• 한국농공학회지
• /
• 제41권2호
• /
• pp.80-91
• /
• 1999

This paper presents the stress-strain , volumetric strain characteristics of the Pocheon weathered residual granite soil with variation of the initial water content under drained conditions. A series of consolidated drained triaxial compressiion tests and isotrpc compression tests with various initial water content on specimens were performed. All material parameters of Lade's double work hardening model were determined by using the results of tests. Most aspects of the soil behavior measured in the triaxial compression tests were reproduced with good accuracy by the constitutive model . Therefore double work hardening model has been shown to be applicable to weathered residual granite soil.

• 한국방재학회 논문집
• /
• 제9권2호
• /
• pp.11-15
• /
• 2009

본 논문에서는 균일 모멘트 하중을 받는 박판 아치의 탄성 좌굴에 관한 연구를 수행하였다. 초기 곡률을 고려한 비선형 변형률-변위 관계식을 전체 포텐셜 에너지 방정식의 이차 변분에 대입하여 초기 곡률 효과를 포함하는 에너지 방정식을 유도하였다. 휨 모멘트에 의한 단면 내 법선 변형률이 선형으로 분포한다는 초기 곡률 효과에 대한 가정사항을 유도과정에 일관되게 적용하였다. 균일 모멘트 하중을 받는 아치의 휨-비틀림 좌굴하중에 관한 제차해를 제시하고 타 연구자의 결과와 비교하였다.

• Geomechanics and Engineering
• /
• 제21권6호
• /
• pp.527-536
• /
• 2020

An elastic-plastic solution for cavity expansion problem considering strength degradation, undrained condition and initial anisotropic in-situ stress is established based on the Tresca yield criterion and cavity expansion theory. Assumptions of large-strain for plastic region and small-strain for elastic region are adopted, respectively. The initial in-situ stress state of natural soil mass may be anisotropic caused by consolidation history, and the strength degradation of soil mass is caused by structural damage of soil mass in the process of loading analysis (cavity expansion process). Finally, the published solutions are conducted to verify the suitability of this elastic-plastic solution, and the parametric studies are investigated in order to the significance of this study for in-situ soil test.

• 한국지반환경공학회 논문집
• /
• 제19권12호
• /
• pp.47-58
• /
• 2018

Duncan & Chang(1970)는 던컨-창 모델을 제안하면서 흙시료의 초기 접선계수와 극한 축차응력을 구하기 위하여 쌍곡선이론을 사용하여 삼축압축시험의 응력-변형률의 비선형관계를 변환된 변형률/축차응력-변형률의 선형관계로 재구성하였다. 그러나 변환된 응력-변형률 관계는 이론적으로 선형관계를 나타내지만, 실제로는 시험이 시작되는 변형률이 작은 구간과 시료가 파괴에 이르는 변형률이 큰 구간에서는 비선형관계를 보인다. 이러한 현상은 삼축압축시험의 응력-변형률 곡선이 완전한 쌍곡선 형태가 아님을 나타낸다. 따라서 변환된 응력-변형률 곡선의 전 구간에 대하여 선형 회귀분석을 실시하여 직선의 식을 구하게 되면, 비선형관계를 나타내는 구간의 범위에 따라 선형관계식의 산정에 편차가 발생하게 된다. 이러한 편차를 줄이기 위하여 본 연구에서는 변환응력-변형률 관계에서 비선형을 나타내는 초반과 종반 구간을 제외한 구간에 대하여 선형회귀분석을 실시함으로써 초기접선계수와 극한 축차응력을 산정하는 수정회귀분석법을 제안하였다. 수정회귀분석법을 검증하기 위하여, 풍화토의 다짐시료에 대하여 압밀-배수 삼축압축시험을 실시하였다. 삼축압축시험의 응력-변형률 곡선으로부터 구한 변환응력-변형률 관계에 대해서 수정회귀분석을 실시하여 Duncan et al.(1980)이 제안한 2점법으로 구한 결과와 비교하였다. 분석결과 수정회기분석법에 비해 Duncan의 2점법으로 산정한 초기 접선계수는 4.0% 크게, 그리고 극한 축차응력은 2.9% 작게 평가되었다.

• Structural Engineering and Mechanics
• /
• 제11권5호
• /
• pp.519-534
• /
• 2001

The effect of the initial imperfections on the nonlinear behaviors and ultimate strength of the thin-walled members subjected to the axial loads, obtained by the finite element stability analysis, are examined. As the initial imperfections, the bucking mode shapes of the members are adopted. The buckling mode shapes of the thin-walled members are obtained by the transfer matrix method. In the finite element stability analysis, isoparametric degenerated shell element is used, and the geometrical and material nonlinearity are considered based on the Green Lagrange strain definition and the Prandtl-Reuss stress-strain relation following the von Mises yield criterion. The U-, box- and I-section members subjected to the axial loads are adopted for numerical examples, and the effects of the initial imperfections on the nonlinear behaviors and ultimate strength of the members are examined.

