창업 멘토링 기능이 창업의지와 멘토링 만족도에 미치는 영향: 오퍼스 창업교육을 중심으로 (The Effects of Entrepreneurship Mentoring on Entrepreneurial Will and Mentoring Satisfaction: Focusing on Opus Entrepreneurship Education)
-
- 벤처창업연구
- /
- 제18권3호
- /
- pp.211-226
- /
- 2023
포스트 코로나 시대에 접어들면서 그 동안 움츠렸던 경제활동들이 다시 활발해지고 있다. 특히 4차 산업혁명 시대 디지털 전환의 기회에 따른 기술창업이 증가되는 추세이지만 창업 교육 콘텐츠는 기술적인 변화의 속도를 따라가지 못하고 있다. 본 연구는 기술창업의 수요 증가로 변화와 발전이 요구되는 창업교육 콘텐츠 중에서 창업 멘토링의 중요성을 확인하고자 한다. 창업 멘토링은 예비창업자와 초기창업자들의 창업 성공을 위해 전문 역량을 보유한 멘토가 멘티들의 수준에 맞게 맞춤형으로 성취 동기, 경영 기술, 문제 해결에 도움을 주는 행동으로 이미 대부분의 창업교육 프로그램에 구성요소로 포함되어 있다. 이를 위해 멘토링 기능 중 멘티의 창업지식과 자기 효능감을 독립변수로 설정하고, 창업의지와 멘토링 만족도를 종속변수로 설정한 후 교육생의 창업 여부를 예비 창업가와 초기 창업가로 분류, 조절변수로 설정하여 연구모형을 설계하고 가설을 설정하였다. 그리고 ICCE 창업스쿨 및 오퍼스 창업스쿨에서 창업 멘토링 교육생들을 대상으로 설문조사를 실시하여 실증적 분석을 진행하였다. 실증 분석 결과를 요약해보자면 첫 번째, 창업 멘토링 기능 중 창업지식과 자기 효능감은 창업의지에 유의적인 정(+)의 영향을 주는 것으로 분석되었다. 두 번째, 창업 멘토링 기능 중 창업지식과 자기 효능감은 멘토링 만족도에 유의적인 정(+)의 영향을 주는 것으로 분석되었다. 세 번째, 창업 여부는 창업지식과 창업의지에 유의미한 조절효과가 없다고 분석되었다. 네 번째, 창업 여부는 멘토링 만족도에 유의미한 조절효과가 없다고 분석되었다. 다섯 번째, 창업 여부가 자기 효능감과 창업의지 사이에 유의미한 조절효과가 있는 것으로 나타났다. 연구 분석 결과를 통해 본 시사점은 첫 번째로 창업교육에서 멘토링기능은 초기 창업가와 예비 창업가 모두에게 창업의지와 만족도에 유의미한 성과를 내는 것으로 분석되어 앞으로도 모든 창업교육에서 멘토링을 적극적으로 활용해야 할 것으로 보인다. 두 번째로 창업 여부와 멘토링기능 및 효과는 대체로 별다른 관련이 없는 것으로 분석되었다. 하지만 멘토링을 통한 자기 효능감 향상을 통한 창업의지는 창업 여부와 유의미한 관련이 있는 것으로 분석되었고, 멘토들이 멘토링을 진행할 때 멘티의 창업 여부를 확인하고 맞춤형 멘토링을 하는 것이 더 큰 자기 효능감과 창업의지를 갖게 하는데 도움이 된다고 나타났다. 현재 국내에서 진행되는 많은 창업교육들은 편의성 등을 이유로 초기 창업가와 예비 창업가를 동시에 교육하고 있다. 하지만 본 연구결과를 통해 소규모로 진행되는 창업 멘토링에서라도 멘티의 창업 여부와 같은 세부적인 분류를 통해 맞춤형 멘토링을 진행하는 것이 멘티의 성공적인 창업과 높은 만족도를 위한 방법이 될 수 있다는 방안을 제시하였다.
