• Korean Journal of Remote Sensing
• /
• v.36 no.2_1
• /
• pp.139-153
• /
• 2020

Using a computationalfluid dynamics(CFD) model, thisstudy evaluated the representativeness of an air quality monitoring system (AQMS) in an urban area and presented a methodology to determine the suitable AQMS locations for specific purposes. For this, we selected a 1.6 km × 1.6 km area around the Eunpyeong-gu AQMS (AQMS 111181) as a target area. We conducted simulationsfor two emission scenarios (scenario one: air pollutants transported from inflow boundaries, scenario two: air pollutants emitted from roads). Urban airflows were markedly influenced by mountainous terrain located in the northeast and southeast of the target area, and complicated airflow patterns occurred around the buildings. The distributions of air pollutants were dependent on the terrain (mountain) in scenario one, but the road location and building height in scenario 2. We evaluated whether the AQMS could represent the air quality in the target area based on the simulations for two scenarios. The concentrations simulated at the AQMS were similar in magnitude to the layer mean concentrations, which indicated good representativeness for the air quality in the target area. We also suggested which locations were suitable for different measurement purposes (hot spots, clean zones, average zones, shelter zones, equi-background zones).

• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.415-423
• /
• 2004

To investigate the long-term corrosion resistance of an uncoated weathering steel, an important outdoor constructional steel material, skyward surfaces of the weathering steel and a control steel initially exposed to rural and industrial atmospheres for 9 years were electrochemically tested in neutral artificial rain in terms of electrochemical potentials, impedances, and anodic potentiodynamic polarization curves. Their results were then discussed. A quite passive and stable rust layer to the artificial rain was well formed on the skyward surface of the weathering steel exposed to the industrial and rural atmospheres, and its corrosion rate in the artificial rain was measured to be about a low $3{{\mu}m}/y$. Continuous immersion of all the weathered surfaces in the artificial rain revealed the gradual degradation of the weathered corrosion layers on the steel, resulting in a cathodically controlled corrosion of the substrate steel by the electrochemical measurements. Alloy components of the weathering steel were found to retard the degradation of the weathered corrosion layers on the steel in the artificial rain. For better corrosion evaluation of the weathering steel, more electrochemical measurements of surfaces that have been exposed for more than 9 years to more closely simulated atmospheric waters are needed. These measurements are almost non-destructive and can provide online and in situ information on the corrosion rate, the development of corrosion and the conditions of rust layers on any interested surface and at any exposure time of the steel, so they can be effectively applicable to the corrosion evaluation of steel structures such as bridges, towers, and architectures by forming an electrochemical cell on an interested structural surface and by using a portable electrochemical instrument.

• Journal of Sericultural and Entomological Science
• /
• v.53 no.1
• /
• pp.6-11
• /
• 2015

Antheraea yamamai silkworm cocoon is considered as a natural biocompatible materials, but can not be used as medical resources due to its difficult processability. In this study, we examined the general characteristics including cocoon shell weight and structural and thermal properties of Antheraea yamamai silkworm cocoon. The cocoon shell weight and thickness of wild silkworm cocoon was 0.528 g and 0.424 mm, respectively. The cocoon has yellow-green color in outside cocoon but white in inner layer cocoon. Amino acid analysis showed that the main amino acid of Antheraea yamamai cocoon is alanine, glycine, serine, aspartic acid, tyrosine and arginine. X-ray diffractometry showed that strong diffraction peaks at $2{\theta}=16.8^{\circ}$, $20.4^{\circ}$, corresponded to ${\beta}$-sheet structure and sharp diffraction peaks at $2{\theta}=15.0^{\circ}$, $24.3^{\circ}$, $30.0^{\circ}$ due to the presence of calcium oxalate on cocoon surface. Antheraea yamamai cocoon was degraded at $370^{\circ}C$. These results might be used as basic information for development of non-textile materials using Anthereae yamamai silkworm cocoon.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.342-343
• /
• 2013

