• Elastomers and Composites
• /
• 제44권1호
• /
• pp.47-54
• /
• 2009

본 연구에서는 다양한 종류의 보강제를 혼합한 EPDM 컴파운드의 원적외선에 의한 가교 반응을 조사하였다. 보강제가 원적외선에 의한 가교 반응에 미치는 영향을 평가하기 위하여 컴파운드의 발열 온도 및 DSC 분석에 의한 가교도를 측정하였으며, 특히 원적외선에 의한 가교 특성을 비교하기 위하여 동일 조건에서 열풍에 의한 가교 반응을 조사하였다. 원적외선 가교 조건에서 카본블랙을 혼합한 EPDM 컴파운드는 입자크기가 증가함에 따라 열전도도가 증가하며 이에 따라 원적외선에 의한 가교도 역시 증가하였으나, 열풍에 의한 가교도의 변화에는 거의 영향을 주지 못하였다. 보강제 종류에 따른 원적외선 가교 특성 평가 결과, 열전도도가 높은 아세틸렌 블랙을 함유한 컴파운드의 가교도가 가장 높게 나타났으며, 열전도도가 유사한 카본블랙 및 침강실리카의 경우 상대적으로 원적외선 흡수 특성이 우수한 침강실리카 배합 컴파운드의 경우 원적외선에 의한 가교도가 높게 나타났다.

• 한국전기전자재료학회논문지
• /
• 제34권1호
• /
• pp.44-49
• /
• 2021

Recently, infrared (IR) and near-infrared (NIR) light-emitting diodes (LEDs) were widely used for home medical applications owing to its low output power and wide exposed area for curing. For deep penetration of the light under the skin, multiple LEDs with wavelengths of 700~10,000 nm were located on a flexible printed circuit board. When multiple wavelengths of LEDs were soldered on a circuit board, the lifetime of LED module highly depends on LEDs with a short lifetime. The mean time to failure (MTTF) was able to calculate with the experimental results under high temperature and the Arrhenius model. The results of this study could help companies to approve the warranty of LED modules and its product.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2008년도 추계학술대회 초록집
• /
• pp.114-114
• /
• 2008

자동차 보수도료 경화는 주로 열풍방식을 사용하고 있지만 적외선 가열방식을 사용하면 품질이 향상 되고 에너지 절약 등의 이점이 있다. 따라서 자동차 보수도료의 경화용으로 사용할 적외선 방사체를 개발하였다. 자동차 보수도료의 적외선 흡수 스펙트럼과 적외선 방사체 방사 스펙트럼이 일치해야 도료의 경화효율이 우수해짐을 알 수 있었고 열풍방식과 비교하여 경화된 도막의 품질 및 경화시간에 대한 실험데이터를 분석하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.73-76
• /
• 1999

Near infrared spectroscopy techniques were used to study the cure reactions of epoxy resin system based on diglycidyl ether of bisphenol A(DGEBA) resins cured with 4, 4' diaminodiphenyl sulfone (DDS) hardner. Stoichiometric DGEBA/DDS resin formulation was involved in this study. The infrared absorption spectra of the prepared formulation were obtained on an FTIR spectrometer operating in the region of 11000 to 4000$cm^{-l}$. The chemical group peaks of interest in a DFEBA/DDS spectrum were identified by a comparative study with individual spectra of DGEBA and DDS monomers. Where necessary, special model compounds were used to identify unknown bands, such as the primary amine band at 4535$cm^{-l}$. The absorption bands of interest were integrated to quantify the areas and then converted to molar concentrations. This series of quantitative analyses of the major chemical groups led us to understand not only the reaction mechanism but also the cure kinetics. In this paper, the reaction mechanisms observed in stoichiometric DGEBA/DDS resin formulation and the various properties of the resin system as a function of cure temperature are described.

