• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.483-488
• /
• 2001

In the present study a numerical simulation is performed on a natural convection inside a square cavity with a vibrating wall. The study has been conducted varying the heat transfer rate, wall excitation frequency and also the orientation of the cavity. The temperature and velocities inside the cavity was observed and also, the heat transfer coefficients on the heating wall was seen. From the results, it can be seen that the temperature inside the cavity decreases when excited with the proper frequency and the heat transfer coefficient increased with cavity inclination angle, ${\theta}$. It is also found from the results that flow resonance is occurred near the inclination angle ${\theta}=90^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.2
• /
• pp.278-284
• /
• 2001

In this paper, the slanted metallic boundaries is analyzed for the triangular cell grid method and compared with staircase approximation. Specially, this paper is derived an error range to the angle of inclination between the metal and the dielectric from the triangular cell grid method. That result, when the angle of inclination is from 30˚ to 60˚, the triangular cell grid method improves the accuracy, the computer memory and time requirement in comparison with the staircase approximation. But, out of this range, we do not expect the accuracy because a side of cell size lengthen.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.9
• /
• pp.82-88
• /
• 1999

The object of this study is to find new evaluation index for in-cylinder flow chracteristics istead of current swirl, tumble coefficient using steady flow test rig on intake port system. To this end, port flow system. To this end, port flow rig test was conducted on DOHC head varying intake valve lift respectively. Finally combination angular coefficient and inclination angle were introduced as new evaluation index for in-cylinder angularflow characteristics instead of swirl and tumble coefficient.

• The Journal of the Korean dental association
• /
• v.19 no.1 s.140
• /
• pp.67-71
• /
• 1981

This study was undertaken to find out the characteristic craniofacial morphology of Class II Division 2 malocclusions in children by means of roentgenocephalometry. The subjects consisted of twelve boys and thirteen girls with Class Ii, Division 2, thirty seven boys and fifty three girls with Class II, Division 1, and forty six boys and eighty one girls with normal occlusion, ranged from 10 years old to 18 years old. The following results were obtained; 1. The anteroposterior relationship of the maxilla to the cranium in the Class II, Division 2 malocclusion similar to the normal occlusion, but the mandible was the posterior position in th the cranial anatomy. 2. There were no significant differences in the anteroposterior relationship of the maxilla and the mandible between Class II, Division 1 and Class II, Division 2 malocclusions. 3. In Class II, Division 1 the axes of maxillary incisors showed labial inclination, but lingual inclination in Class II, Division 2 malocclusions. 4. Overbite was prominent one in Class II, Division 2, on the other hand overjet was distinguished in Class II, Division 1.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.105-110
• /
• 2004

This paper deals with the study of feasibility of rotary carbide tools in the machining of aluminium alloy. A rotary tool holder was designed and manufactured for this work. Experiments were performed using Taguchi methods and regression analysis to analyse the influence of various factors and their interactions on the cutting characteristics of rotary carbide tools during machining. The cutting force is influenced the most featly at the inclination angle. The surface roughness is influenced distinctly at depth of cut. It deduced an equation to predict cutting force and surface roughness. Hence, it could be concluded here that the proposed model agrees with the experimental data satisfactorily.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1253-1256
• /
• 2005

An Experiment was carried out to study burr minimization in drilling on the inclined exit surface. Several different drills, exit surface angles and cutting conditions were selected to determine their influences on burr formation. In drilling operation, there are not only flat exit surfaces but also inclined exit surfaces which is described as inclination angle. Inclination of exit surface causes a quiet different burr formation when comparing with flat surface. Burr formation mechanisms are analyzed according to the drill geometries and cutting conditions. Several schemes for burr minimization on inclined exit surface were proposed. Burr geometry in each drill and cutting condition are measured by laser measurement system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.3
• /
• pp.53-59
• /
• 2011

In this study, a two-phase closed loop cooling system is desinged and tested for a laptop computer using a FC-72. The cooling system is characterized by a parametric study which determines the effects of existence of a boiling enhancement microstructure, initial system pressure, volume fill ratio of coolant and inclination angle of condenser on the thermal performance of the closed loop. Experimental data show the optium condition when the volume ratio of working fluid is 70%, the pump flowing is 6ml/min, and the inclination angle of condenser is $0^{\circ}$. This research shows the maximum values which can dissipate 33W of chip power with a chip temperature maintained at $95^{\circ}C$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.4
• /
• pp.14-20
• /
• 2005

This paper deals with the study of feasibility of rotary carbide tools in the machining of aluminium alloy. A rotary tool holder was designed and manufactured for this work. Experiments were performed using Taguchi methods and regression analysis to analyse the influence of various factors and their interactions on the cutting characteristics of rotary carbide tools during machining. The cutting force is influenced the most greatly at the inclination angle. The surface roughness is influenced distinctly at depth of cut. It deduced an equation to predict cutting force and surface roughness. Hence, it could be concluded here that the proposed model agrees with the experimental data satisfactorily.

• Advances in Computational Design
• /
• v.5 no.3
• /
• pp.261-276
• /
• 2020

The reasonable layout of vacuum cleaner can effectively improve the collection efficiency of iron filings generated in the process of steel production. Therefore, in this study, the CFD-DEM coupling model and two-fluid model are used to calculate the iron filings collection efficiency of vacuum cleaner with different inclination/cross-sectional area, pressure drop and inlet angle. The results are as follows: The CFD-DEM coupling method can truly reflect the motion mode of iron filings in pneumatic conveying. Considering the instability and the decline of the growth rate of iron filings collection efficiency caused by high pressure drop, the layout of 75° inclination is suggested, and the optimal pressure drop is 100Pa. The optimal simulation results based on two-fluid model show that when the inlet angle and pressure drop are in the range of 45°~65° and 70Pa~100Pa, larger mass flow rate of iron filings can be obtained. It is hoped that the simulation results can offer some suggestion to the layout of vacuum cleaner in the rolling mill.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.42-44
• /
• 2002

This paper presents a utility interactive photovoltaic generation system with the angle of inclination and direction. This paper summarizes the results of these efforts by offering a snapshot of the configuration of photovoltaic in residential applications. The status of PV system components and inter-connection and safety equipment will be summarized. also, 1'his System is able to variation the angle of inclination and direction. Hence this paper discuss only results that might be useful for generation power