• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.199-204
• /
• 2007

Hot embossing, one of Nanoimprint Lithography(NIL) techniques, has been getting attention as an alternative candidate of next generation patterning technologies by the advantages of simplicity and low cost compared to conventional photolithographies. A typical hot embossing usually, however, takes more than ten minutes for one cycle of the process because of a long thermal cycling. Over the last few years a number of studies have been made to reduce the cycle time for hot embossing or similar patterning processes. The target of this research is to develop an induction heating apparatus for heating a metallic micro patterning mold at very high speed with the large-area uniformity of temperature distribution. It was found that a 0.5 mm-thick nickel mold can be heated from $25^{\circ}C$ to $150^{\circ}C$ within 1.5 seconds with the temperature variation of ${\pm}5^{\circ}C$ in 4-inch diameter area, using the induction heating apparatus.

• 조명전기설비학회논문지
• /
• 제22권3호
• /
• pp.40-51
• /
• 2008

This research presents a new active auxiliary resonant snubber with for induction heating PWM high frequency inverter solving the problem of induction heating PWM high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the active auxiliary resonant snubber with for induction heating PWM high frequency inverter. The inverter circuit which is attempted by the on-off operation of a switch has the effect of reducing the power loss due to soft switching and high frequency switching. This confirms that power regulation is possible on a continuous basis from 0.25[kW] to 2.84[kW] where the duty factor(D) changes from 0.08 to 0.3 under zero current switching which operates by an asymmetrical pulse width modulating control. The power conversion efficiency is 95[%]. Due to these results, the active auxiliary resonant snubber for an induction heating PWM high frequency inverter is considered effective as a source of induction heating.

• 소성∙가공
• /
• 제16권4호
• /
• pp.282-287
• /
• 2007

Hot embossing, one of Nanoimprint Lithography(NIL) techniques, has been getting attention as an alternative candidate of next generation patterning technologies by the advantages of simplicity and low cost compared to conventional photolithographies. A typical hot embossing usually, however, takes more than ten minutes for one cycle of the process because of a long thermal cycling. Over the last few years a number of studies have been made to reduce the cycle time for hot embossing or similar patterning processes. The target of this research is to develop an induction heating apparatus for heating a metallic micro patterning mold at very high speed with the large-area uniformity of temperature distribution. It was found that a 0.5 mm-thick nickel mold can be heated from $25^{\circ}C\;to\;150^{\circ}C$ within 1.5 seconds with the temperature variation of ${\pm}5^{\circ}C$ in 4-inch diameter area, using the induction heating apparatus.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.260-262
• /
• 2002

The scope of applications industrial or household manufactures, is on the increase. In this study, it applies a principle of induction heating to food dryness for preservation of food. And it applies indirect heating process using overheating steam, which analyzes thermal characteristic of heating apparatus depending on its construction. It was verified that application of proposed process was appropriate by drying test of food.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.670-674
• /
• 1997

Semi-solid forging is a compound forging technology to deventional forging process. Among several steps of semi-solid forging process, the heating step of a billet prior to semi-solid forging step is necessarily required to obtain globular microstructure. For the forming operation to work properly, it is also important to heat the billet uniformly for the uniformity of solid-liquid distribution. To satisfy these requirements, induction heating has been generally used for a long time. This paper presents the method to find heating condition and the temperature distribution inside of a billet with a induction heating apparatus by comparing the computer simulation with experiment for aluminum alloys Al2024 and A356.

• 한국정밀공학회지
• /
• 제14권8호
• /
• pp.15-20
• /
• 1997

Semi-solid forging is a compound forging technology to develop conventional forging process. Among several steps of semi-solid forging process, the heating step of a billet prior to semi-solid forging step is necessarily required to obtain globular microstructure. For the forming operation to work properly, it is also important to heat the billet uniformly for the uniformity of solid-liquid distribution. To satisfy these requirements, induction heating has been generally used for a long time. This paper presents the method to find heating condition and the temperature distribution inside a billet with a induction heating apparatus by comparing the computer simulation with experiment for aluminium alloys A12024 and A356.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.257-259
• /
• 2002

With development of Circuit technology, accuracy of dielectric or induction heating apparatus was developed. This study aims at realization of food insecticidal apparatus using dielectric heating. Equipment to measure grain's permittivity or vermin's permittivity and expectation for heating temperature by computer simulation is necessary for construction of the system. And the effect of extermination of vermin for food was confirmed by experiment using the system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 추계학술대회 논문집
• /
• pp.133-135
• /
• 2007

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Pull)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 학술대회 논문집 전문대학교육위원
• /
• pp.119-124
• /
• 2007

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Pull)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 추계학술대회 논문집
• /
• pp.241-243
• /
• 2008

This research presented the new zero-current switching pulse width modulation SEPP(Single Ended Push-Full)high frequency inverter for solving the problem of the zero-current SEPP high frequency inverter circuit which is using widely in the practical application of an induction heating apparatus, the soft switching operation and power control are impossible when the lowest power supply in the zero-current switching pulse width modulation SEPP high frequency inverter. The inverter circuit which is attempted by on-off operation of a switch has the reduction effect of the power loss due to a soft switching and a high frequency switching. And it confirmed that the power regulation is possible continuously from 0.25[kW] until 2.84[kW] in the case the duty rate(D) changes from 0.08 to 0.3 under zero-current switching operating by a dissymmetry pulse width modulating control and the power conversion efficiency comes true the efficiency of 95[%]. Due to the result above, the ZCS PWM SEPP high frequency inverter will be effective as sources of an induction heating apparatus.