• Restorative Dentistry and Endodontics
• /
• 제39권3호
• /
• pp.155-163
• /
• 2014

Objectives: Light-curing of resin-based materials (RBMs) increases the pulp chamber temperature, with detrimental effects on the vital pulp. This in vitro study compared the temperature rise under demineralized human tooth dentin during light-curing and the degrees of conversion (DCs) of three different RBMs using quartz tungsten halogen (QTH) and light-emitting diode (LED) units (LCUs). Materials and Methods: Demineralized and non-demineralized dentin disks were prepared from 120 extracted human mandibular molars. The temperature rise under the dentin disks (n = 12) during the light-curing of three RBMs, i.e. an Ormocer-based composite resin (Ceram. X, Dentsply DeTrey), a low-shrinkage silorane-based composite (Filtek P90, 3M ESPE), and a giomer (Beautifil II, Shofu GmbH), was measured with a K-type thermocouple wire. The DCs of the materials were investigated using Fourier transform infrared spectroscopy. Results: The temperature rise under the demineralized dentin disks was higher than that under the non-demineralized dentin disks during the polymerization of all restorative materials (p < 0.05). Filtek P90 induced higher temperature rise during polymerization than Ceram.X and Beautifil II under demineralized dentin (p < 0.05). The temperature rise under demineralized dentin during Filtek P90 polymerization exceeded the threshold value ($5.5^{\circ}C$), with no significant differences between the DCs of the test materials (p > 0.05). Conclusions: Although there were no significant differences in the DCs, the temperature rise under demineralized dentin disks for the silorane-based composite was higher than that for dimethacrylate-based restorative materials, particularly with QTH LCU.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.642-651
• /
• 1996

The purpose of this study was to evaluate the relationship between monomer compositions and the changes in the degree of conversion in the various layers of composites after additional heat curing. Four types of composites and 3 types of inlay ovens were used in this study. Composite was placed in a 4-mm thick teflon mold, and light cured from the top for 60 seconds. Ten samples were prepared for each composite ; 5 of these were additionally heat cured in an inlay oven as the manufacturer recommended. After light curing or light and heat curing, the samples were sectioned into four parts and assigned to groups A, B, C, or D according to their distance from the light source. These sections were then thinned to 50-$70{\mu}m$, and these wafers were analyzed with a Fourier Transform Infrared Spectrometer(FI-IR) to determine the degree of conversion. A standard baseline technique was used to calculate the degree of conversion. $^{13}C$ NMR spectra of bis-GMA, TEGDMA and bis-EMA, were acquired using a Varian Gemini spectrometer operated at 200 MHz. $CDCl_3$ solvent was used for qualitative analysis. The degree of conversion was affected by bis-GMA : TEGDMA ratio but it seemed to be also affected by other factors. When the composites were heat cured, significant increases in the degree of conversion were noted throughout the samples, but the amount of increase differed between materials. Thus, clinical performance of a heat-treated composite inlay may be different depending on materials.

• Geomechanics and Engineering
• /
• 제18권4호
• /
• pp.427-437
• /
• 2019

Waste materials are being produced in huge quantities globally, and the usual practice is to dump them into legal or illegal landfills. Recycled tiles (RT) are being used in soil stabilisation which is considered as sustainable solution to reduce the amount of waste and solve the geotechnical problems. Although the stabilisation of soil using RT improved the soil properties, it could not achieve the standard values required for construction. Thus, this study uses 20% RT together with low cement content (2%) to stabilise soft soil. Series of consolidated undrained triaxial compression tests were conducted on untreated and RT-cement treated samples. Each test was performed at 7, 14, and 28 days curing period and 50, 100, and 200 kPa confining pressures. The results revealed an improvement in the undrained shear strength parameters (cohesion and internal frication angle) of treated specimens compared to the untreated ones. The cohesion and friction angle of the treated samples were increased with the increase in curing time and confining pressure. The peak deviator stress of treated samples increases with the increment of either the effective confining pressures or the curing period. Microstructural and chemical tests were performed on both untreated and RT-cement treated samples, which included field emission scanning electron microscopic (FESEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and energy dispersive X-ray spectrometer (EDX). The results indicated the formation of cementation compounds such as calcium aluminium hydrate (C-A-H) within the treated samples. Consequently, the newly formed compounds were responsible for the improvement observed in the results of the triaxial tests. This research promotes the utilisation of RT to reduce the amount of cement used in soil stabilisation for cleaner planet and sustainable environment.