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
본(本) 연구(硏究)는 계획기간내(計劃期間內)의 재적수확량(材積收穫量)을 최대화(最大化)하고 각분기(各分期)의 수확량(收穫量)과 수확면적(收穫面積)을 일정(一定) 범위(範圍)로 제약(制約)하여 계획기간내(計劃期間內)의 보속수확(保續收穫)을 도모(圖謀)하는 동시(同時)에 후계림(後繼林)의 법정영급배치(法正令級配置)가 유도(誘導)될 수 있는 적정수확안(適正收穫案)을 선형계획법(線型計劃法)에 의하여 선정(選定)하고, 제약량(制約量)의 변화(變化)가 총수확량(總收穫量) 및 분기별(分期別) 수확량(收穫量)과 수확면적(收穫面積)에 미치는 영향(影響)을 구명(究明)하는데 목적(目的)이 있다. 서울 대학교(大學校) 농과대학(農科大學) 부속연습림중(附屬演習林中) 개벌작업급(皆伐作業級)에 속하는 219개(個) 소반(小班)을 대상(對象)으로 하였으며, 이 삼림(森林)은 영급구성면(令級構成面)에서 볼 때 유영급(幼令級) 임분(林分)이 많다는 점(點)에서 전국(全國) 삼림(森林)을 대표(代表)한다고 할 수 있다. 본(本) 연구(硏究)에서는 한 분기년수(分期年數)를 5년(年), 계획기간(計劃期間)을 10분기(分期), 1영급(令級)을 5영개(令皆)로 하였으며, 벌채영급(伐採令級)의 범위(範圍)는 5~9영급(令級)이다. 한편, 후계림(後繼林)은 현실림(現實林)이 수확(收穫)되는 즉시 조림(造林)되고, 미립목지(未立木地)는 1분기내(分期內)에 조림(造林)되며 다음 벌기(伐期)까지 충분(充分)한 입목도(立木度)가 이루어지는 것으로 전제(前提)하였다. 소반(小班)을 벌구(伐區)로 하여, 각벌구(各伐區)가 계획기간내(計劃期間內)에 벌채(伐採)될 수 있는 모든 가능(可能)한 대체수확안(代替收穫案)을 그의 영급(令級)에 따라 작성(作成)하고, 여기에 현실림(現實林)과 후계림(後繼林)의 벌기예상수확량(伐期豫想收穫量)을 대입(代入)하여 각대체안(各代替案)의 계획(計劃) 기간내(期間內) 수확량(收穫量)(
The objective of this research is to test the feasibility of developing a statewide truck traffic forecasting methodology for Wisconsin by using Origin-Destination surveys, traffic counts, classification counts, and other data that are routinely collected by the Wisconsin Department of Transportation (WisDOT). Development of a feasible model will permit estimation of future truck traffic for every major link in the network. This will provide the basis for improved estimation of future pavement deterioration. Pavement damage rises exponentially as axle weight increases, and trucks are responsible for most of the traffic-induced damage to pavement. Consequently, forecasts of truck traffic are critical to pavement management systems. The pavement Management Decision Supporting System (PMDSS) prepared by WisDOT in May 1990 combines pavement inventory and performance data with a knowledge base consisting of rules for evaluation, problem identification and rehabilitation recommendation. Without a r.easonable truck traffic forecasting methodology, PMDSS is not able to project pavement performance trends in order to make assessment and recommendations in the future years. However, none of WisDOT's existing forecasting methodologies has been designed specifically for predicting truck movements on a statewide highway network. For this research, the Origin-Destination survey data avaiiable from WisDOT, including two stateline areas, one county, and five cities, are analyzed and the zone-to'||'&'||'not;zone truck trip tables are developed. The resulting Origin-Destination Trip Length Frequency (00 TLF) distributions by trip type are applied to the Gravity Model (GM) for comparison with comparable TLFs from the GM. The gravity model is calibrated to obtain friction factor curves for the three trip types, Internal-Internal (I-I), Internal-External (I-E), and External-External (E-E). ~oth "macro-scale" calibration and "micro-scale" calibration are performed. The comparison of the statewide GM TLF with the 00 TLF for the macro-scale calibration does not provide suitable results because the available 00 survey data do not represent an unbiased sample of statewide truck trips. For the "micro-scale" calibration, "partial" GM trip tables that correspond to the 00 survey trip tables are extracted from the full statewide GM trip table. These "partial" GM trip tables are then merged and a partial GM TLF is created. The GM friction factor curves are adjusted until the partial GM TLF matches the 00 TLF. Three friction factor curves, one for each trip type, resulting from the micro-scale calibration produce a reasonable GM truck trip model. A key methodological issue for GM. calibration involves the use of multiple friction factor curves versus a single friction factor curve for each trip type in order to estimate truck trips with reasonable accuracy. A single friction factor curve for each of the three trip types was found to reproduce the 00 TLFs from the calibration data base. Given the very limited trip generation data available for this research, additional refinement of the gravity model using multiple mction factor curves for each trip type was not warranted. In the traditional urban transportation planning studies, the zonal trip productions and attractions and region-wide OD