• 한국항공운항학회지
• /
• 제14권4호
• /
• pp.1-10
• /
• 2006

A computational study was carried out in order to investigate the ground effect of a circular cylinder in the presence of a moving wall at a Reynolds number of 2.0${\times}$104. The viscous-incompressible Navier-Stokes equations and Spalart-Allmaras turbulent model of the commercial CFD code were adopted for this numerical analysis. The moving wall was set parallel with the freestream, and the speed of motion was equal to the freestream velocity. The gap ratio is defined as the distance ratio between the circular cylinder diameter and the height from the moving wall. The numerical results show that there are the differences among the each of the stages in evidence of the vorticity contours and the polar diagrams of $C_l$ vs. $C_d$. The 4 stages of the gap ratio are defined according to the flow features, whose stages are divided into small, intermediate, large and convergence gap ratios, respectively.

• 한국군사과학기술학회지
• /
• 제26권2호
• /
• pp.159-170
• /
• 2023

In the present study, the dynamic behavior characteristics of an amphibious assault vehicle during water entry were analyzed using STAR-CCM+, a commercial computational fluid dynamics(CFD) code. All computations were performed using an overset mesh system and a RANS based flow-solver coupled with dynamic fluid-body interaction(DFBI) solver for simulating three degrees of freedom motion. For numerical validation of the solver, a water entry simulation of inclined circular cylinder was conducted and it was compared between an existing experiment data and CFD results. The pitch angle variation and the trajectory of the circular cylinder during water entry shows good agreement with previous experimental and numerical studies. For the water entry simulations of the amphibious assault vehicle, the analysis of dynamic behaviors of the amphibious assault vehicle with different slope angles, submerged depths and initial velocities were conducted. It is confirmed that the steep slope angle increases the submerged volume of the amphibious assault vehicle, so the buoyancy acting on the vehicle is increased and the moved distance for the re-flotation is decreased. It is also revealed that the submerged volume is increased, bow-up phenomenon occur earlier.

• 대한기계학회논문집A
• /
• 제41권11호
• /
• pp.1077-1084
• /
• 2017

기존의 선박용 디젤 엔진에는 항상 일정한 엔진 부하량을 유지하는 캠 구동장치가 적용되고 있었으나, 최근 환경규제로 인하여 엔진 부하량에 따라 실린더 온도를 개별적으로 제어하는 LDCL(Load dependent cylinder liner) JWCS(Jacket water cooling system)가 적용된 전자유압 제어방식이 개발되었다. 이 시스템에서 3-way 밸브는 실린더의 상부와 하부와의 온도 차이를 줄여 저온부식을 방지하는데, 대부분 수입에 의존하고 있으며 토출유량이 낮다. 이에 본 연구에서는 3-way 밸브 내부 형상 관련 설계인자가 성능(토출 유량 및 온도)에 미치는 영향을 파악하여 밸브의 형상 설계를 수행하였으며, 기존 모델과의 성능 비교를 통해 제안된 밸브의 우수성을 검증하였다.

• 한국음향학회지
• /
• 제37권4호
• /
• pp.163-173
• /
• 2018

본 논문에서는 비행 중 비행체 표면에 작용하는 음향하중 예측을 수행하였다. 비행 중 음향하중은 비행체 표면의 압력 변동에 의해 발생한다. 기존의 비행 중 음향하중 예측방법은 반경험적 방법으로 이론과 실험 결과를 기반으로 도출한 경험식을 활용한다. 하지만 경험식의 입력 값으로 사용되는 비행체 주변 유동특성 및 경계층 파라미터를 매번 실험을 통해 얻는 것에는 한계가 있다. 따라서 본 논문에서는 전산유체해석(Computational Fluid Dynamics, CFD) 결과를 반경험적 방법과 혼합하는 하이브리드 방법을 이용하여 비행 중 비행체에 작용하는 음향하중을 예측하였다. Cone-cylinder-flare 형상 비행체에 대해 아음속, 천음속, 초음속, 최대동압도달(Maximum dynamic pressure, Max-q) 시점의 비행 환경에 대한 음향하중 예측을 수행하였다. 하이브리드 방법 적용 시 전산유체해석결과를 기반으로 한 경계층 끝단 영역 판단 방법에 대해 비교하였고 여러 연구자에 의해 제시된 경험식에 따른 음향하중 예측결과를 비교하였다.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.64-70
• /
• 2008

