• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.464-470
• /
• 2010

A new method for the poling of piezoelectric ceramics with an air insulation medium in stead of silicon oil is described. A similar variation of electromechanical coupling coefficient $K_t$, for an air medium is observed in comparison to that of the material poled by the conventional poling method using a silicon oil medium. Different poling parameters such as dielectric constant $\varepsilon^T$ and frequency deviation ${\Delta}f$ are studied as well as the influence on the aging effect. The required poling factors to achieve the optimal piezoelectric characteristics are electric field, 2 kV/mm, temperature $100^{\circ}C$, and poling time 30 Min. From this result electric field 3 kV/mm atmosphere airs there being will be able to use with the polarization insulation medium about the piezoelectric material, confirmed.

• 유체기계공업학회:학술대회논문집
• /
• 2001.11a
• /
• pp.143-148
• /
• 2001

In this study, to investigate the effect of the generalized performance curve on the performance prediction and to find the optimal ones, a systematic study is performed. For this purpose, we compared the influence of the stage performance curves with experimental data in multi-stage axial compressors. As a result, it is discovered that the optimal generalized performance curves vary according to the number of the stages in compressors. And we found that for a low-stage compressors, Muir's pressure coefficient curve gives the best prediction results at design rotational frequency regardless of the efficiency curve. On the other hand, for high-stage compressors, Stone's pressure coefficient curve gives the optimistic results about the performance prediction at design rotational frequency.

• Journal of Mechanical Science and Technology
• /
• v.15 no.9
• /
• pp.1292-1301
• /
• 2001

The mean-line method using empirical models is the most practical method of predicting off-design performance. To gain insight into the empirical models, the influence of empirical models on the performance prediction results is investigated. We found that, in the two-zone model, the secondary flow mass fraction has a considerable effect at high mass flow-rates on the performance prediction curves. In the TEIS model, the first element changes the slope of the performance curves as well as the stable operating range. The second element makes the performance curves move up and down as it increases or decreases. It is also discovered that the slip factor affects pressure ratio, but it has little effect on efficiency. Finally, this study reveals that the skin friction coefficient has significant effect on both the pressure ratio curve and the efficiency curve. These results show the limitations of the present empirical models, and more resonable empirical models are reeded.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.176-184
• /
• 2001

The VDC(Vehicle Dynamics Control) is a control system whose target is to improve vehicle stability under critical motion. The system has a good potential of becoming a standard active safety unit in passenger vehicles since it can be implemented on top of the ABS/TCS system with little extra cost. This, however, is possible only when the signals that the VDC system demands can be obtained with sufficient accuracy. In this research, estimators for the road friction coefficient and body sideslip angle have been designed. The two variables have great influence upon performance of the VDC system but not directly measurable. For the estimator design, the Newton method and the nonlinear observer theory have been exploited. The performance of the estimator have been verified via simulations on critical driving conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.9
• /
• pp.1248-1255
• /
• 2003

Pressure coefficient in a rotating discharge hole was measured to gain insight into the influence of rotation on the discharge characteristics of rotating discharge holes. Pressures inside the hole were measured by a telemetry system that had been developed by the authors. The telemetry system is characterized by the diversity of applicable sensor type. In the present study, the telemetry system was modified to measure static pressure using piezoresistive pressure sensors. The pressure sensor is affected by centrifugal force and change of orientation relative to the gravity. The orientation of sensor installation for minimum rotating effect and zero gravity effect was found out from the test. Pressure coefficients in a rotating discharge hole were measured in longitudinal direction as well as circumferential direction at various rotating speeds and three different pressure ratios. From the results, the behaviors of pressure coefficient that cannot be observed by a non-rotating setup were presented. It was also shown that the discharge characteristics of rotating discharge hole is much more influenced by the Rotation number irrespective of pressure ratio.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.147-157
• /
• 2005

In this study, consolidation analysis methods reflecting various ground condition and changing coefficient of consolidation with consolidation process are presented. Research activities include development of numerical program consists of two parts considering vertical drainage only and both drainage condition with vertical and radial direction. Also, interface equation of adjacent two layers and function for changing coefficient of consolidation are added to developed program. This paper presents the results from a detailed consolidation analyses, which explores consolidation process with time in varying layered system and changing coefficient of consolidation

• Journal of Environmental Health Sciences
• /
• v.35 no.2
• /
• pp.130-142
• /
• 2009

