• 대한기계학회논문집B
• /
• 제22권8호
• /
• pp.1064-1072
• /
• 1998

The evaporation of sludge particles in a sludge dryer has been numerically investigated with commercial CFX4.1 code. Gas flow field, gas temperature field, sludge particle trajectories, and the moisture content variation of sludge particles are calculated fort various influencing factors, i. e., gas swirl velocity, initial particle distribution, gas temperature. Evaporation of sludge particles increases with gas swirl velocity, several supplying positions, and gas temperature, respectively due to increased residence time, increased contacting surface area, and increased temperature difference between gas and particle.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.67-75
• /
• 2002

A study to investigate the influence of combustion chamber shape, especially piston top face configuration, on the combustion stability is presented with CFD analysis and single cylinder GDI engine test. Initial configuration of the piston bowl was designed with CFD analysis and further parametric studies of the design factors on the piston top face were carried out through the single cylinder GDI engine test. It was found that both the geometry of piston top face and the compression ratio have great influences on the combustion stability. Of interest is that the design factors of the GDI piston to prevent mixture diffusion out of the piston bowl have important roles for the stable combustion at the stratified mixture condition. Also the relationship between spray impingement and flow pattern in a GDI piston bowl should be considered to design an optimal bowl configuration for stable stratified combustion.

• 정보학연구
• /
• 제8권2호
• /
• pp.85-91
• /
• 2005

We studied a pollution mechanism for simulation of contamination environment in industrial concentrated area of around a metropolitan that made to circulated flow in the chamber. In case of the virgin both side of EPDM or Silicon insulator, we confirmed that the pollution to much more than service insulator in the field. Also contamination of initial state of the virgin didn't falling in spite of physical outside factor easily. This study confirmed to that the silicon was too much accumulated pollution contrast to EPDM insulator from scatter(spray) point to regular interval position use the Kaolin contaminant in the chamber. There are effected to the hydrophobicity of polymer insulator due to the pollution. In ceramic insulator, we get to know that pollution is much more at the Post insulator with vertical than with horizontal setup insulator.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2007년도 추계학술대회 및 제23회 정기총회
• /
• pp.200-201
• /
• 2007

The present study was conducted in three fields at Namhae to examine the removal efficiency of organic free, heavy metal immobilized sediment on Cochlodinium polykrikoidesand and on sea water quality. The present study results concluded that removal efficiency was depends on the initial number of red tide cells. There was no drastic change in the sea water quality after sediment spray. For the comparison of effectiveness of betonite, zeolite and lime were mixed with sediment did not show any marked difference in removal. Finally, the present study evaluated 50g/$m^{2}$ sediment is sufficient to remove 100% cells density, even though various environmental factors are interfering the mechanism.

• 전기학회논문지
• /
• 제60권10호
• /
• pp.1935-1940
• /
• 2011

The control logic of steam temperature was redesigned, tested and applied to the power plant after its steam temperature equipments had been revised. This power plant use the ancillary gas gotten in the process of making iron in the steel mill. The boiler of power plant has the superheater and reheater to make the superheated steam. The superheater and reheater have the spray valve to control their temperature. The reheater has the gas bypass damper additionally in this plant. The control logics were redesigned in cascade forms and the initial parameters of control logics were calculated from the several step tests. The final parameters could be obtained through the several repeated tests and the feedforward functions were added by temperature deviation and air flow. The power plant is being commercially-operated normally by improved control logics and It is expected that this improved controls help the efficiency improvement and safe operation of plant.

• 오토저널
• /
• 제15권1호
• /
• pp.37-44
• /
• 1993

Fuel injection system is an important tool in the exhaust emission and performance of a diesel engine. Effects of the fuel injection system in diesel combustion was investigated experimentally by measuring the performance and analyzing the combustion phenomena in a D.I. diesel engine. The selected injection parameters were nozzle opening pressure, nozzle projection length, and nozzle spray angle. From the measured results, it is shown that the fuel injection pipe diameter is an effective means to improve engine performance in a middle and high speed range and the 2 stage spring nozzle holder has the advantage of increasing the engine performance due to the initial injection pressure in a low speed range. It has been also shown that increasing nozzle opening pressure resulted in decrease in smoke, but increase in NO$_{x}$ from the engine.e.

• Journal of Korean Neurosurgical Society
• /
• 제37권4호
• /
• pp.303-306
• /
• 2005

In cases of brain or other organ abscess, the causative etiology or disease are not always definable. We report a case of brain, renal, and possibly lung abscesses in a middle aged woman. After close, stepwise surveillance of possible etiologic factors, we covered out a small solitary pulmonary arteriovenous fistula without any pulmonary symptoms and successfully occluded the fistula via endovascular approach. The congenital pulmonary arteriovenous fistula should be bear in mind as a cause of repeated, multiple systemic infective source spray and be pursued despite of negative initial baseline studies.

• 한국분무공학회지
• /
• 제16권4호
• /
• pp.186-194
• /
• 2011

This study performed the numerical analysis of the internal nozzle flows including cavitation phenomena by using the automated body-fitted grid generator and the multi-fluid model. The effect of grid refinement and the validation of multifluid model were investigated using four computational meshes under two test conditions. The mesh #3 was chosen as the optimum which can reduce the computational time and have good prediction ability to identify the cavitation region simultaneously. In addition, the computed results using multi-fluid model were compared with the reference experimental observations and numerical simulation results using homogeneous equilibrium model. From the distribution of volume fraction and velocity field, the multi-fluid model predicted the internal nozzle flows well when the liquid quality parameters were selected as $1.0{\times}10^{12}$ for initial number density and 25 ${\mu}m$ for bubble diameter.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.170-171
• /
• 2014

The buildings constructed with steel structure is coated with certified fire resistive material to resist from fire. Coating materials lose their initial performances as time passes, so they need some maintenance. This study is covers standardization of the methods for assessing the durability of SFRM. In Korea, more than 90 percent of SFRM are used indoors. So This study is to decide proper test method through investigation and examination of effect factor to performance of fire-resistant structure and applicable test method.

• 한국분무공학회지
• /
• 제25권2호
• /
• pp.68-73
• /
• 2020

In the present study, experiments on the film boiling of liquid droplets on oxidized copper surface was conducted. The shape of pure water droplets was observed, and the evaporation rate of them was measured during the film boiling evaporation process. The droplet of initial volume 16 ~ 30 µl was applied onto the oxidized copper surface heated up to 300 ~ 500℃, then the shape of the droplet was analyzed during the film boiling evaporation. Experimental results showed that there was good correlation between dimensionless volume and dimensionless time. However, a significant difference in evaporation rate for small and large droplets discussed in previous study was not found.