• Structural Engineering and Mechanics
• /
• v.39 no.2
• /
• pp.207-221
• /
• 2011

This paper aims to study the behavior of short reinforced concrete columns confined with external glass Fiber Reinforced Polymers (GFRP) sheets under eccentric loads. The experimental part of the study was achieved by testing 9 specimens under eccentric compression. Three eccentricity ratios corresponding to e/t = 0, 0.10, 0.50 in one direction of the column were used. Specimens were divided into three groups. The first group was the control one without confinement. The second group was fully wrapped with GFRP laminates before loading. The third group was wrapped under loading after reaching 75% of failure loads of the control specimens. The third group was investigated in order to represent the practical case of strengthening a loaded column with FRP laminates. All specimens were loaded until failure. The results show that GFRP laminates enhances both failure load and ductility response of eccentrically loaded column. Moreover, the study also illustrates the effect of confinement on the first crack load, lateral deformation, strain in reinforcement and failure pattern. Based on the analysis of the experimental results, a simple model has been proposed to predict the improvement of load carrying capacity under different eccentricity ratios. The predicted equation takes into consideration the eccentricity to cross section depth ratio, the ultimate strength of GFRP, the thickness of wrapping laminate, and the time of wrapping (before loading and under loading). A good correlation was obtained between experimental and analytical results.

• The Journal of the Korea Contents Association
• /
• v.21 no.3
• /
• pp.602-608
• /
• 2021

For the comparison of bond strength between the Co-Cr alloy and ceramic, which are clinically used, test samples made with a traditional casting method as a control group), and Milling and SLM(3d printing group) samples were made as an experimental group. The metal-ceramic bond strength was measured with a universal testing machine. For the measurement, a three-point bending test was conducted. After the bond strength was measured, metal-ceramic interface was observed. According to the test result, casting group had 53.59 MPa, milling group had 45.90 MPa, and 3d printing group had 58.34 MPa. There was no statistical significance. With regard to failure pattern, most of the samples in two groups, showed mixed failure. This study showed a clinically applicable value when measuring the bond strength of alloy-ceramic material with an alloy produced by 3D printing.

• Journal of Dental Anesthesia and Pain Medicine
• /
• v.15 no.3
• /
• pp.113-119
• /
• 2015

Background: The inferior alveolar nerve block (IANB) is the most common anesthetic techniques in dentistry; however, its success rate is low. The purpose of this study was to determine the correlation between IANB failure and mandibular skeletal characteristics Methods: In total, 693 cases of lower third molar extraction (n = 575 patients) were examined in this study. The ratio of the condylar and coronoid distances from the mandibular foramen (condyle-coronoid ratio [CC ratio]) was calculated, and the mandibular skeleton was then classified as normal, retrognathic, or prognathic. The correlation between IANB failure and sex, treatment side, and the CC ratio was assessed. Results: The IANB failure rates for normal, retrognathic, and prognathic mandibles were 7.3%, 14.5%, and 9.5%, respectively, and the failure rate was highest among those with a CC ratio < 0.8 (severe retrognathic mandible). The failure rate was significantly higher in the retrognathic group than in normal group (P = 0.019), and there was no statistically significant difference between the other two groups. Conclusions: IANB failure could be attributable, in part, to the skeletal characteristics of the mandible. In addition, the failure rate was found to be significantly higher in the retrognathic group.

• Journal of Sasang Constitutional Medicine
• /
• v.17 no.3
• /
• pp.103-112
• /
• 2005

1. Objective : The present author have examined the comparative effects of Hyeongbangjihwang-tang and Sibimikwanjung-tang in glycerol-induced acute renal failure, a model for myoglobinuric acute renal failure. 2. Methods : Above two prescriptions were applied to rat ad libitum and serum level of creatinine, glucose and blood urea nitrogen(BUN) were measured. And serum level of $Na^+$, $K^+$ and $Cl^-$, too. 50%(vol/vol) glycerol at a dose of 10 ml/kg of rat body weight intramuscularly and 1% concentration of prescriptions were applied to rats for 7 days ad libitum. 3. Results : Serum level of creatinine and $K^+$ significantly increased by glycerol injection, and these showed pre-renal and renal cause of acute renal failure. Hyeongbangjihwang-tang administered group showed decreasing tendency on serum level of creatinine when compared with control groups, but not significant. Sibimikwanjung-tang administered group showed significant increase of serum level of BUN when compared with control groups. 4. Conclusions : Above two prescriptions showed no significant changes on glycerol induced acute renal failure, but Hyeongbangjihwang-tang and Sibimikwanjung-tang showed a little different manner of response.