AlSb is a promising material for optical devices, particularly for high-frequency and nonlinear-optical applications. And AlSb offers significant potential for devices such as quantum-well lasers, laser diodes, and heterojunction bipolar transistors. In this work we study molecular beam epitaxy (MBE) growth of an unstrained AISb film on a GaAs substrate and identify the real-time monitoring capabilities of in situ spectroscopic ellipsometry (SE). The samples were fabricated on semi-insulating (0 0 1) GaAs substrates using MBE system. A rotating sample stage ensured uniform film growth. The substrate was first heated to $620^{\circ}C$ under As2 to remove surface oxides. A GaAs buffer layer approximately 200 nm- thick was then grown at $580^{\circ}C$. During the temperature changing process from $580^{\circ}C$ to $530^{\circ}C$, As2 flux is maintained with the shutter for Ga being closed and the reflection high-energy electron diffraction (RHEED) pattern remaining at ($2{\times}4$). Upon reaching the preset temperature of $530^{\circ}C$, As shutter was promptly closed with Sb shutter open, resulting in the change of RHEED pattern from ($2{\times}4$) to ($1{\times}3$). This was followed by the growth of AlSb while using a rotating-compensator SE with a charge-coupled-device (CCD) detector to obtain real-time SE spectra from 0.74 to 6.48 eV. Fig. 1 shows the real time measured SE spectra of AlSb on GaAs in growth process. In the Fig. 1 (a), a change of ellipsometric parameter ${\Delta}$ is observed. The ${\Delta}$ is the parameter which contains thickness information of the sample, and it changes in a periodic from 0 to 180o with growth. The significant change of ${\Delta}$ at~0.4 min means that the growth of AlSb on GaAs has been started. Fig. 1b shows the changes of dielectric function with time over the range 0.74~6.48 eV. These changes mean phase transition from pseudodielectric function of GaAs to AlSb at~0.44 min. Fig. 2 shows the observed RHEED patterns in the growth process. The observed RHEED pattern of GaAs is ($2{\times}4$), and the pattern changes into ($1{\times}3$) with starting the growth of AlSb. This means that the RHEED pattern is in agreement with the result of SE measurements. These data show the importance and sensitivity of SE for real-time monitoring for materials growth by MBE. We performed the real-time monitoring of AlSb growth by using SE measurements, and it is good agreement with the results of RHEED pattern. This fact proves the importance and the sensitivity of SE technique for the real-time monitoring of film growth by using ellipsometry. We believe that these results will be useful in a number of contexts including more accurate optical properties for high speed device engineering.

• The Journal of Engineering Geology
• /
• v.30 no.3
• /
• pp.289-302
• /
• 2020

To determine the shallow subsurface structure and sliding surface of land creeping in 2016 at Hadong-gun, Gyeongsangnam-do, geophysical surveys (electric resistivity, and refraction seismic methods, borehole televiewer) and slope stability analysis were conducted. The subsurface structure delineated with borehole lithologies and seismic velocity structures provided the information that the sediment layer on the top of the slope was rather as thick as 20 m and the underlying weathered rock (anorthosite) was thinner than 1 m. Based on the tension cracks observed during the geological mapping, televiewer scanning was performed at the borehole BH-2 and detected the intensive fracture zones at the ground-water level, associated with the slip weak zones mapped in dipole-dipole electrical resistivity section. Downslope sliding and slightly upward pushing at the apex of high resistive bedrock explains the curved slip plane of the land creeping. Such a convex structure might play a role of natural toe abutment for preventing the downward development of slip weak zones. In slope stability analysis, the safety factors of the slip weak zone are calculated with varying the groundwater levels for dry and rainy seasons and the downslope is founded to be unstable with safety factor of 0.89 due to fully saturated material in rainy season.

• Journal of Broadcast Engineering
• /
• v.19 no.4
• /
• pp.521-532
• /
• 2014

ATSC-M/H based hybrid 3DTV, which is one of the service compatible 3DTV system, has considerable quality gap between the left and right views. And CRA(Conditional Replenishment Algorithm) has been proposed to deal with the issue of resolution mismatch and improve the visual quality. In CRA, the disparity vectors of stereoscopic images are estimated. The disparity compensated left view and simply enlarged right view are compared and conditionally selected for generating the enhanced right view. In order to implement CRA, a fast algorithm is strongly required because the disparity vectors need to be obtained at every layer and the complexity of CRA is quite high. In this paper, we adopted SDSP(Small Diamond Search Pattern) instead of full search and predicted the initial position of search pattern by examining the spatio-temporal correlation of disparity vectors and also suggested the SKIP mode to limit the number of processing units. The computer simulation showed that the proposed fast algorithm could greatly reduce the processing time while minimizing the quality degradation of reconstructed right view.

