• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1097-1102
• /
• 2022

With the continuous development of the current industry, the current global environment is in a very serious situation, with resource supply and demand dependent on imports and huge costs for waste disposal due to the depletion of resources and mass generation of industrial waste. Its limitations have already been revealed in many fields, and the importance of re-manufacturing is drawing attention as a countermeasure to these problems. Re-manufacturing aims to recover products that are in the aging and disposal stages, recover to performance close to new products, and re-commercialize them. Among them, most of the machine tools are made of materials such as steel and cast iron with large structures, and raw materials are widely used when producing new products. In addition, since a lot of carbon is generated due to production, it is an object that can obtain a great re-manufacturing effect. Planner millers belonging to large machine tools are one of the machine tool equipment that can greatly reduce resources and energy through re-manufacturing because the structure is very large and the casting is several to tens of tons. Through this machine tool, performance tests and results are derived on the development of re-manufacturing source technology and domestic servo motor and CNC control device.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1111-1117
• /
• 2022

Recently, interest in the circular economy has emerged in the industry. As a result, interest in Re-manufacturing, which makes old equipment similar to new products, is growing. In the machine tool industry with many aging equipment, the Re-manufacturing industry is essential, and among them, research on the performance improvement of gear type oil pumps was conducted. The purpose was to achieve the target performance of flow rate and volume efficiency by changing the shape of the gear pump housing clearance and inlet/outlet, and Computational Fluid Analysis and Central Composite Design were conducted using ANSYS CFX 2022 R2 and MINITAB®. The level of each determined factor was determined. 20 design points were derived, and the Flow Rate at each design point was calculated, and the Theoretical Flow Rate was calculated to obtain Volumetric Efficiency. The optimal design point was obtained when the Flow Rate was 140 lpm and the Volumetric Efficiency was maximum, the optimal design point was obtained when both were maximum, and the Surface Plot for each factor was obtained to identify the tendency.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.5
• /
• pp.98-104
• /
• 2022

When processing parts, the cutting oil can improve the cooling performance of the workpiece and tool to increase the precision of the workpiece or extend the life of the tool and facilitate chip extraction. Since such cutting oil has a harmful effect on the environment and the human body due to additives such as sulfur, research on a minimum lubrication supply method using an eco-friendly oil is recently underway. The minimum lubrication supply method minimizes the amount of cutting oil used during processing and processes it, which can reduce the amount of cutting oil used, but has a problem in that cooling performance efficiency is poor. Therefore, this study conducted a study on mist cooling of lubricants to reduce the amount of cutting oil used and maximize the cooling effect of processing heat generated during tapping processing. Spray pressure, processing speed, direction, and lubricant spray amount, which are considered to have an effect on cooling performance, were set as process conditions, and the effect on temperature was analyzed by performing an experiment using the box benquin method among experiments were analyzed. Through the experimental analysis results, the optimal conditions for mist and processing that maximize the cooling effect were derived, and the validity of the results derived through additional experiments was verified. In the case of processing by applying the mist lubrication method verified through this study, it is considered that high-precision processing is possible by improving the cooling effect.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.2
• /
• pp.54-63
• /
• 2022

Among the various industrial robots, palletizing robots have received particular attention because of their higher productivity in accordance with technological progress. When designing a palletizing robot, the main components, such as the servo motors and reducers, should be properly selected to ensure its performance. In this study, a practical method for selecting the motors and reducers of a robot was proposed by performing the dynamic analysis of rigid-flexible multibody systems using ANSYS and ADAMS. In the first step, the links and frames were selected based on the structural analysis results obtained from ANSYS. Subsequently, a modal neutral file (MNF) with information on the flexible body was generated from the links and frames using modal analysis through ANSYS and APDL commands. Through a dynamic analysis of the flexible bodies, the specifications of the major components were finally determined by considering the required torque and power. To verify the effectiveness of the proposed method, the analysis results were compared with those of a rigid-body model. The comparison showed that rigid-flexible multibody dynamic analysis is much more useful than rigid body analysis, particularly for movements heavily influenced by gravity.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.4
• /
• pp.337-345
• /
• 2022

The foundation of high-rise concrete building in coastal areas generally must be installed in an integrated manner, not separately, in order to prevent defects caused by stress on the upper and lower parts of the mounting surface and to manage the process smoothly. However, when performing integrated punching, there is a concern that temperature stress cracks may occur due to hydration heat. Due to the large member size, it is difficult to make a sufficient commitment, so it is necessary to mix concrete with high self-charging properties to ensure workability. In this research, the amount of high-performance spray and admixture used was adjusted as experimental variables to satisfy this required performance. Through the analysis of the results for each blending variable, it was found that the unit quantity was 155kg/m³ and the cement ratio in the binder was 18%, and the target values of the pre-concrete properties and compressive strength were satisfied. A four-component binder(18% cement, 50% slag fine powder, 27% fly ash, 5% silica fume) was used.