TLFs are available. However, for this research, the information available for the development .of the GM model is limited to Ground Counts (GC) and a limited set ofOD TLFs. The GM is calibrated using the limited OD data, but the OD data are not adequate to obtain good estimates of truck trip productions and attractions .. Consequently, zonal productions and attractions are estimated using zonal population as a first approximation. Then, Selected Link based (SELINK) analyses are used to adjust the productions and attractions and possibly recalibrate the GM. The SELINK adjustment process involves identifying the origins and destinations of all truck trips that are assigned to a specified "selected link" as the result of a standard traffic assignment. A link adjustment factor is computed as the ratio of the actual volume for the link (ground count) to the total assigned volume. This link adjustment factor is then applied to all of the origin and destination zones of the trips using that "selected link". Selected link based analyses are conducted by using both 16 selected links and 32 selected links. The result of SELINK analysis by u~ing 32 selected links provides the least %RMSE in the screenline volume analysis. In addition, the stability of the GM truck estimating model is preserved by using 32 selected links with three SELINK adjustments, that is, the GM remains calibrated despite substantial changes in the input productions and attractions. The coverage of zones provided by 32 selected links is satisfactory. Increasing the number of repetitions beyond four is not reasonable because the stability of GM model in reproducing the OD TLF reaches its limits. The total volume of truck traffic captured by 32 selected links is 107% of total trip productions. But more importantly, ~ELINK adjustment factors for all of the zones can be computed. Evaluation of the travel demand model resulting from the SELINK adjustments is conducted by using screenline volume analysis, functional class and route specific volume analysis, area specific volume analysis, production and attraction analysis, and Vehicle Miles of Travel (VMT) analysis. Screenline volume analysis by using four screenlines with 28 check points are used for evaluation of the adequacy of the overall model. The total trucks crossing the screenlines are compared to the ground count totals. L V/GC ratios of 0.958 by using 32 selected links and 1.001 by using 16 selected links are obtained. The %RM:SE for the four screenlines is inversely proportional to the average ground count totals by screenline .. The magnitude of %RM:SE for the four screenlines resulting from the fourth and last GM run by using 32 and 16 selected links is 22% and 31 % respectively. These results are similar to the overall %RMSE achieved for the 32 and 16 selected links themselves of 19% and 33% respectively. This implies that the SELINICanalysis results are reasonable for all sections of the state.Functional class and route specific volume analysis is possible by using the available 154 classification count check points. The truck traffic crossing the Interstate highways (ISH) with 37 check points, the US highways (USH) with 50 check points, and the State highways (STH) with 67 check points is compared to the actual ground count totals. The magnitude of the overall link volume to ground count ratio by route does not provide any specific pattern of over or underestimate. However, the %R11SE for the ISH shows the least value while that for the STH shows the largest value. This pattern is consistent with the screenline analysis and the overall relationship between %RMSE and ground count volume groups. Area specific volume analysis provides another broad statewide measure of the performance of the overall model. The truck traffic in the North area with 26 check points, the West area with 36 check points, the East area with 29 check points, and the South area with 64 check points are compared to the actual ground count totals. The four areas show similar results. No specific patterns in the L V/GC ratio by area are found. In addition, the %RMSE is computed for each of the four areas. The %RMSEs for the North, West, East, and South areas are 92%, 49%, 27%, and 35% respectively, whereas, the average ground counts are 481, 1383, 1532, and 3154 respectively. As for the screenline and volume range analyses, the %RMSE is inversely related to average link volume. 