• Journal of Mechanical Science and Technology
• /
• 제16권12호
• /
• pp.1594-1603
• /
• 2002

In this paper, when the initial propagation angle of a branched crack is calculated from the maximum tangential stress criterion (MTSC) and the minimum strain energy density criterion (MSEDC), it is essential that you use stress components in which higher order terms are considered and stress components at the position in a distance 0.005㎜ from the crack tip (=r). When an interfacial crack propagates along the interface at a constant velocity, the initial propagation angles of the branched crack are similar. to the mode mixities (phase angle) and the theoretical values obtained from MTSC and MSEDC. The initial propagation angle of the branched crack depends considerably on the stress intensity factor K$_2$.

• 한국자동차공학회논문집
• /
• 제5권4호
• /
• pp.207-218
• /
• 1997

A new blank design method is introduced to predict the blank shape and the strain distribution in the sheet metal forming process. This method deals with only one step from the final shape to the initial blank using the ideal forming theory. Based on this theory, a three-dimensional membrane finite element code has been developed to design an initial blank in the sheet metal forming process. In this paper, the designs of initial blanks for forming a cylindrical cup, a rectangular cup, and a front fender are presented as examples. Also, it compares the two shapes, the target shape with the shape which is deformed from the initial blank using the FEM analysis code. The results illustrate the information that this direct design code is useful in the preliminary design state.

• Journal of Biosystems Engineering
• /
• 제15권3호
• /
• pp.219-229
• /
• 1990

The compression creep behavior of grains when loaded depends not only on load but also on duration of load application. The most common methods of studying the load-time characteristics of agricultural products is by employing rheological models such as Burger's model. However it is sometimes not sufficient to describe the viscoelastic behavior of grains to be Burger's model. For this reason, this study was conducted to develop the rheological model which represented the creep compliance response of the rough rice kernel and was a function of initial stress applied and time. The effects of the initial stress applied and the moisture content on the compression creep behavior of the rough rice kernel were analyzed. The results were obtained from the study as follows: 1. Since the viscoelastic behavior of the rough rice kernel was nonlinear, the transient and steady state creep compliance was satisfactorily modelled as follows: $$J({\sigma},t)=A{\sigma}^B[C+Dt-exp(-Ft)]$$ But, for the every stress applied, the compression creep behavior of the samples tested can be well described by Burger's model respectively. 2. The creep compliance, the instantaneous elastic strain, the retarded elastic strain and the viscous strain of the sample tested generally increased in magnitude with increasing the applied initial stress and the moisture content used in the tests. At low moisture content, the creep compliance for the Japonica-type rough rice kernel Was a little higher than those for Indica-type and at high moisture content, vice versa at high moisture content. 3. The retardation times of the samples had not an uniform tendency by the initial stress and the moisture content. The retardation times ranged from 0.66 to 6.76 seconds, and the creep progressed from transient to steady state at a relatively high rate. 4. The less viscous strain than the instantaneous elastic strain for the samples tested indicated that rough rice kernel behaved as a viscoelastic body characterized by elasticity than viscosity.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.224-231
• /
• 2021

Recently, the waterproofing performance of high-voltage connectors in automotive vehicles has attracted increased interest. In this study, an optimal cross-sectional shape was derived to obtain uniform contact pressure and strain by considering stress relaxation problems caused by initial tension when mounting a seal. A high strain of 52.1 was distributed in the round region, owing to excessive initial tension. The finite element method (FEM) analysis indicated that the strain corresponding to the optimal initial tensile was 11. We adopted six design factors to optimize the seal cross-section and three factors as the main design factors. An orthogonal arrangement table was prepared using Minitab. FEM analyses of 16 study models were conducted to determine the optimized model. The contact pressure of the optimization model is the most evenly distributed while satisfying the waterproof performance of 0.47 MPa. Compared to the initial model, the difference in strain decreases from 35.5% to 19.6%. Finally, the derived cross-sectional shape can reduce the strain of the round region by 33.8% and the differences in the contact pressure at the upper and lower surfaces by 42% and 76%, respectively.

• 산업기술연구
• /
• 제21권B호
• /
• pp.331-339
• /
• 2001

Zero to tension fatigue tests and strain controlled fatigue tests were carried out to find how initial strain induced martensite, ${\alpha}^{\prime}$ affects low and high cycle fatigue behavior and fatigue crack growth mechanisms. Microscopic study and phase analysis were carried out with TEM, SEM, EDAX, Optical Microscope, Ferriscope, and X-ray diffractometry. The amount of Initial ${\alpha}^{\prime}$ was controlled from 0% to 33% by controlling the temperatures for cold working and heat treatment. Lower contents of initial ${\alpha}^{\prime}$ showed higher fatigue resistance in low cycle fatigue but lower fatigue resistance in high cycle fatigue because it is ascribed to the more transformation of ${\alpha}^{\prime}$ martensite during low cycle fatigue and higher ductility. In high cycle fatigue, fatigue life is attributed to the strength and phase transformation of austenite into ${\alpha}^{\prime}$ during fatigue was negligible. ${\gamma}$ boundary, ${\gamma}/twin$ boundary, and ${\gamma}/{\alpha}^{\prime}$ boundary were found to be the preferred site of fatigue crack initiation.