• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.156.2-156.2
• /
• 2011

본 연구에서는 일단 수성가스전이반응 (Single stage water gas shift reaction)을 위해 높은 활성을 가진 백금 담지 촉매를 함침법 (Incipient wetness impregnation method)으로 제조하여 높은 공간 속도 (Gas hourly space velocity) $45,515h^{-1}$에서 담체에 따른 촉매 활성을 평가하였다. 담체는 $CeO_2$, $ZrO_2$, MgO, MgO-$Al_2O_3$ (MgO = 30 wt%) 그리고 $Al_2O_3$를 사용하였으며 백금의 담지량은 1 wt%로 고정하였다. BET, XRD, TPR, CO-chemisorption 분석을 통하여 담체의 구조적 특성이 촉매 활성에 미치는 영향에 대하여 조사하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.230.1-230.1
• /
• 2010

조촉매(Promotor)인 Na은 수성가스전이(Water Gas Shift, WGS) 반응 시 생성된 포름산염의 C-H결합을 쉽게 분해하는 역할을 한다. 본 연구에서는 $Pt/CeO_2$ 촉매의 성능 향상을 위해 Na의 담지량을 변화시켜 촉매적 활성을 비교하여 보았다. 제조된 담체는 침전법(Precipitation)을 사용하여 제조하였으며 $500^{\circ}C$에서 6시간 소성하였다. Pt 담지량은 1wt%로 고정하였고 Na 담지량은 1 wt%~5 wt%로 변화를 주어 동시(공)-함침법(Co-incipient wetness method)으로 담지 시켰다. 반응 실험은 공간속도(Gas Hourly Space Velocity, GHSV) $45,385h^{-1}$에서 수행하였다. WGS 반응 결과 3 wt%의 Na이 담지된 $Pt/CeO_2$ 촉매의 경우를 제외하고 나머지 Na이 담지된 촉매들은 비교적 높은 CO의 전환율을 나타내었다. 특히 2 wt%의 Na이 담지된 $Pt/CeO_2$ 촉매는 가장 높은 CO의 전환율을 나타내었다. 따라서 Na 담지량의 변화가 포름산염의 C-H결합 분해에 영향을 미친다는 것을 알 수 있다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.243.2-243.2
• /
• 2010

현재 바이오디젤(Bio diesel)은 유지와 메탄올을 염기촉매를 넣고 전이에스테르화(Trans-esterification)반응하여 생산한다. 생산된 1세대 바이오 디젤은 분자 내 산소가 다량 함유되어 여러 가지 단점을 가지기 때문에 전이에스테르화 반응을 대체한 탈산소(Deoxygenation)반응이 주목 받고 있다. 본 연구에서는 유리지방산(Free fatty acid, FFA)인 올레익 산(Oleic acid)의 탈산소반응을 수행하였다. 하이드로탈사이트(Hydrotalcites) 구조인 MgO-$Al_2O_3$(MgO=70 wt%)를 6시간 동안 $500^{\circ}C$에서 예비소성(Pre-calcination)하여 담체로 사용하였다. 제조된 MgO-$Al_2O_3$ 담체에 함침법(Incipient wetness method)으로 20 wt% Ni을 담지 시켰다. 제조된 Ni/MgO-$Al_2O_3$촉매는 소성온도를 변화시켜 반응 실험을 수행하였다. TPR 분석을 통해 산화-환원특성을 분석하였고 생성물의 원소분석을 통해 생성물의 산소함량을 측정하였다.

• International Journal of Safety
• /
• v.1 no.1
• /
• pp.58-61
• /
• 2002

A preparation method of cobalt supported alumina catalyst for a emergency escape mask cartridge has been studied. Catalysts were prepared by incipient wetness impregnation method using pre-shaped $\gamma$=alumina powders of 70-100 mesh. The catalyst was tested in a continuous-flow reactor system and characterized by elemental analysis, BET and TGA-DTA techniques. Cobalt shows higher activity than platinum or nickel for carbon monoxide oxidation at room temperature. Optimum loading amount of cobalt was 10 wt.% for CO oxidation and the reaction activity increases gradually with the increase of calcination temperature up to $450^{\circ}C.

• Bulletin of the Korean Chemical Society
• /
• v.29 no.2
• /
• pp.328-334
• /
• 2008

The effects of catalyst preparation on the reaction route and the mechanism of biphenol (BP) hydrogenation, which consists of a long series-reaction, were studied. Pd/C catalysts were prepared by incipient wetness method and precipitation and deposition method. The reaction behaviors of the prepared catalysts and a commercial catalyst along with the final product distributions were very different. The choice of the catalyst preparation conditions during precipitation and deposition including the temperature, pH, precursor addition rate, and reducing agent also had significant effects. The reaction behaviors of the catalysts were interpreted in terms of catalyst particle size, metal distribution, and support acidities.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.6
• /
• pp.715-719
• /
• 1999

The incorporation of cobalt into mesoporous molecular sieves MCM-41 and MCM-48 was carried out. Co-PO/MCM41 and Co-PO/MCM48 were prepared using Co(II) acetate solution adjusted to pH = 3.0 with phosphoric acid by the incipient wetness method. Photoacoustic spectroscopy (PAS) was used to study the local environments of Co(II) incorporated into mesopores. The band around 500 nm in PAS of as-prepared Co-PO/MCM41 and Co-PO/MCM48 with Co(II) acetate solution was changed to triplet bands around 600 nm. This could be assigned to the 4 A2(F)-> 4T1(P) transition of Co(II) surrounded tetrahedrally by oxygen ions after calcination. It may be attributable to that the octahedral cobalt species containing phosphate ligands in coordination sphere reacting with framework's silanol groups to be dispersed atomically onto the surface of mesoporous molecular sieves as a tetrahedral species. This is unlike that the Co in Co-Cl/MCM41 and direct-synthesized Co-MCM41 transforms to Co oxide phase upon calcination. Co-PO/MCM41 and Co-PO/MCM48 were stable while treated with water.

