• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.171-174
• /
• 2004

The surge characteristics of $Pr_6O_{11}$-based ZnO varistors consisting of $ZnO-Pr_6O_{11}-CoO-Cr_2O_3-Er_2O_3$ ceramics were investigated with sintering temperature in the range of $1335{\sim}1345^{\circ}C$. As the sintering temperature is raised, the average grain size was marked1y increased in the range of $9.67{\sim}14.07\;{\mu}m$ and the ceramic density was increased in the range of $5.46{\sim}5.59\;g/cm^3$. While, the nonlinear exponent was decreased in the range of 64.9~44.1 and the clamping voltage ratio was improved in the range of 1.99~2.08. The best varistor properties was obtained from the varistors sintered at $1335^{\circ}C$, exhibiting a maximum (64.9) in the nonlinear exponent and a minimum (1.99) in the clamping voltage ratio.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.3
• /
• pp.311-323
• /
• 2019

The number of newly constructed traditional Korean houses, i.e., Hanoks, and light-frame buildings is increasing. However, related research is limited owing to the lack of awareness regarding safety evaluations. Therefore, this study conducted an outdoor exposure test to accurately evaluate wooden constructions. Spruce, pine, and fir (SPF) material was monitored for a year, wherein the SPF material was artificially dried under 18% moisture content, and its physical properties and color differences were measured once a month. Large differences were observed in the material's weight and moisture content, which are indexes sensitive to daily range and rainfall; however, no significant difference was found for other basic properties in the pre and post test results. Herein, $L^*$, $a^*$, and $b^*$ values represent color differences; these values exhibited a general decrease after the test. Such differences were attributed to the loss of lignin in the wood. The color difference value was high between the months of May and July, when the daily range and rainfall significantly fluctuated. Multiple regression analysis was performed on the $a^*$ value (redness indicator), daily range, rainfall, and ultraviolet index. The results indicated that the daily range influenced redness the most. According to the estimated regression equation, the daily range and redness are positively correlated. Based on the results, the types and influence of independent variables on color difference are expected to change as the wood's duration of outdoor exposure and the amount of data obtained both increase.

• Geomechanics and Engineering
• /
• v.24 no.4
• /
• pp.359-370
• /
• 2021

Joint roughness is combination of primary and secondary roughness. Ordinarily primary roughness is a geostatistical part of a joint surface that has a periodic nature but secondary roughness or unevenness is a statistical part of that which have a random nature. Using roughness generating algorithms is a useful method for evaluation of joint roughness. In this paper after determining geostatistical parameters of the joint profile, were presented two roughness generating algorithms using Mount-Carlo method for evaluation of primary (GJRGAP) and secondary (GJRGAS) roughness. These based on geostatistical parameters (range and sill) and statistical parameters (standard deviation of asperities height, SDH, and standard deviation of asperities angle, SDA) for generation two-dimensional joint roughness profiles. In this study different geostatistical regions were defined depending on the range and SDH. As SDH increases, the height of the generated asperities increases and asperities become sharper and at a specific range (a specific curve) relation between SDH and SDA is linear. As the range in GJRGAP becomes larger (the base of the asperities) the shape of asperities becomes flatter. The results illustrate that joint profiles have larger SDA with increase of SDH and decrease of range. Consequencely increase of SDA leads to joint roughness parameters such Z2, Z3 and RP increases. The results showed that secondary roughness or unevenness has a great influence on roughness values. In general, it can be concluded that the shape and size of asperities are appropriate parameters to approach the field scale from the laboratory scale.

• Journal of the Korean Institute of Gas
• /
• v.26 no.4
• /
• pp.27-35
• /
• 2022

When LPG leaks from the storage tank, the gas try to sink to the ground because LPG is heavier than air. The gas easily creates vapor clouds causing aggressive accidents in no airflow. Therefore, It is important to prevent in advance by analyzing the damaged range caused from LPG leakage and vapor clouds. So, this study analyzed the range of damaged by LPG leakage and vapor clouds with consideration of the cold air flow which is generated by the topographical characteristics and the land use status at night time in the Jeju Hagari. As a result of the cold air flow using KLAM_21, about 2 m/s of cold air was introduced in from the southeast due to the influence of the terrain. The range of damaged by LPG leakage and vapor cloud was analyzed using ALOHA. When the leak hole size is 10 cm at the wind speed of 2 m/s, the range corresponding to LEL 60 % (12,600 ppm) was 61 m which range is expected to influence in nearby residential areas. These results of this study can be used as basic data to prepare preventive measures of accidents caused by vapor cloud. Forward, it is necessary to apply CFD modeling such as FLACS to check the vapor cloud formation due to LPG leakage in a relatively narrow area and to check the cause analysis.

• Journal of the Korean Ceramic Society
• /
• v.13 no.3
• /
• pp.3-12
• /
• 1976

The corelation between surface tensions and surface appearances of SK O5a opaque glazes for earthen wares were investigated. The surface tension values were theoretically calculated by using Dietzel's factors of constituent oxides of glaze. The surface appearances of glazes, especially the pinhole phenomena were strongly effected by the surface tension values showing the following general tendencies: (1) In the range of 305±3 dynes/cm of surface tensions, glazes showed almost no pjnholes. (2) In the range of surface tensions less than 300 dynes/cm, the large numbers of small pinholes or eggshell textures were observed. (3) In the range of surface tensions higher than 310 dynes/cm, large and deep pinholes were observed. (4) The contact angles of glazes on the wall tile body substrate are in the good proportional agreement with the surface tension values calculated by Dietzel's factors.

