• 열처리공학회지
• /
• 제17권2호
• /
• pp.73-77
• /
• 2004

The efforts which increase the strength of the auto-body structure and decrease its weight lead to develop a new concept of part production systems, such as Post-Form Strengthening by induction heat treatment. In this study, several cold and hot-rolled sheet steels were used to find out optimum induction heat treatment conditions. After induction heat treatment, strength of heat-treated sheet steels was increased significantly compared with that of as-rolled steels. From these results, auto-body structure which has more light and safe has been made by using this induction hardening method.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1946-1950
• /
• 2007

Switch rail is a very important part on the railway track, which not only accounts for the safety of the passing trains but also greatly influences the speed of the train. The higher the speed and the loads of the train the more it demands on the properties of the switch rail. Research shows that the higher mechanical properties of switch rail the longer the service life. Induction heat treatment is a good way of improving the mechanical properties of metallic materials. But the switch rail's section area changes gradually across the lengthways, which is difficult for induction heating especially for the small section. And the mechanical property of small section of the switch rail is the most important for its service life. The induction heat treatment used past always brings the low hardness on small section which can cause low service life of switch for wearing, or too high hardness because of martensite microstructure which can cause the shelling or even breaking of the switch rail. To prolong the service life of switch rail by higher mechanical properties, we researched the improved induction heat treatment for switch rail by adjusting speed of heating, and adopting compressed air cooling. The results showed that switch rail obtain almost the same high hardness across the length way after the improved induction heat treatment, which is very helpful to extend the service life of switch rail.

• 열처리공학회지
• /
• 제26권5호
• /
• pp.233-240
• /
• 2013

Rapid and homogeneous heating in heat treatment has been a challenging engineering issue throughout a heating temperature over $1,000^{\circ}C$. Induction heating has been widely used in field of heat treatment compared with conventional heating system. Advantages in homogeneous heating, simple fabrication, and repeatable use can be efficiently made with the induction heater. In this paper, numerical analysis of an induction coil system for heat flux gauge heating is performed. The effect of configuration on the heating performance was considered in various cases of the coil radius, distance between the winding, relative height difference between the heat flux gauge and the coil, and the applied current frequency. Temperature distribution within the heat flux gauge at frequency-steady state was calculated with a finite element method. Sensitivity analysis was also performed and the relative importance of 2 key parameters; coil radius, distance between the winding, were taken as main contributors for induction heating.

• 열처리공학회지
• /
• 제5권1호
• /
• pp.23-31
• /
• 1992

It is investigated that Fe-C-N compound layer, defusion layer, and induction hardened layer produced by nitrocarburizing blend heat treatment in austenitic temperature with high frequency induction heating of mild steel specimen sprayed sursulf salt-bath. As the temperature of blend-heat treatment got increased, the thickness and hardness of compound layer and diffusion layer were increased. Compound layer(max. $35{\mu}m$), diffusion layer (max. 2.5mm) and induction hardened layer were gained in the shortest time 10 sec and in the case of $1000^{\circ}C$ total hardness depth of those was about 3.5mm. When the blend-heat treated specimen was reheated, maximum hardness of compound layer was dropped more than that of the reheated compound layer after sursulf treated, whereas hardness of diffusion layer was increased.

• 열처리공학회지
• /
• 제2권2호
• /
• pp.17-26
• /
• 1989

This study has been performed to investigate into some effects of the Sursulf treatment time and the traveling speed of surface hardening treatment on the hardness and the wear characteristics by applying the combined heat treating techniques of Sursulf process followed by induction hardening treatment to mild steel. It has been shown that increasing the Sursulf treatment time increases the case depth, but both hardness and wear resistance are not considerably improved. When the combined heat treating technique of high frequency induction heating after Sursulf treatment is applied, an improvement in case depth as well as wear resistance is obtained. In particular, the hardness in diffusion zone is greatly increased due mainly to the formation of martensite and possibly lower bainite. Iron oxides formed during induction heating and subsequent water spray cooling in the outermost part of compound layer may be considered to cause some increases in hardness and wear resistance.

• 열처리공학회지
• /
• 제22권2호
• /
• pp.108-115
• /
• 2009

• 열처리공학회지
• /
• 제22권1호
• /
• pp.34-45
• /
• 2009

• 한국정밀공학회지
• /
• 제32권6호
• /
• pp.563-570
• /
• 2015

In this paper, Finite Element Analysis (FEA) for gear heat treatment using simultaneous dual frequency (SDF) induction heating is conducted. To do this, thermal-electromagnetic coupled FE model is built. A two dimensional FE model of gear and heater is introduced to reduce computation time. For more time-efficient analysis, harmonic analysis for electromagnetic model is adopted and transient analysis model, for heat transfer model. Through the coupled analysis, it can be found that the proposed FE model can solve for SDF induction heating of gear and heat treatment parameters can also be determined.

• 열처리공학회지
• /
• 제15권5호
• /
• pp.228-233
• /
• 2002

The characteristics of the induction heating process are analyzed for the joint of nylon and metal. The temperature of metal surface is measured using thermocouples. The relations of temperature and induction heating parameters are analyzed. Heat equation models are constructed and the temperature distribution is predicted using Fluent. The effects of heating parameters on the joint strength are evaluated. Finally, the optimal parameters of induction heating process are proposed as 16kW and 6 seconds.

• 열처리공학회지
• /
• 제12권3호
• /
• pp.240-250
• /
• 1999