'The SELINK adjustments of productions and attractions resulted in a very substantial reduction in the total in-state zonal productions and attractions. The initial in-state zonal trip generation model can now be revised with a new trip production's trip rate (total adjusted productions/total population) and a new trip attraction's trip rate. Revised zonal production and attraction adjustment factors can then be developed that only reflect the impact of the SELINK adjustments that cause mcreases or , decreases from the revised zonal estimate of productions and attractions. Analysis of the revised production adjustment factors is conducted by plotting the factors on the state map. The east area of the state including the counties of Brown, Outagamie, Shawano, Wmnebago, Fond du Lac, Marathon shows comparatively large values of the revised adjustment factors. Overall, both small and large values of the revised adjustment factors are scattered around Wisconsin. This suggests that more independent variables beyond just 226; population are needed for the development of the heavy truck trip generation model. More independent variables including zonal employment data (office employees and manufacturing employees) by industry type, zonal private trucks 226; owned and zonal income data which are not available currently should be considered. A plot of frequency distribution of the in-state zones as a function of the revised production and attraction adjustment factors shows the overall " adjustment resulting from the SELINK analysis process. Overall, the revised SELINK adjustments show that the productions for many zones are reduced by, a factor of 0.5 to 0.8 while the productions for ~ relatively few zones are increased by factors from 1.1 to 4 with most of the factors in the 3.0 range. No obvious explanation for the frequency distribution could be found. The revised SELINK adjustments overall appear to be reasonable. The heavy truck VMT analysis is conducted by comparing the 1990 heavy truck VMT that is forecasted by the GM truck forecasting model, 2.975 billions, with the WisDOT computed data. This gives an estimate that is 18.3% less than the WisDOT computation of 3.642 billions of VMT. The WisDOT estimates are based on the sampling the link volumes for USH, 8TH, and CTH. This implies potential error in sampling the average link volume. The WisDOT estimate of heavy truck VMT cannot be tabulated by the three trip types, I-I, I-E ('||'&'||'pound;-I), and E-E. In contrast, the GM forecasting model shows that the proportion ofE-E VMT out of total VMT is 21.24%. In addition, tabulation of heavy truck VMT by route functional class shows that the proportion of truck traffic traversing the freeways and expressways is 76.5%. Only 14.1% of total freeway truck traffic is I-I trips, while 80% of total collector truck traffic is I-I trips. This implies that freeways are traversed mainly by I-E and E-E truck traffic while collectors are used mainly by I-I truck traffic. Other tabulations such as average heavy truck speed by trip type, average travel distance by trip type and the VMT distribution by trip type, route functional class and travel speed are useful information for highway planners to understand the characteristics of statewide heavy truck trip patternS. Heavy truck volumes for the target year 2010 are forecasted by using the GM truck forecasting model. Four scenarios are used. Fo~ better forecasting, ground count- based segment adjustment factors are developed and applied. ISH 90 '||'&'||' 94 and USH 41 are used as example routes. The forecasting results by using the ground count-based segment adjustment factors are satisfactory for long range planning purposes, but additional ground counts would be useful for USH 41. Sensitivity analysis provides estimates of the impacts of the alternative growth rates including information about changes in the trip types using key routes. The network'||'&'||'not;based GMcan easily model scenarios with different rates of growth in rural versus . . urban areas, small versus large cities, and in-state zones versus external stations. cities, and in-state zones versus external stations.