• Fashion & Textile Research Journal
• /
• v.25 no.2
• /
• pp.221-229
• /
• 2023

This study aims to develop knee protectors that provide high safety and fitness, while incorporating a motion-adaptable 3D-printed pad. These protectors were evaluated by individuals who experience knee discomfort or pain. The results are as follows. First, the 3Dprinted pad design of a hexagonal mesh structure, which is modeled for excellent appearance and knee movement. Each unit of the mesh has a outer layer of 2mm thick, a spacer layer of 1 mm in diameter, and is connected by a 1.5 mm bridge. The bridge was extended up to 1.2 cm. Second, the knee brace was designed in three types - cylinder, strap, and combination by Universal design. Impact protection measurements of the three knee protectors demonstrated roughly 80% reduction in impact. Third, based on usability evaluation, cylinder type protectors have the highest ratings in most areas, primarily because of their ease of use. The strap type protector received positive reviews in terms of appearance and care, and the combination type provided stable knee protection. This study demonstrated the potential industrial application of 3D printing technology by designing and evaluating protective products for the human body. The results of this study are expected to aid knee protector manufacturers in developing practical products and promoting the development of protective equipment for other body parts or purposes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.5
• /
• pp.675-687
• /
• 2023

The border area between the South and North Korea is considered a stage for promoting Green Détent through the transformation of the Demilitarized Zone into the Green Peace Zone. This paper proposes 'Prosuming-index' composed of items to evaluate the multi-layered nature of industrial and infrastructure projects in the ecological and environmental fields planned in the border area. Based on the prosuming-index, we derived the following four types of potential for Green Detent practice in the border area-first, the Incheon and Ganghwa regions as 'a logistics/human network and agricultural/fishery production area', second, the northern Gyeonggi region as a 'cooperative network area based on the smart technology industries', third, the western Gangwon and the parts of nothern Gyeonggi region, as 'a multiple prosumer's area based on carbon neutral technologies', lastly, the eastern Gangwon region, as 'a transition area from idle or aged infrastructure to green infrastructure through the renewable energy industries'.

• International Journal of Computer Science & Network Security
• /
• v.23 no.3
• /
• pp.193-202
• /
• 2023

Numerous articles under the study and the examination of heavy metals in human teeth have been published in recent years. The heavy metal poisoning is a widespread issue emerged in toxicology area these days. It has been discovered that long-term exposure to heavy metals typically present in traces, in our everyday meals, drinking water, and in the environment as pollution causes heavy metal poisoning in human beings. Industrial effluents, Coal and Oil, as well as a variety of consumer items, such as cosmetics, can all cause this type of exposure. Teeth, which are often thought of as exoskeleton parts, store heavy metals with a high affinity and represent long-term exposure information. In this study, we have chosen and examined the sections of dentine instead, then examined the entire tooth. We have combined the work done on the examination of heavy metals in human teeth using several instrumental approaches e.g. "Optical Spectroscopic Techniques" to detect elemental profile of human teeth in the current study.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.158-163
• /
• 2023

Recently, the global demands for high voltage power semiconductors are increasing across various industrial fields. The use of electric cars with high safety and convenience is becoming practical, and IGBT modules of 3.3 kV and 1.2 kA or higher are used for electric locomotives. Delicate design and advanced process technology are required, and research on the optimization of high-voltage IGBT parts is urgently needed in the industry. In this study, we attempted to design a simulation process through TCAD (technology computer-aid design) software to optimize the process conditions of the fielding process among the core unit processes for an especial high yield voltage. As well, the prior circuit technology design and a ring pattern with a large number of ring formation structures outside the wafer similar to the chip structure of other companies were constructed for 3.3 kV NPT-IGBT through a unit process demonstration experiment. The ring pattern was designed with 21 rings and the width of the ring was 6.6 ㎛. By changing the spacing between patterns from 17.4 ㎛ to 35.4 ㎛, it was possible to optimize the spacing from 19.2 ㎛ to 18.4 ㎛.

• Journal of the Korean Institute of Rural Architecture
• /
• v.24 no.4
• /
• pp.133-139
• /
• 2022

This study deals with the formation of Jongyeonbangjeok's Gwangju Factory in the 1930's to 80's, and the findings are shown below: In the period of formation, the factory was rectangular-shaped from north to south, and the structure was located at the center of the site, and in the east of it, there was a dormitory connected from south to north. The building was arranged with an open area on the south. In the east of the site where company houses were located, same-sized structures were arranged along the axis.In the period of change, the factory was restored about the damage from the Korean War, and it went through the process of division into two companies. As a result, the factory in the center of the site was divided into left and right ones, and the dormitory and the group of company houses were, too, divided into two, so division was made largely into southern and northern parts. In the period of stabilization, along with factory extension in each of the companies, welfare for factory workers was expanded by building more houses or opening sport facilities. After the 1980's, too, the existing factories were either extended or remodeled according to the induction of equipment, and some showed changes in their functions due to a fire or such.