• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.122-129
• /
• 2017

For the production of a high-density ITO target, $In_2O_3$ powders with a small particle size and low agglomeration should be synthesized. The purpose of this study is to control the size and shape of the Indium hydroxide precursor which affects the properties of the $In_2O_3$ powder. As a starting raw material, Indium metal was dissolved in a Nitric acid ($HNO_3$) solution. The effect of concentration, pH, and temperature on the properties of Indium hydroxide was investigated using ammonium hydroxide as a precipitant. Crystallite size of each sample was analyzed by X-ray diffraction and the shape and the size of the powder was analyzed by transmission electron microscopy. As a result, the particle size of Indium hydroxide was increased with increase in the concentration of $In(NO_3)_3$ and the particle size and shape of the Indium hydroxide remained unchanged with increase in the pH of the solution. The particle size increased with increase in the precipitation temperature during precipitation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.2
• /
• pp.91-97
• /
• 2018

Indium hydroxide powder was prepared by precipitation method. The reaction temperature ($150{\sim}250^{\circ}C$) and the holding time at each reaction temperature (1~72 h) were used as experimental variables. The particle size, microstructure and crystal phase of each prepared powder were observed through X-ray diffraction (XRD), Transmission electron microscope (FE-TEM) and BET. In this study, we investigated the phase and microstructural change induced by heat treatment of indium hydroxide nanoparticles at various temperatures for different holding times.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.50-55
• /
• 2017

Determination of trace elements in a sample including complicated matrix is very difficult due to the interference by the matrix. Therefore, if the trace elements can be separated from the complex sample matrix and determined, the interference effects can be reduced, and it is very helpful for the overall analysis. In this study, the analytes of trace elements were separated from the sample matrix by co-precipitation with trace elements using indium hydroxide ($In(OH)_3$), then detected by inductively coupled plasma-atomic emission spectrometer (ICP-AES). Above all, the optimal conditions for the co-precipitation of elements with indium hydroxide were experimentally established. At last, salt was analyzed by the developed analytical method. No heavy metals were not found in Shinan Jeungdo salt, but trace amounts of several heavy metals except for cadmium were found in Cheonnam Yongkwang salt.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.63-67
• /
• 2014

Gallium is an important material and is used by industry of oxide semi-conductor and LED chip. However, the most of the gallium-containing waste resources became outflow abroad and the most of which is imported from oversea by following technical problem and low circulation rate. In this research, the recovery of high purity Gallium metal from Gallium scrap, which containing about 30% of Gallium, was investigated by using hydro-metallurgical process. As pretreatment, the Gallium scrap was pulverized and leached by strong acid such as hydro chloric acid. At the leached solution, Indium was separated as an Indium sponge by substitution reaction and then Gallium and Zinc hydroxide separated and filtrated using strong alkaline solution such as sodium hydroxide by precipitation method. Also, Gallium metal and Zinc metal was recovered by electrowinning method. To make an electrolytic solution, Gallium and Zinc hydroxide was leached by strong alkaline solution. Finally, High purity Gallium metal was recovered by vacuum refining process to remove the Zinc impurity.

• Korean Journal of Materials Research
• /
• v.21 no.8
• /
• pp.432-438
• /
• 2011

In this study, chemical bath deposited (CBD) indium sulfide buffer layers were investigated as a possible substitution for the cadmium sulfide buffer layer in CIGS thin film solar cells. The performance of the $In_2S_3$/CIGS solar cell dramatically improved when the films were annealed at $300^{\circ}C$ in inert gas after the buffer layer was grown on the CIGS film. The thickness of the indium sulfide buffer layer was 80 nm, but decreased to 60 nm after annealing. From the X-ray photoelectron spectroscopy it was found that the chemical composition of the layer changed to indium oxide and indium sulfide from the as-deposited indium hydroxide and sulfate states. Furthermore, the overall atomic concentration of the oxygen in the buffer layer decreased because deoxidation occurred during annealing. In addition, an In-thin layer was inserted between the indium sulfide buffer and CIGS in order to modify the $In_2S_3$/CIGS interface. The $In_2S_3$/CIGS solar cell with the In interlayer showed improved photovoltaic properties in the $J_{sc}$ and FF values. Furthermore, the $In_2S_3$/CIGS solar cells showed higher quantum efficiency in the short wavelength region. However, the quantum efficiency in the long wavelength region was still poor due to the thick buffer layer.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.5
• /
• pp.422-427
• /
• 1995