• Restorative Dentistry and Endodontics
• /
• v.20 no.1
• /
• pp.97-112
• /
• 1995

The purpose of this study was to evaluate the effect of wetting condition made by drying time on bonding of resin cement to dentin. Freshly extracted bovine teeth were grinded to expose flat dentin surfaces. After the exposed dentin surfaces were treated with pretreatment agents and water rinse, each wetting condition of dentin surfaces was made according to drying times and methods including slight blow bry for I-second by air syringe, blow dry for 20-second by air syringe, and 12-hour dry in desiccator respectively. and then, previously made composite resin specimens were bonded onto each conditioned dentin surface of the specimen using Panavia-21(Kuraray Co.), Bistite(Tokuso Co.), and Choice(use with All bond-2, Bisco Inc.) resin cement according as manufacturer's instruction. Bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, then the tensile bond strength was measured, cohesive failure rate was calculated, and fractured dentin surfaces and acrylic rod sides were examined under scanning electron microscope. The result were as follows ; In the group of bonding with Panavia-21 resin cement, higher tensile bond strength was seen in 12-hour dry group than in I-second and 20-second dry group(p<0.01). In the group of bonding with Bistite resin cement, higher tensile bond strength was seen in 1-second dry group than in 20-second and 12-hour dry group(p<0.01). In the group of bonding with Choice resin cement, no significant differences of bond strength under given drying time were seen. Cohesive failure rates derived from the groups of bonding with Panavia-21 and Choice resin cement were increased with the increase of tensile bond strength in each drying time. On SEM examination of fractured surface, adhesive failure mode with fractured resin tags was mostly seen in wet condition with I-second drying time in the group of bonding with Panavia-21 resin cement, mixed failure mode with shortened and fractured resin tag was seen in the group of bonding with Bistite resin cement, and regardless of drying time, and cohesive-adhesive mixed failure mode with fracture of 'Hollow' typed resin tags was mainly seen in the group of bonding with Choice resin cement.

• Journal of Gastric Cancer
• /
• v.15 no.4
• /
• pp.246-255
• /
• 2015

Purpose: The importance of Helicobacter pylori eradication after endoscopic resection (ER) of gastric neoplasms remains controversial. In this study, we clarified the importance of H. pylori eradication for metachronous lesions after ER. Materials and Methods: This study included 3,882 patients with gastric neoplasms who underwent ER. We included patients infected with H. pylori who received eradication therapy. Among them, 34 patients with metachronous lesions after ER and 102 age- and sex-matched patients (nonmetachronous group) were enrolled. Background mucosal pathologies such as atrophy and intestinal metaplasia (IM) were evaluated endoscopically. The expression levels of CDX1, CDX2, Sonic hedgehog (SHH), and SOX2 were evaluated based on H. pylori eradication and the development of metachronous lesions. Results: The eradication failure rate was higher in the metachronous group than in the nonmetachronous group (P=0.036). Open-type atrophy (P=0.003) and moderate-to-severe IM (P=0.001) occurred more frequently in the metachronous group. In patients with an initial diagnosis of dysplasia, the eradication failure rate was higher in the metachronous group than in the nonmetachronous group (P=0.002). In addition, open-type atrophy was more frequent in the metachronous group (P=0.047). In patients with an initial diagnosis of carcinoma, moderate-to-severe IM occurred more frequently in the metachronous group (P=0.003); however, the eradication failure rate was not significantly different between the two groups. SHH and SOX2 expression was increased, and CDX2 expression was decreased in the nonmetachronous group after eradication (P<0.05). Conclusions: Open-type atrophy, moderate-to-severe IM, and H. pylori eradication failure were significantly associated with metachronous lesions. However, eradication failure was significantly associated with dysplasia, but not carcinoma, in the metachronous group. Thus, H. pylori eradication may play an important role in preventing metachronous lesions after ER for precancerous lesions before carcinomatous transformation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.2
• /
• pp.157-170
• /
• 2001

The bond strength is the most important factor in establishing long-term success of resin-retained fixed prostheses. So, various surface treatment methods have been introduced to improve the bond strength of metal surface and bonding resin till now This study was performed to compare the effect of silicoating with that of metal primer and analyze the correlation between treatment time of sandblasting and the bond strength, so that meant to find more effective surface treatment method that could enhance the bond strength of resin-retained fixed prostheses. The surfaces of all specimens made of $Verabond^{(R)}$ alloys were air abraded with $250{\mu}m\;Al_2O_3$ according to treatment time of sandblasting and they were subdivided to be treated with only sandblasting(S group), silicoating following sandblasting(SS group) and metal primer application after sandblasting(SM group). Then pairs of metal specimens (${\phi}10mm{\times}h\;2mm,\;{\phi}6{\times}h\;2mm$) were bonded with Super bond $C&B^{(R)}$. The specimens were stored in $38^{\circ}C$ water for 48 hours and shear bond strength was measured using the universal testing machine. The results were as follows, 1. In the comparison of shear bond strength according to treatment time of sandblasting, bond strength was increased in the order of 0', 15', 30', 45', 60' group. 0' group had significantly lower value than any other, while 0', 15' group were significantly different with 30', 45', 60' group(p<0.05). 2. In the comparison of shear bond strength according surface treatment methods, bond strength was increased in the order of S group. SS group and SM group. S group was significantly different with SS group and SM group(p<0.05). 3. Observing the mode of bond failure. 0', 15' group showed only adhesive failure, and 30', 45', 60' group did mostly adhesive & cohesive failure in S group. In SS group and SM group, all other groups except 0', 15' group showed mostly cohesive failure. From the above results, it is considered that sandblasting should be treated for more than 30 seconds, and metal primer be more effective and available clinically than silicoater system which is complicate, technique-sensitive and time-consuming method, when nonprecious metal surface is planning be treated with in order enhance the bond strength of resin-retained fixed prostheses.