• New & Renewable Energy
• /
• v.4 no.4
• /
• pp.80-87
• /
• 2008

Steam reforming of LPG was investigated over spc-Ni/MgAl catalyst in a temperature range of $600{\sim}850^{\circ}C$, feed molar ratio of $H_2O/C=1.0{\sim}3.0$, space velocity of $10,000{\sim}90,000h^{-1}$ and at atmospheric pressure. spc-Ni/MgAl catalyst was prepared by a co-precipitation method, whereas Ni/MgO and $Ni/Al_2O_3$ catalysts were prepared by an incipient wetness method. The characteristics of catalysts were analyzed by N2 Physisorption, CO chemisorption, XRD, TOF-SIMS, SEM and TEM techniques. The Ni/MgO and $Ni/Al_2O_3$ catalysts were deactivated by the formation of carbon. However, the spc-Ni/MgAl catalyst showed higher conversion and $H_2$ selectivity than the other catalysts, even though carbon was formed on the surface of the catalyst during the reaction under the tested reaction conditions.

• International Journal of Advanced Culture Technology
• /
• v.3 no.2
• /
• pp.110-117
• /
• 2015

10 wt% (Ni-Co) catalysts with different Ni and Co content : 10%Ni, 9%Ni1%Co, 7%Ni3%Co, 5%Ni5%Co, 3%Ni7%Co, and 10%Co; were prepared using sol-gel method followed by incipient wetness impregnation method. To investigate the catalytic activity including the stability, dry methane reforming were demonstrated over the pelletized catalysts at $620^{\circ}C$ under atmospheric pressure in a $CH_4:CO_2:N_2$ feedstock for 360 min. The results showed that bimetallic catalysts with the Co content equal to or greater than 3% were more stable than monometallic catalysts (10%Ni and 10%Co). The temperature programmed hydrogenation interpreted that the additional of Co into Ni catalyst improved the carbon resistance from methane cracking. Promoted this type of bimetallic catalyst using 1wt% K (trimetallic catalyst) prevented the carbon formation on the catalyst. The temperature programmed desorption of $CO_2$ indicated that this trimetallic catalyst has a greater number of strong basic sites. Moreover, the appearance of K lowered the number of weak basic sites and decreased the conversion of methane by 12 %.

• Journal of the Korean Society of Combustion
• /
• v.10 no.1
• /
• pp.20-26
• /
• 2005

In the present study, catalytic combustion of hydrogen-air premixture in a millimeter scale monolith coated with Pt catalyst was investigated. As the combustor size decreases, the heat loss increases in proportion with the inverse of the scale of combustion chamber and combustion efficiency decreases in a conventional type of combustor. Combustion reaction assisted by catalyst can reduce the heat loss by decreasing the reaction temperature at which catalytic conversion takes place. Another advantage of catalytic combustion is that ignition is not required. Platinum was coated by incipient wetness method on a millimeter scale monolith with cell size of $1{\times}1mm$. Using this monolith as the core of the reaction chamber, temperatures were recorded at various locations along the flow direction. Burnt gas was passed to a gas chromatography system to measure the hydrogen content after the reaction. The measurements were made at various volume flow rate of the fuel-air premixture. The gas chromatography results showed the reaction was complete at all the test conditions and the reacting species penetrated the laminar boundary layer at the honeycomb and made contact with the catalyst coated surface. At all the measuring locations, the record showed monotonous increase of temperature during the measurement duration. And the temperature profile showed that the peak temperature is reached at the point nearest to the gas inlet and decreasing temperature along the flow direction.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.203-206
• /
• 2009

Agglomeration of catalysts is known as one of the major degradation mechanisms. Reforming of liquid fuel, which requires high temperature over $800^{\circ}C$, accelerates agglomeration of catalysts. In this work, The effects of agglomeration on catalysts activity in partial oxidation reforming conditions were investigated. Metal supported catalysts(Pt-CGO, Ru-CGO) were compared to perovskite-structured catalysts(NECS-P1, NECS-P2). High thermal stability of perovskite-structured catalysts was reported. Micro-reactor installed in electric furnace was used. its Temperature was raised from $800^{\circ}C$ to $1000^{\circ}C$ to accelerate agglomeration effect. To measure rate of agglomeration, BET analysis and CO pulse chemisorption were conducted on catalysts exposed to $1100^{\circ}C$. Metal supported catalysts showed degradation at $1000^{\circ}C$ and The rates were different according to metal supported. On the other hand perovskite-structured catalysts showed no degradation at $1000^{\circ}C$.