In a stream of water sample, trace metal ions are quantitatively coprecipitated with Indium hydroxide and filtered. The filtered precipitate is continuously dissolved in 3 M nitric acid and introduced to ICP directly. The lead, cadmium, and copper are concentrated more than 10-fold and determined with ICP-AES at a sampling frequency of 10/hour. The detection limits are 2.89, 1.43,0.52 ppb for lead, cadmium, and copper respectively. Recoveries of lead, cadmium, and copper are 98.7, 94.3, and 104.5% respectively. The RSD values for three elements are about 3-5% currently.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.163-167
• /
• 2002

Improved optical switching property of electrochromic nickel hydroxide/nickel glass thin film is reported. Nickel metal film was deposited on glass by e-beam evaporation before following electrochemical redox cycling to form nickel hydroxide for electrochromic activation. Without ITO (indium tin oxide) layer as electrical conductor, this electrode showed more rapid coloration rate than nickel hydroxide film on ITO substrate in the change of the electric voltage and optical transmittance. XPS analysis confirmed the existence of ultra-thin nickel metal layer (${\sim}10{\AA}$) between electrochemically grown nickel hydroxide and the glass substrate. It is concluded that the remained nickel metal nano-layer attribute to the conduction layer and the enhanced response time.

• Journal of Sensor Science and Technology
• /
• v.10 no.2
• /
• pp.101-107
• /
• 2001

A highly selective, sensitive and reliable ozone sensing $In_2O_3$ thin film was fabricated by a sol-gel method. The fabricated film is operated at a relatively lower temperature than ever developed thin films and saved operating power. $In_2O_3$ films deposited by sol-gel technique has been recently attracted because it is an economical and energy saving method and precisely controlled microstructure. Indium alkoxide precursor was synthesized from the reaction between indium hydroxide and butanol. PVA binder was used to improve adhesion of the films. The $In_2O_3$ thin films were obtained by spin coating from 1 to 5 times followed by drying at $100^{\circ}C$ and calcining at $600^{\circ}C$ for 1h. The film thickness was controlled by the number of coating time. The morphology and the thickness of the $In_2O_3$ films were examined by a SEM and XRD. The $In_2O_3$ thin films show a high sensitive to ozone gas at operating temperature of $250^{\circ}C$. The $In_2O_3$ sensor has very good selectivity to $CH_4$, CO, $C_4H_{10}$ and ethanol.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.705-716
• /
• 2017

In this study, Indium-Titanium hydroxide particle with 0.5, 1.0, 1.5 wt% of $TiO_2$ were synthesized by sol process and adding the base, ITiO(Indium Titanium Oxide) particles were obtained by gelling at $200^{\circ}C$ and $500^{\circ}C$. The ITiO particle's size with gel process at $200^{\circ}C$ was smaller than ITiO particle's size with gel process $500^{\circ}C$. The ITiO particle with gel process at $200^{\circ}C$ was used to fabricate dense ITiO target. ITiO targets with 0.5, 1.0, 1.5 wt% of $TiO_2$ were fabricated and used to obtain ITiO thin films onto glass by sputtering. Among those sputtered ITiOs' thin films, ITiO thin film with 0.4 % of $O_2$ and 0.5 wt% of $TiO_2$ showed the lowest specific resistance, highest charge mobility and lowest carrier concentration. It was found the light transmittance of the ITiO film were increased highly compared to light transmittance of ITO (Indium Tin Oxide) thin film over Infrared wavelength ranges.

• Applied Science and Convergence Technology
• /
• v.23 no.4
• /
• pp.187-191
• /
• 2014

Indium oxide ($In_2O_3$) nanorods (NRs) which can be expected to increase the device performance in various electronic and electrochemical applications were prepared on carbon fibers via an electrochemical deposition (ED) method. During the ED, the indium hydroxide ($In(OH)_3$) NRs were well grown and firmly attached onto the carbon fibers. After that, they were changed into $In_2O_3$ by dehydration through a thermal annealing. The morphological and structural properties were investigated using field-emission scanning electron microscope images. The crystallinity of as-prepared sample was evaluated by X-ray diffraction. The Fourier transform infrared results confirm that the functional groups are present in the $In_2O_3$ NRs. This facile process of metal oxide nanostructures on carbon fiber can be utilized for flexible electronic and energy related applications.