우리나라에서는 일본잎갈나무가 대량(大量) 조림(造林)되어 축적(蓄積)과 생장량(生長量)으로 보아 주요(主要)한 조림(造林) 수종(樹種)이나 각종(各種) 추출물(抽出物)과 활성(活性) phenol 성분(成分)이 많고 심재율(心材率)이 높아 펄프화(化)에서 수율저하(收率低下)와 표백곤란(漂白困難)이 초래(招來)되어 펄프원료(原料)로서의 이용(利用)이 기피(忌避)되고 있다. 따라서 일본잎갈나무의 화학(化學)펄프 원료화(原料化)의 제고(提高)로서 펄프수율(收率) 향상(向上)과 표백성(漂白性) 개선(改善)을 위하여 셀룰로오스보호제를 첨가(添加)한 소다펄프화(化) 특성(特性)을 구명(究明)하였다. 증해(蒸解)는 최고온도(最高溫度) 170
대기업과 중소기업의 갈등이 심화되고 있고 낙수효과 또한 제대로 작동하지 않고 있으며 사업조정제도의 실효성에 대한 논란이 이어지고 있는 가운데 중소기업의 사업영역을 보호하고 중소 대기업간 양극화를 해소하며 더불어 골목상권도 보호하기 위한 방안으로 도입된 것이 중소기업 적합업종 지정제도이다. 중소기업 적합업종의 추진현황은 제조업분야로 중소기업 적합업종 품목 중 234개 품목을 신청 접수 받아 실태조사 및 분석하여 조정협의체의 품목을 선정하였다. 서비스업분야에서의 적합업종 지정은 사회적 갈등이 있는 업종부터 지정할 계획인데, 중소기업 및 소상공인의 생업과 관련된 3개 대분류 서비스업종을 대상으로 우선 지정하고 추후 순차적으로 확대할 예정이다. 하지만 중소기업 적합업종 품목으로 선정될 경우에는 중소기업의 성장 동기가 저해될 우려가 있으며, 중소기업 적합업종 품목 지정은 소비자 후생 감소가 나타날 수 있다. 또한 사전적 규제로 작용할 소지가 높을 뿐만 아니라 경쟁을 제도적으로 제한함으로써 부작용이 나타날 우려가 있으며 FTA 체제의 주요 규정에 대한 위배 가능성도 있다. 뿐만아니라 대기업에 대한 역차별 요인이 충분히 반영되지 않고 있다는 점도 문제점으로 지적된다. 특히 중소기업 적합업종제도가 대기업의 주력분야와 관계없는 서비스업에 대한 진출 확대로 인해 중소기업 및 소상공인과의 갈등을 초래하고 있는 실정이므로 중소기업이나 중소상인의 보호를 위해서는 프랜차이즈시스템을 통해서 지역 중소기업을 발전시키고 마스터 프랜차이즈나 지역 프랜차이즈 시스템과 같은 선진 계약 방식을 도입하는 것이 필요하다. 하지만 이러한 방식은 기업들의 경쟁력과 운영방식을 한층 더 진일보 시켜 중소 프랜차이즈기업의 경쟁력 강화에 기여하는 효과도 있지만 부정적 측면이 더 많다고 볼 수 있다. 첫째, 지식경제부가 밝히고 있듯이, 프랜차이즈산업은 자영업자의 창업 성공률을 높여주고, 기존 자영업자를 조직화하여 규모의 경제를 통한 경쟁력 강화에 기여할 뿐만 아니라 다양한 서비스를 소비자에게 제공함으로써 내수시장을 확대하고, 일자리 창출에 기여하는 등 자영업자 경쟁력 제고와 서비스 산업 활성화를 위한 '유용한 수단'임을 강조하고 정부 서민안정 대책으로 밝힌바 있다. 이러한 관점에서 본다면, 프랜차이즈는 적합업종 제도의 취지에 부합하는 것이며 이에 반하는 것이 아님을 알 수 있다. 둘째, 적합업종으로 지정될 경우 국제적 경쟁력을 갖고 있는 국내 프랜차이즈 대기업들의 위축과 사기저하로 인하여 해외진출과 R&D, 식품안전에 대한 투자 감소와 더불어 국내 진출한 해외 기업들의 사업 확장에 부정적 영향을 끼칠 수 있다. 또한 국내 진출한 다국적 해외 프랜차이즈기업들과의 경쟁력을 확보하는 것이 무엇보다도 시급한 국내 프랜차이즈산업 현실에서 국제적 경쟁력 확보의 어려움뿐만 아니라 국내에 진출한 해외 프랜차이즈기업들과의 역차별이 발생할 수도 있다. 셋째, 중소기업 적합업종 품목 지정은 지금까지 제품을 사용해 왔던 소비자들의 선택의 기회를 제한함과 동시에 소비자의 후생을 감소시키는 부정적인 효과를 초래한다. 또한 중소기업 간의 역차별 문제를 발생시켜 소수 중소기업이 시장을 독점함으로써 소비자 선택의 폭이 줄어들 가능성이 있으므로 제품의 효용을 판단하는 역할은 국가가 아닌 소비자의 몫으로 남겨두어야 한다. 마지막으로는 프랜차이즈와 관련하여 이미 가맹사업법과 그리고 공정거래위원회의 모범거래기준 등의 시행으로 공정거래는 확보하고 있으므로 앞으로도 부족한 부분은 이들을 보완하여 진행하는 것이 바람직하다고 본다. 중소기업 적합업종 지정으로 이중삼중으로 규제하는 것은 오히려 프랜차이즈 분야에 과도한 제한이 될 것이다. 이제 국내 프랜차이즈산업에서도 한국의 문화를 전파하는 세계적 프랜차이즈기업이 성장할 수 있는 환경조성과 정부의 적극적인 지원이 필요하다. 따라서 프랜차이즈 기업의 성장 과정이나 배경을 고려하지 않고 현재 대기업이라는 이유만으로 이들에게 불이익을 주는 일은 없어야 한다. 프랜차이즈기업의 성장억제로 인하여 결국 가맹점의 매출감소는 물론이고 심지어는 폐업하는 가맹점의 숫자를 증가시키는 또 다른 문제를 발생시킬 수 있다는 것이다. 따라서 중소기업 적합업종제도가 대기업의 발목을 잡는 것이 아니라 소상공인과 중소기업의 경쟁력 제고와 동반성장을 목표로 하고 있는 만큼 대기업과 소상공인 및 중소기업이 상생과 협력을 바탕으로 거래관계를 지속하는 프랜차이즈 기업들이 포함되지 않도록 하는 것이 타당할 것이다.