• Archives of Pharmacal Research
• /
• v.28 no.4
• /
• pp.483-487
• /
• 2005

The aim of this study was to investigate the pharmacokinetic changes of verapamil and its major metabolite, norverapamil, after oral administration of verapamil (10 mg/kg) in rabbits with slight, moderate and severe hepatic failure induced by carbon tetrachloride. The plasma verapamil concentrations in all groups of hepatic failure were significantly higher (p<0.01) than the control. However, the plasma norverapamil concentrations in severe hepatic failure were significantly higher (p<0.05) than the control. The peak concentrations ($C_{max}$) and the areas under the plasma concentration-time curve (AUC) of verapamil in the rabbits were significantly (p<0.01) higher than the control. The absolute bioavailability ($F_{A.B}$) and the relative bioavailability ($F_{R.B}$) of verapamil in the rabbits with hepatic failure were significantly higher ($13.6-22.2\% and 150-244\%$, respectively) than the control ($9.1\% and 100\%$, respectively). Although the AUC and $C_{max}$ of its major metabolite, norverapamil, in slight, moderate hepatic failure were not significantly lower than the control, the metabolite-parent AUC ratio in all groups of hepatic failure was decreased significantly (p<0.05, in slight group; p<0.01, in moderate and severe group) than the control. This could be due to decrease in metabolism of verapamil in the liver because of suppressed hepatic function in the hepatic failure groups because verapamil is mainly metabolized in the liver. From our data, it would seem appropriate that in patients with liver disease, doses of verapamil should be decreased by degree of hepatic failure.

• The korean journal of orthodontics
• /
• v.43 no.4
• /
• pp.186-192
• /
• 2013

Objective: To analyze the fatigue resistance, debonding force, and failure type of fiber-reinforced composite, polyethylene ribbon-reinforced, and braided stainless steel wire lingual retainers in vitro. Methods: Roots of human mandibular central incisors were covered with silicone, mimicking the periodontal ligament, and embedded in polymethylmethacrylate. The specimens (N = 50), with two teeth each, were randomly divided into five groups (n = 10/group) according to the retainer materials: (1) Interlig (E-glass), (2) everStick Ortho (E-glass), (3) DentaPreg Splint (S2-glass), (4) Ribbond (polyethylene), and (5) Quad Cat wire (stainless steel). After the recommended adhesive procedures, the retainers were bonded to the teeth by using flowable composite resin (Tetric Flow). The teeth were subjected to 10,00,000 cyclic loads (8 Hz, 3 - 100 N, $45^{\circ}$ angle, under $37{\pm}3^{\circ}C$ water) at their incisoproximal contact, and debonding forces were measured with a universal testing machine (1 mm/min crosshead speed). Failure sites were examined under a stereomicroscope (${\times}40$ magnification). Data were analyzed by one-way analysis of variance. Results: All the specimens survived the cyclic loading. Their mean debonding forces were not significantly different (p > 0.05). The DentaPreg Splint group (80%) showed the highest incidence of complete adhesive debonding, followed by the Interlig group (60%). The everStick Ortho group (80%) presented predominantly partial adhesive debonding. The Quad Cat wire group (50%) presented overlying composite detachment. Conclusions: Cyclic loading did not cause debonding. The retainers presented similar debonding forces but different failure types. Braided stainless steel wire retainers presented the most repairable failure type.

• Advances in pediatric surgery
• /
• v.6 no.1
• /
• pp.10-18
• /
• 2000

Multisystem organ failure resulting from gram negative bacterial sepsis is associated with high morbidity and mortality in surgical neonates. There are differences in the clinical characteristics of organ failure in neonates and adults. The purpose of this study is to identify the differences and determine the order of organ failure between baby rats and adult rats after induction of gram negative sepsis. Fifty baby rats less than 30-day-old and another 50 adult rats more than 2-month-old were divided into control group (G1) and experimental group (G2). The G1 consisted of 10 baby- and 10 adult-rats, and the G2 consisted of 40 babies and 40 adults. E. coli ($10^8/mL$ per 100g of body weight) were injected into the peritoneal cavity in G2 and same amount of saline was injected in G 1. Blood samples were obtained before injection, 24 hour, 48 hour, 72 hour and after death. WEC, platelet, $PaO_2$, $PaCO_2$, total bilirubin, BUN, creatinine, albumin and abdominal wall thickness were measured to evaluate the sequence of organ failure. The mortality was 55.0 % in G2-babies and 32.5 % in G2-adults. In baby rats, microvascular, hematologic and renal failure appeared within 24 hours after injection and pulmonary failure followed. Pulmonary, renal and liver failure developed within 24-48 hours in adult rats; however, microvascular failure did not appear until they were moribund. Thrombocytopenia, hypoalbuminemia, increased BUN and generalized edema was the earlist sign of sepsis in baby rats.