• Journal of the Korean Ceramic Society
• /
• v.19 no.3
• /
• pp.205-214
• /
• 1982

The method of lowering the sintering temperature and enlarging the range of sintering temperature in the manufacture of forsterite porcelain as a high frequency insulator was investigated. The four kinds of forsterite chamotte were calcinated at $1400^{\circ}C$. The forsterite bodies produced by adding $BaCO_3$ as a flux and 5% Kaolin as a bonding agent were heated in the range of sintering temperature. Sintering temperature tended to increase almost straightly as MgO exceded without $BaCO_3$. The range of sintering tem was at least $140^{\circ}C$. Specimens of MF-2-0, MF-2-A had superior mechanical strength and dielectric properties. The growing of the forsterite crystal was restricted and thus their grain size became fine and also the amount of crystal formation tended to decrease rapidly as $BaCO_3$ increased excessively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.5
• /
• pp.7-11
• /
• 2007

Kraft pulping of Trema orientalis (Nalita) was studied in order to find kinetic data for delignification. Pulping runs were carried out in the temperature range of $160-180\;^{\circ}C$ under constant and well-defined conditions. The delignification was found to be first order with respect to residual lignin and was chemically controlled. The rate of delignification reaction was increased 1.11-1.23 for $10\;^{\circ}C$ temperature increase in the range of $160-180\;^{\circ}C$ range. A mean value of 93% of lignin was removed at the transition between bulk and residual delignification. The influence of cooking temperature on the rate constant was expressed by an Arrhenius-type equation. The obtained activation energy of the delignification reaction was 6,164 cal/mol. The transition point between bulk and residual phase was shifted to lower lignin and carbohydrate yield with the increase of temperature.

• Atmosphere
• /
• v.21 no.1
• /
• pp.45-55
• /
• 2011

A definition on the tropical cyclone (TC) that influenced the Korean Peninsula (KP), the KP-influence TC, is widely used in the TC communities, but its criterion is not clear mainly due to the ambiguity and subjectiveness of the term such as 'influence', which led to the inconsistent TC statistical analysis. This study suggests a definition and criterion on the TC approaching to the KP (KP-approach TC) additionally, which is more obvious and objective than the KP-influence TC. In this study, the criterion on the KP-approach TC is determined when the TC's center from the RSMC best track data encounters the box areas of $28^{\circ}N{\sim}40^{\circ}N$ and $120^{\circ}E{\sim}138^{\circ}E$. The range is chosen by finding a minimum area that includes all official KP-influence TCs except three TCs that affected the KP as a tropical depression (TD). Statistical analysis reveals that, among total 1,537 TCs that occur in the western North Pacific during 1951-2008, the KP-approach TC was 472, the KP-influence TC was 187, and the KP-landfall TC was 87. August was the month that the largest TCs approach and influence to the KP. Finally, this paper suggests to determine the KP-influence TC by the strong wind and heavy rain advisories in the KP based on the observation after the storm's passage.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2817-2822
• /
• 2007

The purpose of this paper is to study the influence of operating condition and ejector geometries on the hydrodynamics and on the mass transfer characteristic of ejector. The CFD results were validated with available experimental data. Flow field analyses and predictions of ejector performance were also carried out. Variation on the operating conditions was made by varying the gas-liquid flow rate ratio in the range of 0.2 to 1.2. The ejector configuration was also varied on the length to diameter ratio of mixing tube ($L_M/D_M$) in the range of 4 to 10. CFD studies show that at $L_M/D_M$ 5.5, the volumetric mass transfer coefficient increases with respect to gas flow rates. Meanwhile, at $L_M/D_M$ 4, the plot of volumetric mass transfer coefficient to gas-liquid flow rates ratio reach maximum at gas-liquid flow rates ratio of 0.6. This study also shows that volumetric mass transfer coefficient decrease with respect to the increase of mixing tube length.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.2
• /
• pp.185-206
• /
• 2015

This paper presents statistical models developed to study the influence of key mix design parameters on the properties of lightweight self-consolidating concrete (LWSCC) with expanded shale (ESH) aggregates. Twenty LWSCC mixtures are designed and tested, where responses (properties) are evaluated to analyze influence of mix design parameters and develop the models. Such responses included slump flow diameter, V-funnel flow time, J-ring flow diameter, J-ring height difference, L-box ratio, filling capacity, sieve segregation, unit weight and compressive strength. The developed models are valid for mixes with 0.30-0.40 water-to-binder ratio, high range water reducing admixture of 0.3-1.2 % (by total content of binder) and total binder content of $410-550kg/m^3$. The models are able to identify the influential mix design parameters and their interactions which can be useful to reduce the test protocol needed for proportioning of LWSCCs. Three industrial class ESH-LWSCC mixtures are developed using statistical models and their performance is validated through test results with good agreement. The developed ESH-LWSCC mixtures are able to satisfy the European EFNARC criteria for self-consolidating concrete.