were used as a Control group and unfilled prepared teeth were grouped as Unrestored. Another four groups were named Resinomer group, Ketac-Silver group, Miracle Mix group, and Tytin group by type of restorative material. Tunnel cavity preparation was done with ' 1/2, 2, and 4 round burs in sequence. Initial access to proximal surface was made through an occlusal access preparation started at least 2mm from the marginal ridge, and the proximal opening was formed about 2.5mm below the marginal ridge. After restoration and thermocycling, marginal ridge strength was measured using a universal testing machine. The results were as follows: 1. The Young's modulus of $Tytin^{(R)}$ was 63.95 GPa, followed by $Ketac-Silver^{(R)}$ 27.60 GPa, $Miracle-mix^{(R)}$ 18.48 GPa, and $Resinomer^{(R)}$ 10.74 GPa showing significant differences between the groups(P<0.05). The bulk modulus of the materials showed the same order as Young's modulus. The value of $Tytin^{(R)}$ showed 59.57 GPa indicating that it will deform less than other materials under the same stress. It was followed by $Ketac-Silver^{(R)}$ 23.57 GPa, Miracle $Mix^{(R)}$ 12.50 GPa, and $Resinomer^{(R)}$ 11.60 GPa. 2. The Resinomer group had a shear-bond strength of 7.41 MPa which was significantly higher than those of the Ketac-Silver group (1.80 MPa) and the Miracle Mix group (2.84 MPa) (P<0.01). All the specimens of Tytin group detatched from the dentin surface during thermocycling. 3. The mean marginal ridge strength of the Unrestored group(46.14 kgf) was significantly lower than that of the Control group (84.24 kgf) (P<0.01). The marginal ridge strength of teeth restored by the tunnel technique was, in order, Ketac-Silver group 74.06 kgf, Miracle Mix group 73.36 kgf, Resinomer group 63.47 kgf, and Tytin group 58.76 kgf. The Ketac-Silver, Miracle Mix, and Resinomer groups showed no significant difference with the Control group (P>0.05), but the Tytin group showed significantly lower strength compared to the Control group(P<0.05). The results showed that the marginal ridge strength of the teeth restored by the tunnel technique was not significantly lower than that of sound teeth. They also demonstrated that the bonding strength of the restorative material to the tooth surface should be high and the modulus of elasticity should not be lower than that of the tooth in order to restore the marginal ridge strength to its natural condition.

• Restorative Dentistry and Endodontics
• /
• v.32 no.2
• /
• pp.130-137
• /
• 2007

This in vitro study examined the effect of surface defects on cutting blades on the extent of the cyclic fatigue fracture of HEROShaper Ni-Ti rotary files using fractographic analysis of the fractured surfaces. A total of 45 HEROShaper (MicroMega) Ni-Ti rotary flies with a #30/.04 taper were divided into three groups of 15 each. Group 1 contained new HEROShapers without any surface defects. Group 2 contained HEROShapers with manufacturing defects such as metal rollover and machining marks. Croup 3 contained HEROShapers that had been clinically used for the canal preparation of 4-6 molars A fatigue-testing device was designed to allow cyclic tension and compressive stress on the tip of the instrument whilst maintaining similar conditions to those experienced in a clinic. The level of fatigue fracture time was measured using a computer connected the system. Statistical analysis was performed using a Tukey's test. Scanning electron microscopy (SEM) was used for fractographic analysis of the fractured surfaces. The fatigue fracture time between groups 1 and 2, and between groups 1 and 3 was significantly different (p<0.05) but there was no significant difference between groups 2 and 3 (p>0.05). A low magnification SEM views show brittle fracture as the main initial failure mode At higher magnification, the brittle fracture region showed clusters of fatigue striations and a large number of secondary cracks. These fractures typically led to a central region of catastrophic ductile failure. Qualitatively, the ductile fracture region was characterized by the formation of microvoids and dimpling. The fractured surfaces of the HEROShapers in groups 2 and 3 were always associated with pre-existing surface defects. Typically, the fractured surface in the brittle fracture region showed evidence of cleavage (transgranular) facets across the grains, as well as intergranular facets along the grain boundaries. These results show that surface defects on cutting blades of Ni-Ti rotary files might be the preferred sites for the origin of fatigue fracture under experimental conditions. Furthermore this work demonstrates the utility of fractography in evaluating the failure of Ni-Ti rotary flies.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.35 no.6
• /
• pp.595-600
• /
• 2002

