• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.193-198
• /
• 2000

The small punch test have been developed to evaluate the material strength of the power plant components. This small punch test specimen is very small than the conventional strength test specimens. Korea Electric Power Research Institute (KEPRI) have been applying this test to assess accurately the life of thermal power plant and enhancing the reliability. The small punch test for gas turbine blades is under development. It's possible to compare the relative strength among the same materials having different operation histories. In this paper, the strength reductions of gas turbine materials are investigated by the small punch tests. All materials shows the almost same strength and deformation with the allowable deviation. At the same test temperature, the damaged material has the maximum load value. The strength reduction is not shown in this small punch test results.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.4
• /
• pp.271-281
• /
• 2003

The present article is concerned with pitting corrosion of Inconel alloy 600 at elevated solution temperatures. This article first summarized the previous works on the characteristics and the growth models of oxide film grown on alloy 600 at elevated solution temperatures. Thereafter, this article reviewed previous works on the morphological study on pitting corrosion of alloy 600 as functions of solution temperature and such anion additives as thiosulphate, sulphate, nitrate and bicarbonate ions in terms of pit morphology and its fractal dimension.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.78-83
• /
• 1999

Fretting Wear Behavior and Characteristics were investigated with Inconel 690 tube which is used in Nuclear Power Plant. Fretting Wear Tester has been engaged in the study of characteristics on tube fretted induced to various factors, i.e. vibration amplitude, contact type, material properties load support geometry, environmental effect Test has been performed in air and at room temperature. Wear volume rate has been approximately estimated as a function of normal load.

• Tribology and Lubricants
• /
• v.11 no.5
• /
• pp.78-86
• /
• 1995

The silicon nitride based ceramic cutting tool materials have been fabricated by gas pressure sintering (GPS) or hot pressing (HP). Their mechanical properties were measured and the effect of the fabrication variables on the properties were examined. Also, effect of adding TiN or TiC particulates on the mechanical properties of the silicon nitride ceramics were investigated. Ceramic cutting tools (ISO 120408) were made of the sintered bodies. Cutting performance test were performed on either conventional or NC lathe. The workpieces were grey cast iron, hardened alloy steel (AISI 4140, HRc>60) and Ni-based superalloy (Inconel 718). The results showed that fabrication variables, namely, sintering temperature and time, exerted a strong influence on the microstincture and mechanical properties of the sintered body, which, however, did not make much difference in wear resistance of the tools. High hardness of the tool containing TiC particulates exhibited good cutting performance. Extensive crater wear was observed on both monolithic and TiN-containing silicon nitride tools after cutting the hardened alloy steel. Inconel 718 was extremely difficult to cut by the current cutting tools.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.80-87
• /
• 1995

An experimental study of hot machining has performed to improve themachinability of Inconel 718. This experiment used plasma arc for heating materials and Whisker-reinforced aluminum oxide ceramic tool insert. An assembled plasma heating system are described and experimental results obtained from bothconventional and plasma hot machining of Iconel 718 are compared. Turning experiments with plasma heating demonstrated the following effectiveness. 1) The cutting force was reduced with increasing surface temperature of workpiece from 450 .deg. C up to 720 .deg. C as much as approximately from 20 to 40%. 2) Surface roughness(Ra) was improved by as much as a factor 2 in case of one pass cutting with new ceramic tool inserts. 3) The depth of cut notchwear at primarycutting tool was singificantly reduced.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.165-167
• /
• 2005

Compared with Inconel 625 (ERNiCrMo-3) weld, Nb-free Alloy 59 (ERNiCrMo-13) weld with 15% Mo showed much higher resistance to hot cracking. Especially in the condition of current 350A and 30CPM of welding speed, no crack was detected at Inconel 625 fillet weld. Furthermore, it was found that the strength of Alloy 59 is sensitive to welding heat input. Up to around 14kJ/cm of heat input, Alloy 59 showed 678N/$mm^{2}$ of ultimate strength and 466N/$mm^{2}$ of yield strength. However, as heat input increased above 14kJ/cm, Alloy 59 weld could not satisfy the weld strength required for European LNG tank.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.168-170
• /
• 2005