본(本) 연구(硏究)의 공시(供試) 곡물(穀物)로서 벼 6 품종(品種)(Japonica 3 품종(品種), Indica
1994년 가을 한국을 방문하였을 때 놀란 것 온 도시 근교에 숲과 같이 세워진 고층 아파트 단지와 그 수요의 배경이 된 서울, 수원을 비롯한 수도권의 인구 집중이었다. 이러한 인구 집중을 가져온 것은 바로 제2차, 3차 산업의 발달이었다. 그 이후 6년만인 2000년 3월에 다시 농촌과 농촌지도사업의 변화 동향을 살펴보기 위하여 농가 방문, 도 농업기술원 및 시
본(本) 연구(硏究)는 우리나라 채석업체(採石業體)의 경영개선(經營改善)을 위한 기초자료(基礎資料)를 제공(提供)할 목적(目的)으로 실시(實施)되었다. 이를 위하여 골재용(骨材用) 채석업체(採石業體) 30개소(個所)와 건축용(建築用) 채석업체(採石業體) 46개소(個所)의 경영실태(經營實態)와 경영성과(經營成果), 생산요소(生産要素) 투입(投入)의 경제성(經劑性), 적정규모(適正規模) 등을 분석(分析)하였으며, 그 결과(結果)를 요약(要約)하면 다음과 같다. 1. 골재용(骨材用) 채석업체(採石業體)와 건축용(建築用) 채석업체(採石業體)의 경영주(經營主) 연령(年齡) 40재(才) 이상(以上)이 각각(各各) 97%, 89.1% 이었고, 고졸이상(高卒以上) 학력(學歷) 소지자(所持者)가 각각(各各) 90%, 85% 이었다. 또한, 경력면(經歷面)에서 10년(年) 이하(以下)의 경영주(經營主)는 골재용(骨材用) 채석업체(採石業體)에서 70%, 건축용(建築用) 채석업체(採石業體)에서 52% 이었다. 따라서, 두 채석업체(採石業體)에 대한 경영주(經營主)의 대부분(大部分)은 고령(高齡), 고학력(高學歷) 소지자(所持者)이며, 경력면(經歷面)에서는 골재용(骨材用) 채석업체(採石業體)가 건축용(建築用) 채석업체(採石業體)보다 다소 낮게 나타났다. 2. 골재용(骨材用) 채석업체(採石業體)에 대한 경영조직(經營組織)의 형태(形態)는 회사법인(會社法人)이 60%로 많은 반면(反面), 건축용(建築用) 채석업체(採石業體)는 개인업체(個人業體)가 76%로 많게 나타났다. 골재용(骨材用) 채석업체(採石業體)의 허가면적(許可面積)은 약(約) 2.86ha, 건축용(建築用) 채석업체(採石業體)는 1.66ha으로 나타났다. 여기에서, 골재용(骨材用) 채석업체(採石業體)가 건축용(建築用) 채석업체(採石業體)보다 큰 규모(規模)로 경영(經營)되고 있음을 알 수 있다. 3. 골재용(骨材用) 채석업체(採石業體)의 연평균(年平均) 채석량(採石量)은 1985년(年)의