• Corrosion Science and Technology
• /
• v.10 no.6
• /
• pp.194-198
• /
• 2011

This is the first release of an interim report on the development of coating technology of Zn-Mg alloy layers on steel strip by EML-PVD (electromagnetic levitation - physical vapor deposition) process in an air-to-air type continuous PVD pilot plant. It intends to introduce a basic principle of the EML-PVD process together with the high speed PVD pilot plant built in Posco. Due to the agitation effect provided by the high frequency induction coil, simultaneous evaporation of Zn and Mg from a droplet could produce alloy coating layers with Mg content of 6% to 12% depending on the composition of the droplet inside the coil. For its superior corrosion resistance, Zn-Mg alloy coated steel would be a very promising material for automotive, electrical appliances, and construction applications.

• Progress in Superconductivity and Cryogenics
• /
• v.11 no.2
• /
• pp.33-36
• /
• 2009

A 1 MW class HTS (High-Temperature Superconducting) synchronous motor has been developed. This motor is aimed to be utilized for industrial application such as large motors operating in large plants. The HTS field coil of the developed motor is cooled by way of neon thermo siphonmechanism and the stator (armature) coil is cooled by water through hollow copper conductor. This paper also describes evaluation of some electrical parameters from performance test results of our motor, which was conducted at steady state in generator mode and motor mode. Open and short circuit tests were conducted in generator mode while a 1.1 MW rated induction machine was rotating the HTS machine. Electrical parameters such as mutual inductance and synchronous inductance are deduced from these tests. Load test was done upto rating torque during motor mode and efficiency was measured at each load torque.

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.2
• /
• pp.82-87
• /
• 2022

The PZT piezoelectric ceramic on the copper alloy plate shows a extraordinary pattern resulted from the electromagnetic and thermal radiation induced by copper coil. The Eddy current or magnetic field by the polarization of PZT grains contained Pb, Zr, Ti with oxide is performed to show the change of array pattern at piezoelectric grains, especially wave-shaped or wrinkled configuration along with lines of electromagnetic field are becoming larger than before while applying the coil induction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.5
• /
• pp.305-311
• /
• 2016

Induction heating is the process in which an electrically conducting object (usually a metal) is heated by electromagnetic induction through heat generated in the object by eddy currents. The main advantage of an induction heating device is the generation of the heat inside the target object itself. Hence, non-contact and safe heating devices are widely used in many industrial and medical fields. Recently, a new dental implant system was developed using a shape-memory alloy, wherein an artificial tooth could be easily removed from the dental implant by heating. This paper discusses the development of an induction-heating device to remove the dental crown in the new implant system. First, the finite element simulation of electromagnetic and thermal coupling analysis was implemented to obtain the temperature distributions of the target object for various frequencies, input currents, and coil shapes. Based on the simulation results, experiments were conducted by using prototypes, and an induction heating device was developed to remove the dental crown from the implant.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.3-6
• /
• 2001

This paper designs a drive for high efficiency of the 3-phase IM (induction motor) for FCU(Fan Coil Unit). The speed control system of 3-phase IM for FCU has been implemented by a TMS320LF2406 DSP chip. The DSP TMS320LF2406, which include the most peripheral circuit for control of the Industrial motor suitable for AC motor drive. This type of the controller can be obtained low cost and high reliance. The proposed drive system of the 3-phase IM for the FCU is verified by simulation. The results show the speed control characteristics of the control strategy Proposed for 3-Phase IM drive.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.1099-1100
• /
• 2008

In this paper, we would like to introduce a simple and low cost wired pointing device by using a electromagnetic induction. A number of patents of Wacom describe electronic drawing devices or styluses. The movement of the stylus over a tablet is traced electronically and used applied to a resonant circuit in the stylus. Electromagnetic radiation emitted by the resonant circuit is detected by a sensing mechanism and location processing is used to locate the stylus. In this research, difference coil principle is used to detect the emitted radiation of the resonant circuit in the pen. This detection device shows good performance to detect the location of the pen on the tablet.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.48-55
• /
• 2010

We have development the steering angle sensor using not only detecting parts but also integrating technique with semiconductors for automobile applications. The performance design and analysis of the steering angle sensor for intelligent vehicles is complicated due to variety of parameters. In this study, the performance characteristics of the angle sensor were analyzed using test rig. By means of magnetic induction technique, these new the steering angle sensors showed excellent magnetic characteristics. The detection range of steering angle sensor obtained was ${\pm}800^{\circ}$, the maximum non-linearity is 0.744% Full Span and the temperature range was $-40^{\circ}C{\sim}+125^{\circ}C$. With this conclusive, the inductive angle sensor was quite satisfactory for many applications in intelligent vehicles.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.6-8
• /
• 1998

This paper deals with the maximum output power generation using the Dounly Fed Induction Generator(DFIG) in the super-synchronous speed regions, by control of both magnitude and phase of the voltage fed to the rotor. Steady-state algebraic equations of the euivalent circuit are solved using numerical analysis. For the normal operating region, in which the generator ratings are not exceeded, rotor current is less than or equal to the rated value. By selecting the permisible rated current at rotor coil, there are the optimal solution existng which covers the magnitude and phase of the injected voltage to the rotor for the given slip. This optimal solution is pointing out how the maximum output power can be carried out.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1037-1039
• /
• 2002

가전산업과 연계하여 유도가열 기술을 응용한 대표적인 시스템으로 IH압력밥솥을 예로 들 수 있다. 유도가열 코일에서 고주파 자속의 의해 발생된 와전류가 결합된 밥솥을 가열하기 때문에 유도가열 코일에는 고주파 손실을 줄이기 위해 Litz wire가 사용된다 이에 본 논문은 특히 IH압력밥솥에 사용되는 Litz wire를 선정하는 데 있어 중요한 요소가 되는 소선경, 가닥수별 AC DC 저항 및 손실계산 그리고 Cost 예측 방법을 제안한다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.849_850
• /
• 2009

본 논문에서는 mass heating에 적용되는 고주파 유도가열 코일의 형상설계에 대한 내용을 기술하였다. 고주파 전류가 흐르는 가운데, workpiece가 가장 고른 열분포 특성을 가질 수 있도록 가열시킬 수 있는 코일의 형태를 결정하는 과정을 나타내고 있다. 이를 설명하기 위해 유한요소법을 이용하여 와전류와 열전도 등의 결과를 데이터화하고 각 결과들의 순환적 재입력으로 수치들의 변화를 시각적으로 나타내어 제안된 코일 형상에 대한 효율성을 입증한다. 연구의 과정은 3차원 유한 요소 프로그램인 ANSYS로 이루어진다.