Nickel base brazes containing boron and silicon as melting point depressants are used extensively in the joining and repair of hot-section components in next generation nuclear reactor and aero-engine. Therefore, the present study has investigated the preliminary applicability of nickel based alloying nano powders. Nano Ni-based alloying powders synthesized by Pulsed Wire Evaporation (PWE) method. It's powder morphology and phase transformation temperature were analyzed by scanning electron microscopy, transmission electron microscopy, and differential scanning calorimeter(DSC). The powder particle size was approximately 10${\sim}$100nm and exhibits a quite even equiaxed shape. The results of DSC measurement show that both the nano Inconel 625 nano powder and Inconel 718 nano powder presents similar liquidus temperatures approximately $1373^{\circ}C$ and $1380^{\circ}C$ respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.356-356
• /
• 2011

탄소나노튜브(CNT)는 기계적, 전기적, 열적성질이 매우 우수하여 다양한 응용이 기대되고 있다. CNT를 금속기판에 직접 합성시킬 경우 CNT와 금속기판의 계면에서 높은 전도성 및 물리적 접착 강도를 기대할 수 있어서, 전계방출(field emission) 소자 또는 방열(heat dissipation) 소자 등과 같은 CNT의 높은 전도성과 일차원적 구조를 이용하고자 하는 분야로의 응용가능성을 높일 수 있다. 본 연구에서는 CNT의 합성촉매로 주로 사용되고 있는 니켈을 주요 성분으로 함유하고 있는 Inconel, Hastelloy, Invar 등을 합성기판으로 선정하여, CNT의 합성 거동을 조사하였다. CNT 합성은 CVD방법을 이용하였으며, 아세틸렌가스를 원료가스로 이용하였다. 합성 전 기판의산화 전처리가 CNT합성 효율에 영향을 미치는 것을 확인하였으며, 이를 체계적으로 조사하기 위하여, 다양한 온도(425~725$^{\circ}C$) 구간에서 산화 전처리를 실시한 후 CNT의 합성 거동을 조사하였다. 산화과정에 의한 표면구조의 변화 및 표면에서 금속성분의 재배열이 CNT합성 효율 변화의 원인으로 사료되고 있으며, 이를 분석하기 위해서, AFM, XRD, EDS, SEM, TEM 등을 이용하였다. 본 연구결과는 향후 전자방출소자, X-ray source 및 방열소자 등의 응용에 유용할 것으로 기대된다.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.42-44
• /
• 1996

이종재료인 2$\frac{1}{4}$Cr-1Mo강과 12Cr-1Mo-V계 강의 용접부의 용접성에 대하여 모재계열의 용접재료와 Inconel계의 용접재료를 사용하여 야금학적인 관점으로부터 미세조직적 특성 및 기계적성질을 중심으로 검토하였다. 그 결과를 요약하면 다음과 같다. (1) 본 연구의 실험범위에 의하면, 내부결함, 균열 등의 용접결함을 발생하지 않는 양호한 용접부를 얻을 수 가 있었다. (2) 광학현미경을 이용한 미세조직의 관찰에 의하면, Inconel계의 용접재료를 제외한 모재계열의 용접재료를 사용하였을 경우, 용융경계부 근방에서 연속 또는 불연속적인 백색의 밴드상이 형성되었다. (3)백색밴드상의 형성부는 인장변형에 의하여 국부적인 수축변형을 일으키나, 파단은 2$\frac{1}{4}$Cr-1Mo강의 모재에서 발생하였으며, 거시적인 인장성질에는 영향을 미치지 않았다.

• Journal of Welding and Joining
• /
• v.32 no.2
• /
• pp.4-8
• /
• 2014

In this research, GTA overlay welding system is developed for inside of straight pipes in various diameter. It can be applied to oil, ship building and plant industry, especially pipes connected to pressure vessels, for the purpose of cost reduction by cladding inside of pipes with corrosion and heat resistant alloys such as stainless steel or Inconel. Developed system consists of GTA power source, torch, wire feeding system, automatic arc length adjusting device, CCD camera and cooling unit. Two types of pipe inside overlay welding system are developed. One is for maximum 3m pipe length with 3 inch ~ 12 inch pipe outer diameter. Another type can be applied to maximum 12m pipe length with 7 ~ 24 inch OD. Developed system successfully produced inside cladded pipe and the results are shown through cross sectional images of the pipes.