This study compared FTIR with XRD method for the analysis of quartz by % recovery, coefficient of variation (CV) and influence of the interference. the results were as the following. 1. In FTIR method, the coefficient of determination ($r^2$) was 0.9998 in a calibration curve of $695\;cm^{-1}$, and the limit of detection was $4.9{\mu}g/sample$. 2. The highest recovery was $799\;cm^{-1}$ (98.2%). 3. The CVpooled of the FTIR method was approximately 10% in three wave numbers. 4. The analysis of qualitative and quantitative for quartz is difficult with mixed cristobalite and iron oxide. 5. In XRD method with rotating sample holder and LynxEye detector, the coefficient of determination was 0.9996 in a calibration curve, and the limit of detection was $5.9{\mu}g/sample$. 6. The recovery and CV pooled were 104.3%, and 11 %, respectively. 7. In muffle furnace ashing, the quartz weight decreased to 34% when the maximum weight of the iron oxide was more than eight times. In conclusion, the accuracy (% recovery) and precision (CV) of FTIR and XRD method for analyzing $\alpha$-quartz were similar. FTIR method was a disadvantage for sample matrix because it indicates possibility of interference. However, XRD method distinguished specific crystalline forms of silica, and the majority of silicate minerals. In addition, XRD method recommend filter dissolution to pretreatment method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.8
• /
• pp.744-749
• /
• 2011

In this study, determination method of initial optimal nozzle expansion in pintle rocket was investigated. The initial optimal initial nozzle expansion was decided by maximizing the mass-averaged thrust coefficient that is calculated from thrust coefficient of minimum and maximum chamber pressure. The determination of initial optimal initial nozzle expansion was equivalent to that of the minimum propellant mass which was required for obtaining the desired mission performance. The highest pressure, thrust turndown ratio and total impulse ratio effected on the initial optimal nozzle expansion. Among them, total impulse ratio had great influence on the initial optimal nozzle expansion.

• Geomechanics and Engineering
• /
• v.29 no.6
• /
• pp.599-614
• /
• 2022

In this study, the reliability analysis of internal and external stabilities of Reinforced Soil Walls (RSWs) under static and seismic loads are investigated so that it can help the geotechnical engineers to perform the design more realistically. The effect of various variables such as angle of internal soil friction, soil specific gravity, tensile strength of the reinforcements, base friction, surcharge load and finally horizontal earthquake acceleration are examined assuming the variables uncertainties. Also, the correlation coefficient impact between variables, sensitivity analysis, mean change, coefficient of variation and type of probability distribution function were evaluated. In this research, external stability (sliding, overturning and bearing capacity) and internal stability (tensile rupture and pull out) in both static and seismic conditions were investigated. Results of this study indicated sliding as the predominant failure mode in the external stability and reinforcing rupture in the internal stability. First-Order Reliability Method (FORM) are applied to estimate the reliability index (or failure probability) and results are validated using the Monte Carlo Simulation (MCS) method. The results showed among all variables, the internal friction angle and horizontal earthquake acceleration have dominant impact on the both reinforced soil wall internal and external stabilities limit states. Also, the type of probability distribution function affects the reliability index significantly and coefficient of variation of internal friction angle has the greatest influence in the static and seismic limits states compared to the other variables.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.18 no.1
• /
• pp.1-10
• /
• 2016

The purpose of this study was to examine the influence of elderly women's makeup behavior, psychological traits and demographic variables on their preference for makeup images in daily life(hereinafter called general makeup image) and for the makeup images of their own future funeral portraits. As for the method of research, a research study was implemented by using the questionnaire method. Seven factors were selected for makeup behavior: fashionability, conformity, subjectivity, instrumentality, interpersonal orientation and conspicuousness. The selected psychological traits were personality, death attitude and depression. Preference for general makeup image and for the makeup image of funeral portrait were investigated in terms of four: agreeableness, refinement, individuality and dignity. The subjects in this study were 651 female elderly residents in and around Seoul who were in their 60s to 80s. Concerning data analysis, factor analysis, Cronbach alpha coefficient, Pearson productmoment correlation coefficient, t-test, one-way ANOVA, Duncan's multiple range test and multiple regression analysis were utilized. Concerning the influence of the elderly women's makeup behavior, personality, death attitude, depression and demographic variables on preference for the makeup image of funeral portrait, their preference for an agreeable makeup image was analyzed. Thus, makeup behavior, personality, death attitude and depression were identified as the variables to exert a significant influence on preference for the makeup images of funeral portrait. The findings of the study are expected to help make makeup for funeral portrait entrenched as a part of the beauty industry and to make a contribution to the development of the beauty industry.