• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.914-921
• /
• 2014

In this paper, an algorithm is suggested to detect an offset angle of the absolute rotor position sensor after the initial assembly of a PMSG. Unlike previous studies in a stationary state, this one is not designed to detect an electrical angle but rather the absolute position of the rotor is detected while operating the generator. Also,a position sensor, current sensors and voltage sensor were used to ensure reliability. This technique completes the detection of the sensor offset in two steps. In the first step, a zero-crossing of the EMF is measured using a voltage sensor to detect the electrical angle offset when the alternator is actuated by the engine. In the second step, a high frequency current is injected along the d-axis on-line during the control of the generation, eventually to obtain the inductance using a DFT (Discrete Fourier Transform), and then to ultimately extract the final electrical angle offset through the comparison of the inductance magnitude. The suggested algorithm was validated with PSIM simulation and, furthermore, was tested with actual experiments on a dynamometer.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1161-1164
• /
• 2002

The position information of the rotor are required while the SRG(Switched Reluctance Generator) is drived. The position information is generally provided by shaft encoder or resolver. But it is weak in the dusty, high temperator and EMI environment. Therefore, It is required for the sensor to be eliminated from SRG. In this paper, a estimation algorithm for the rotor position of the SRG is introducted and a constant DC-link voltage is controled by PID controller. The estimation algorithm is imple--mened by using the instantaneous flux profile, and the initial position is estimated by injecting high frequency pulse voltage. It is proved that the rotor position is esti--mated very well by the exeriments.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.2
• /
• pp.752-760
• /
• 2018

In this paper, interior permanent magnet synchronous motor (IPMSM) design for sensorless drive, considering magnetic neutral point shift according to magnetic saturation, has been proposed. Sensorless control was divided into a method based on inductance and a method based on back induced voltage. Because induced voltage is very small at zero or low speed, error in rotor initial position estimation may occur. Using the ratio of saliency addresses this problem. When using high-frequency injections at low speed, the rotor's initial position is estimated at the smallest portion of the inductance. IPMSM has the minimum inductance at the d-axis. However, if magnetic saturation leads to magnetic neutral point variation, following the load current change, there is a change in the minimum point of inductance. In this case, it can lead to failure of initial rotor position estimation. As a result, it is essential that the blocking design has an inductance minimum point shift. As such, in this study, an IPMSM design method, by blocking magnetic neutral point change, has been proposed. After determining the inductance profile based on the finite element analysis (FEA), the results of proposed method were verified.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.5
• /
• pp.440-446
• /
• 2006

The magnitude of output torque in a BLDC Motor depends on torque angle so that the exact initial position of rotor is essentially required for good starting. This paper presents a novel starting control method for smooth starting in a position-sensorless controlled BLDC motor drive for reciprocating compressor of refrigerator. The proposed method starts a BLDC motor using information on the initial position of rotor, determined from current response characteristics, and shows robust starting capability to starting load variations. The effectiveness of the proposed method is verified through experimental results.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.96-98
• /
• 2009

This paper propose a method to detect the rotor position of IPMSM(Interior permanent magnet synchronous motor) at standstill without a position sensor. The proposed method is based on current variation caused by the magnetic saturation of stator core as rotor position. By choosing an appropriate voltage vector and applying it to phase winding, it enables the algorithm to discern between a north pole and south pole, and subsequently estimates an absolute position. This method dose not depend on the model of the motor and the motor parameter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.5
• /
• pp.349-356
• /
• 2021

Permanent magnet synchronous motors are mainly used in the traction of electric vehicle and home application products including air-conditioners and refrigerators. For sensorless control without rotor position sensors, I-F control is applied for initial starting at low speeds, and mode is changed to sensorless control when the rotor speed is sufficiently accelerated for estimating rotor position. When the mode is changed to the sensorless control from the open-loop starting, the initial integral value of the speed controller should be considered by load condition; otherwise, the transition to sensorless control may fail. The sensorless transfer algorithm of PM synchronous motor based on load condition for smooth transition is proposed. The performance of the proposed sensorless transfer algorithm was verified by experiments.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.646-650
• /
• 2004

This paper presents a novel method to detect the rotor position of the BrushLess DC(BLDC) motor at standstill and a start-up method to accelerate the rotor up to a certain speed where the conventional position sensorless control methods based on the back EMF could work reasonably The proposed initial rotor position estimation method is suitable to avoid the temporary reverse rotation or the starting failure. This method can be implemented using only one current sensor at DC link of the inverter. It does not depend on the model of the motor , and it is robust to motor parameter variations. By the proposed method, it is demonstrated experimentally that a stable starting can be achieved even with severe mechanical disturbance.

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.119-122
• /
• 2003

This paper describes the sensorless technique for the surface-mounted permanent-magent synchronous motor(SPMSM or PMSM) drive based on magnetic saliency. The control technique is a sensorless control algorithm that injects the high frequency voltage to the stator terminal in order to estimate the rotor position and speed. The rotor position and speed for sensorless vector control is achieved by appropriate signal processing to extract the position information from the stator current in the low speed range including zero speed. Proposed sensorless algorithm using the double-band hysteresis controller and initial rotor position detection exhibits excellent reference tracking and increased robustness. Experimental results are presented to verify the feasibility of the proposed control schemes.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1515-1527
• /
• 2018

This paper presents a sensorless speed control of IPMSM (Interior Permanent Magnet Synchronous Motor) using the high-frequency (HF) square wave injection method. In the proposed HF pulsating square wave injection method, injection voltage is applied into the estimated d-axis of rotor and high-frequency induced q-axis current is considered to estimate the rotor position. Conventional square wave injection methods may need complex demodulation process to find rotor position, while in the proposed method, an easy demodulation process based on the rising-falling edge of the injected voltage and carrier induced q-axis current is implemented, which needs less processing time and improves control bandwidth. Unlike some saliency-based sensorless methods, the proposed method uses maximum torque per ampere (MTPA) strategy, instead of zero d-axis command current strategy, to improve control performance. Furthermore, this paper directly uses resultant d-axis current to detect the magnet polarity and eliminates the need to add an extra pulse injection for magnet polarity detection. As experimental results show, the proposed method can quickly find initial rotor position and MTPA strategy helps to improve the control performance. The effectiveness of the proposed method and all theoretical concepts are verified by mathematical equations, simulation, and experimental tests.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1004-1010
• /
• 2020

This paper proposes an initial rotor magnetic pole detection method for single-phase permanent magnet synchronous motors. The target motor cannot obtain position information based on the back emf in the low speed and stop state. Therefore, an open loop starting process is required, and in this process, initial rotor position information for low current and soft start is need. The proposed initial rotor magnetic pole detection algorithm considers the effect of asymmetric air- gap and magnetic flux. In addition, the high-frequency voltage signal injection and the offset voltage for accurate detection is used. As a result, the permanent magnet poles are is determined by acquiring the maximum value of the induced current using the virtual dq-axis.