Comparison of blood properties in juvenile black seabream (Acanthopans schlegeli) between transfer from seawater to freshwater (sFW) and transfer from freshwater to seawater (fSW) were investigated for 60 days. Plasma cortisol levels in sFW were significantly increased from 34.2 $\pm$ 28.6 ng/mL at the beginning to 365.6 $\pm$ 136.0 ng/mL at 3 hours, and decreased to the beginning level at 24 hours. However, in fSW, no significant differences in the cortisol levels were recognized throughout experimental period. No significant difference was found in the glucose levels between sFW and fSW. The transfer from seawater to freshwater of juvenile black seabream resulted in reduced $Na^{+}\;and\; Cl^{-}$ concentrations for 24 hours (decreasing from 165.3 $\pm$ 2.5, 146.0$\pm$ 2.2 to 118.3 $\pm$ 12.3, 78.0$\pm$ 7.0 mEq/L, respectively), but these were completely recovered the beginning levels at 30 days. Total protein and AST showed no significant differences between the two rearing conditions, while ALT was markedly elevated at 3 hour in sFW and at 24 hours in fSW. Ht in sFW was increased from 18.5 $\pm$ $0.6\%$ at the beginning to 25.3 $\pm$ $4.0\%$ at 12 hours, and was decreased to the beginning level at 24 hours. Ht, RBC and Hb in fSW were also significantly higher at 12 hours, but recovered to their initial levels at 24 hours. All fish were dead until 50 days in sFW while survival rate in fSW was $85\%$ at the end of experiment.

• The Korean Journal of Petroleum Geology
• /
• v.2 no.2 s.3
• /
• pp.59-70
• /
• 1994

The Cenozoic geological structures and the tectonic evolution of the southern Ulleung Basin were studied with seismic profiles and exploration well data. Basement structure of the Korea Strait is distinctly characterized by normal faults trending northeast to southwest. The normal faults of the basement are most likely related to the initial liking and extensional tectonics of Ulleung Basin. Tsushima fault along the west coast of Tsushima islands runs northeastward to the central Ulleung Basin. The Middle Miocene and older sequences in the Tsushima Strait show folds and faults mostly trending northeast to southwest. These folds and faults may be interpreted as a result of compressional tectonics. The Late Miocene to Qauternary sequences are not much deformed, but numerous faults mostly N-S trending are dominated in the Tsushima Strait. The Ulleung Basin was in intial rifting during Oligocene, and then active extension and subsidence from Early to early Middle Miocene. Therefore SW Japan separated from Korea Peninsula and drifted toward southeast, and Ulleung Basin was formed as a pull-apart basin under dextral transtensional tectonic regime. During rifting and extensional stage, Tsushima fault as a main tectonic line separating SW Japan block from the Korean Peninsula acted as a normal faulting with right-lateral strike-slip motion as SW Japan drifted southeastward. During middle Middle Miocene to early Late Miocene, the opening of Ulleung basin stopped and uplifted due to compressional tectonics. The southwest Japan block converging on the Korean Peninsula caused compressional stress to the southern margin of Ulleung Basin, resulting in strong deformation under sinistral transpressional tectonic regime. Tsushima fault acted as thrust fault with left-lateral strike-slip motion. From middle Late Miocene to Quaternary, the southern margin of Ulleung Basin has been controlled by compressional motion. Thus the Tsushima fault still appears to be an active thrust fault by compressional tectonic regime.