• Journal of Korean Ophthalmic Optics Society
• /
• v.18 no.4
• /
• pp.541-548
• /
• 2013

Purpose: Marrow stromal cells (MSCs) have been known for their potential to trans-differentiate into neural and glial cells in vitro and in vivo. To investigate the influence of the developing host environment on the survival and morphological and molecular differentiation, murine MSCs transplanted into the eye of Brazilian opossum (Monodelphis domestica). Methods: Enhanced green fluorescent protein (GFP) - expressing MSCs were transplanted into developing Brazilian opossums. Animals were allowed to survive for up to 4 weeks after transplantation, at which time the eyes were prepared for immunohistochemical analysis. Results: Some transplanted MSCs survived and showed morphological differentiation into neural cells with some processes within the host vitreous chamber. Some transplanted cells expressed class III ${\beta}$-tubulin (TuJ1, a marker for neuronal cells) or glial fibrillary acid protein (GFAP, a marker for glial cells) or Nestin (a marker for neural stem cells). In addition, some transplanted cells were located in ganglion cell layer but did not show morphological and molecular differentiation. Conclusions: Our result show that the most effective stage of development for transplantation into the retina was postnatal day 16, which retinas developmentally corresponded to postnatal day 4-5 days mouse retina based on cell differentiation and lamination patterns. The present findings suggest that the age of the host appears to play a key role in determining cell fate in vivo.

• Journal of KIISE:Computer Systems and Theory
• /
• v.36 no.3
• /
• pp.171-180
• /
• 2009

Slowly, but surely, we are seeing the emergence of a variety of embedded systems that are employing Storage Class RAM (SCRAM) such as FeRAM, MRAM and PRAM, SCRAM not only has DRAM-characteristic, that is, random byte-unit access capability, but also Disk-characteristic, that is, non-volatility. In this paper, we propose a new software architecture that allows SCRAM to be used both for main memory and for secondary storage simultaneously- The proposed software architecture has two core modules, one is a SCRAM driver and the other is a SCRAM manager. The SCRAM driver takes care of SCRAM directly and exports low level interfaces required for upper layer software modules including traditional file systems, buddy systems and our SCRAM manager. The SCRAM manager treats file objects and memory objects as a single object and deals with them in a unified way so that they can be interchanged without copy overheads. Experiments conducted on real embedded board with FeRAM have shown that the SCRAM driver indeed supports both the traditional F AT file system and buddy system seamlessly. The results also have revealed that the SCRAM manager makes effective use of both characteristics of SCRAM and performs an order of magnitude better than the traditional file system and buddy system.

• Journal of KIISE:Software and Applications
• /
• v.37 no.4
• /
• pp.239-251
• /
• 2010

In modern distributed enterprise applications that have multilayered architecture, business entities are a kind of crosscutting concerns running through service components that implements business logic in each layer. When business entities are modified, service components related to them should also be modified so that they can deal with those business entities with new types, even though their functionality remains the same. Our previous paper proposed what we call the DTT (Data Type-Tolerant) component model to efficiently process the variability of business entities, which are data externalized from service components. While the DTT component model, by removing direct coupling between service components and business entities, exempts the need to rewrite service components when business entities are modified, it incurs the burden of implementing data type converters that mediate between them. To solve this problem, this paper proposes a method to use ontology as the metadata of both SCDTs (Self-Contained Data Types) in service components and business entities, and a method to generate data type converter code using the ontology. This ontology-based DTT component model greatly enhances the reusability of service components and the efficiency in processing data variability by allowing the computer to automatically generate data type converters without error.

• Journal of Advanced Navigation Technology
• /
• v.19 no.5
• /
• pp.423-432
• /
• 2015

This paper shows that design, manufacture and the performance of FC-NIC (fibre channel network interface card) for network unit configuration which is based on one of the 5 main configuration items of the common functional module for IMA (integrated modular Avionics) architecture. Especially, FC-NIC uses zynq SoC (system on chip) for host load reductions. The host merely transmit FC destination address, source memory location and size information to the FC-NIC. After then the FC-NIC read the host memory via DMA (direct memory access). FC upper layer protocol and sequence process at local processor and programmable logic of FC-NIC zynq SoC. It enables to free from host load for external communication. The performance of FC-NIC shows average 5.47 us low end-to-end latency at 2.125 Gbps line speed. It represent that FC-NIC is one of good candidate network for IMA.