• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.53 no.4
• /
• pp.205-209
• /
• 2004

This research is investigated an energy saving system based on human detecting technique. It saves a lot of energy by automatic switching method of lighting, appliance, and so on. Existence of people on space is detected by infrared ray sensor. If there is not anybody during definite time, then main controller of system sends "power off" signal to lighting switches, and outlets. When people are detected again, turn on lighting switches and outlets. Result of this research is adaptable for classrooms and offices, and great effect of energy saving is expected.

• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.446-450
• /
• 2021

Non-dispersive infrared (NDIR) gas sensors typically use an optical filter that transmits a discriminating 4.26 ㎛ wavelength band to measure carbon dioxide (CO2), as CO2 absorbs 4.26 ㎛ infrared. The filter performance depends on the transmittance and full width at half maximum (FWHM). This paper presents the fabrication, sensitivity, and selectivity characteristics of a distributed Bragg reflector (DBR)-based Fabry-Perot filter with a simple structure for CO2 detection. Each Ge and SiO2 films were prepared using the RF magnetron sputtering technique. The transmittance characteristics were measured using Fourier-transform infrared spectroscopy (FT-IR). The fabricated filter had a peak transmittance of 59.1% at 4.26 ㎛ and a FWHM of 158 nm. In addition, sensitivity and selectivity experiments were conducted by mounting the sapphire substrate and the fabricated filter on an NDIR CO2 sensor measurement system. When measuring the sensitivity, the concentration of CO2 was observed in the range of 0-10000 ppm, and the selectivity was measured for environmental gases of 1000 ppm. The fabricated filter showed lower sensitivity to CO2 but showed higher selectivity with other gases.

• Korean Journal of Remote Sensing
• /
• v.27 no.3
• /
• pp.369-377
• /
• 2011

Since well-calibrated satellite data is critical for their applications, calibration and validation of COMS science data was one of the key activities during the IOT. COMS MI radiometric calibration process was divided into two phases according to the out-gassing of the sensor: calibrations of the visible (VI) and infrared (IR) channels. Different from the VIS calibration, the calibration steps for the IR channels followed additional processes to secure their radiometric performances. Primary calibration steps of the IR were scan mirror emissivity correction, midnight effect compensation, slope averaging and 1/f noise compensation after a nominal calibration. First, the scan mirror emissivity correction was conducted to compensate the variability of the scan mirror emissivity driven by the coating material on the scan mirror. Second, the midnight effect correction was performed to remove unreasonable high spikes of the slope values caused by the excessive radiative sources during the local midnight. After these steps, the residual (difference between the previous slope and the given slope) was filtered by a smoothing routine to eliminate the remnant random noises. The 1/f noise compensation was also carried out to filter out the lower frequency noises caused from the electronics in the Imager. With through calibration processes during the entire IOT period, the calibrated IR data showed excellent performances.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.448-453
• /
• 2002

Remote sensing technology is one of the most powerful tools for human to know the nature and their living environment. However, before microwave remote sensing was developed and applied, remote sensing application was limited strongly by weather and time. Microwave remote sensing technology solves the problem. It makes us to have the capability to acquire information at all time of the day and under all weather condition, and make remote sensing technology be used in more wider area. Microwave remote sensing system include mainly Synthetic Aperture Radar (SAR), Microwave Radiometer, Microwave Scatterometer, and Altimeter (ALT). As SAR can acquire image whose spatial resolution is similar with visible and infrared image, it is paying much attention to and playing a more and more important role in earth observation. In recent year, the development of new SAR technology (multi-band and multi-polarization technology, InSAR technology, D-InSAR technology, and so on) makes SAR remote sensing go to an new stage, and its application area become more and more widely. The first Synthetic Aperture Radar (SAR) in the world appeared in 1960. After that, SAR and its application all developed very fast. Some radar satellites launched and run (include Seasat-A in 1978, ERS-1 in 1991, JERS-1 in 1992, Radarsat in 1995, and so on) promote SAR research and application in world greatly. China began to develop its SAR sensor and research SAR application in 1970s. After more than 30 years' research, it get some important development in sensor development data processing method, and application. Some operational systems have been used and play an important role. This paper will introduce the development of SAR technology and its application in China.