• 폴리머
• /
• 제36권3호
• /
• pp.268-274
• /
• 2012

실란 커플링제를 사용하여 알루미나 나노 입자의 표면을 처리하였다. 표면을 개질한 나노 입자를 in-mold decoration(IMD) 포일의 경질 코팅 층에 도입하여 표면 경도 및 내마모성을 중심으로 도막의 물성 변화를 평가하였다. 전자빔(electron beam, EB) 조사가 IMD 포일을 구성하는 color layer 및 anchor layer에 미치는 영향을 색도변화와 cross-cut tape 시험을 통하여 평가하였다. 또한 EB 조사 온도에 따른 경화 거동을 표면 물성 변화 평가 및 Fourier transform infrared(FTIR) spectroscopy 관찰을 통해 정량적으로 분석함으로써 EB 경화 공정의 실용화에 필요한 데이터베이스를 구축하였다.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.707-711
• /
• 2016

A small diameter of SiC fiber mat can produce much higher heat under microwave irradiation than the other types of SiC materials. Fabrication of high strength SiC fiber consists of iodine vapor curing on polycarbosilane precursor and heat treatment process. The curing stage of polycarbosilane fiber was maintained at $150-200^{\circ}C$ in a vacuum condition under the iodine vapor to fabricate a high thermal radiation SiC fiber. The structure and morphology of the fibers were characterized by Fourier transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TG) and scanning electron microscopy (SEM). In this study, the thermal properties of SiC fiber mats under microwave have been analyzed with an IR thermal camera and its image analyzer. The prepared SiC fiber mats radiated high temperature with extremely high heating rate up to $1100^{\circ}C$ in 30 seconds. The fabricated SiC fiber mats were not oxidized after the heat radiation process under the microwave irradiation.

• 대한치과보철학회지
• /
• 제47권4호
• /
• pp.416-423
• /
• 2009

연구목적: 이번 연구의 목적은 PLV 수복물의 접착 시 사용되는 광중합형 레진 시멘트의 중합도를 Fronrier transform infrared spectroscope로 측정하여 도재의 두께, 광원 및 광조사 시간에 따른 중합도의 차이를 비교하기 위함이다. 연구재료 및 방법: 대조군으로는 1.0 mm의 투명한 slide glass를 사용하였고, 도재 시편은 IPS Empress Esthetic shade ETC1을 선택하여 0.5, 1.0, 1.5 mm의 두께로 제작하였다. 레진 시멘트는 광중합형 레진 시멘트인 Rely $X^{TM}$ Veneer Shade A3를 사용하였다. 광원으로는 Quartz Tungsten Halogen (QTH), Light Emitting Diode (LED), Plasma arc curing (PAC) 광중합기를 사용하였다. 레진 시멘트의 중합도는 FT-IR과 OMNIC 프로그램을 이용하여 측정하였다. 통계분석은 one-way ANOVA와 Tukey HSD를 이용하였다 ($\alpha$=0.05). 결과: 대조군에서 QTH와 LED로 광중합을 시행하였을 때 PAC로 광조사를 시행한 경우보다 중합도가 높았다. QTH와 LED로 광조사를 시행한 경우, 대조군과 0.5 mm, 1.0 mm, 1.5 mm의 도재 두께에서 유의차를 보이지 않았다. 반면, PAC로 광조사를 시행한 결과, 도재의 두께가 1.5 mm인 실험군의 중합도가 대조군과 0.5 mm에서 보다 통계적으로 유의하게 낮은 결과를 보인다 (P<.05). 두께가 1.0 mm의 도재와 LED 광중합기로 광조사하여 중합도를 비교한 결과, 20초간 광조사를 시행하였을 때와 비교하여 80초와 160초간 광조사를 시행한 경우 통계적으로 유의하게 중합도의 평균값이 높았다 (P<.05). 결론: 이번 연구의 한계 내에서, 도재의 두께가 0.5-1.5 mm 이내의 PLV 접착 시, PAC 중합기의 사용은 고려되지 않으며, QTH나 LED로 40초 이상 중합한다면 광중합형 레진 시멘트를 사용할 수 있다. 또한, 광중합형 레진 시멘트를 LED로 중합시킬 경우, 광조사 시간의 증가가 중합도의 증가와 비례하지 않으며, 일정시간 이상의 광조사가 중합도에 큰 영향을 끼치지 않는다.