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.86-90
• /
• 2001

A pyroelectric senior using P(VDF/TrFE) film for sensing materials has been fabricated and evaluated with other commercial pyroelectric sensors that use ceramic materials for sensing. The device was mounted in a TO-5 housing to detect infrared light of $5.5{\sim}14\;{\mu}m$ wavelength. The NEP (noise equivalent power) and specific detectivity $D^*$ of the device were $2.13{\times}10^{-8}\;W$ and $9.37{\times}10^6\;cm/w$ respectively under emission energy of $13\;{\mu}W/cm^2$ respectively. These result shows a better characteristics than other commercial pyroelectric sensors NEP $8.08{\times}10^{-7}\;W$ and $D^*$ $2.47{\times}10^5\;cm/w$.

• Korean Chemical Engineering Research
• /
• v.61 no.3
• /
• pp.463-471
• /
• 2023

Nitrogen-rich carbon dots (NDots) were synthesized by using uric acid as carbon and nitrogen sources. The as-synthesized NDots showed strong dual emissions at 420 nm and 510 nm with excitation at 350 nm and 460 nm, respectively. The physicochemical analyses such as X-ray photoelectron spectroscopy, Transmission electron microscopy and Fourier transform infrared spectroscopy were used to analyze the chemical, physical and morphological structures of NDots. The as-synthesized NDots exhibited wide linear range (0-100 µM) and very low detection limit (124 nM) in Ag⁺ ion sensing. In addition, Ag⁺ saturated NDots could be used as an EDTA sensor by the EDTA induced PL recovery.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.691-693
• /
• 2005

The prototype of the radiometric calibration algorithm, including the correction of scan mirror's angle, has been developed for the stationary meteorological sensor, firstly in Korea. We use this system on GOES-12 to evaluate two coefficients, slope and intercept. The evaluated coefficients show good agreement with the NESDIS's results for the five-case data. The calculated coefficients have been applied to the conversion from the measured counts to the radiance and the converting methods according to the scanning are investigated to enhance the radiometric accuracy.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.11a
• /
• pp.143-152
• /
• 2004

Researchers seeking geological and environmental information, depend on remote sensing and aerial photographic datum from various commercial satellites and aircraft. However, adverse weather conditions as well as equipment expense limit the ability to collect data anywhere and anytime. To allow for better flexibility in geological and environmental data collection, we have developed a compact, multi-spectral automatic Aerial Photographic system (PKNU2). This system's Multi-spectral camera can record visible (RGB) and infrared (NIR) band (3032＊2008 Pixels) images Visible and infrared band images were obtained from each camera respectively and produced color-infrared composite images to be analyzed for the purpose of the environmental monitoring. However this did not provide quality data. Furthermore, it has the disadvantage of having the stereoscopic overlap area being 60% unsatisfied due to the 12 seconds of storage time of each data The PKNU2 system in contrast, photographed photos of great capacity Thus, with such results, we have been proceeding to develop the advanced PKNU2 (PKNU3) system that consists of a color-infrared spectral camera that can photograph in the visible and near-infrared bands simultaneously using a single sensor, a thermal infrared camera, two 40G computers to store images, and an MPEG board that can compress and transfer data to the computer in real time as well as be able to be mounted onto a helicopter platform.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.10
• /
• pp.161-167
• /
• 2015

This paper presented an occupancy-based energy saving system for appliance energy saving in smart house. The developed system is composed of a sensing system and a home gateway system. The sensing system is set of wireless sensor nodes which have pyroelectric infrared (PIR) sensor to detect a motion of human and set of smart plugs which measure the current using CT (current transformer) sensor and send the current to home gateway wirelessly. We measured current consumption of appliances in real time using smart plugs, and checked the occupation of residents using occupancy sensors installed on the door and room. The proposed system saves electric energy to switch off the supply power of unnecessary usages in the unoccupied spaces. Experiments conducted have shown that electric energy usage of appliances can be saved about 34% checked by using occupation.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.1
• /
• pp.28-34
• /
• 2018

This paper is composed of a passenger management system using a temperature sensing module, a PIR sensor module for detecting movement inside a room, and a smart breath sensing module for determining a sleeping state. An embedded sensor module and a communication system integrated the sensing part and the algorithm driving part. As the aging society is accelerating and becoming more upgraded, the social cost of Silver Care increases, and in order to protect privacy, it is necessary to reduce costs by developing efficient smart silver care devices. The proposed non - image human body detection IOT sensor system is implemented by hardware and software and has superior performance compared with conventional image monitoring method.