Temperatures of engine head and liner depend on many factors such as spray and combustion process, coolant passage flow and engine related structures. To estimate the temperature distribution of engine structure, multi-dimensional computational fluid dynamics (CFD) codes have been mainly adopted. In this case, it is of great importance to obtain the realistic wall temperature distribution of entire engine structure. In the present work, a CFD-FEM coupling methodology was presented to address this demand. This approach was applied to a real large-size marine diesel engine. CFD combustion and coolant flow simulations were coupled to FEM temperature analysis. Wall heat flux and wall temperature data were interfaced between combustion simulation and solid component temperature analysis via translator by a commercial CFD package named FIRE by AVL. Heat transfer coefficient and surface temperature data were exchanged and mapped between coolant flow simulation and FEM temperature analysis. Results indicate that there exists the optimum cell thickness near combustion chamber wall to reasonably predict the wall heat flux during combustion period. The present study also shows that the effect of cell refining on predicting in-cylinder pressure during combustion is negligible. Hence, the basic guidance on obtaining the wall heat flux needed for the reasonable CFD-FEM coupling analysis has been established. It is expected that this coupling methodology is a robust tool for practical engine design and can be applied to further assessment of the temperature distribution of other engine components.

• 한국전산유체공학회지
• /
• 제18권2호
• /
• pp.49-55
• /
• 2013

The goal of the research is to evaluate the open source code of OpenFOAM for the use of nuclear plant flow simulation objectively. Of the various incompressible flow solvers, simpleFoam, pimpelFoam are then tested under three validated cases (backward facing step, flow over circular cylinder and turbulent round jet flow). For the evaluation of steady state incompressible laminar flow simulation, low reynolds number of backward facing step flow was solved by simpleFoam. The resultant of the reattached lengths turned out to be similar with the other experimental and simulation results. For transient flow simulation, flow over circular cylinder and turbulent round jet flow were solved by pimpleFoam. The simulation accuracy was evaluated by comparing the resultant flow patterns with the description of the characteristics of the flow over the circular cylinder. The quantitative accuracy was evaluated for no more than 85% by comparing it to the decaying constants of the turbulent round jet velocity.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제25회 KOSCI SYMPOSIUM 논문집
• /
• pp.215-222
• /
• 2002

It has been well acknowledged that intake system plays great role in the performance of reciprocating engine. Well-designed intake system is expected to not only increase engine efficiency but also decrease engine emission, which is one of the most urgent issues in the automotive society. Thorough understanding of the flow in intake system helps great to design adequate intake system. Even though both experimental and numerical methods are used to study intake flow, numerical analysis is more widely used due to its merits in time and economy. Intake system of In-line 6-Cylinder CNG engine was chosen for the analysis ICEM CFD HEXA was used to create 3-D structured grid and FIRE code was used for the flow analysis in the intake system. Due to the complexity of the geometry standard ${\kappa}-{\varepsilon}$ turbulence model was applied. Numerical analysis was performed for various inlet and outlet boundary conditions under both steady and transient flow. Inlet mass flow rate and outlet pressure variation were changing parameters with respect to engine speed. Flow parameters, such as velocity, pressure and flow distribution, were evaluated to provide adequate data of this intake system.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.184-189
• /
• 2006

Tumble flow test rig has been used as the useful tool in the developing intake system because major flow pattern induced by intake port of DOHC engine is tumble. Angular momentum of in-cylinder tumble flow can not be directly measured by impulse torque meter in the test rig like that of in-cylinder swirl flow due to rotational axis of the flow. Therefore the adaptor to transform tumble to swirl flow must be adapted in the test rig. In this study, using the commercial CFD code STAR-CD, we studied the effects on measured results due to the variation of the major design variables in the adaptor, tube length(L), tube diameter(D) and cylinder height(H). The effect of the attached angle($\theta$) of the test head to the adaptor also was simulated.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.86-87
• /
• 2011

In this paper, a conjugate heat transfer around cylinder with heat generation was investigated. Both forced convection and conduction was considered in the present finite element simulation. A finite element formulation based on SIMPLE type algorithm was adopted for the solution of the incompressible Navier-Stokes equations. We compared the finite element solution with that of Ansys fluent 12.0, in which finite volume method was employed for spatial discretization. It was found that the finite element method gave more accurate solution than Ansys fluent 12.0. Further, it was found that the maximum temperature inside cylinder is positioned at the rear side due to the flow separation.

• Wind and Structures
• /
• 제34권1호
• /
• pp.1-14
• /
• 2022

In this work the flow through a hollow porous 5:1 rectangular cylinder made of perforated plates is numerically investigated by means of 2D URANS based simulations. Two approaches are adopted to account for the porous surfaces: in the first one the pores are explicitly modeled, so providing a detailed representation of the flow. In the second one, the porous surfaces are modeled by means of pressure jumps, which allow to take into account the presence of pores without reproducing the flow details. Results obtained by using the two aforementioned techniques are compared aiming at evaluating differences and similarities, as well as identifying the main flow features which might cause discrepancies. Results show that, even in the case of pores remarkably smaller than the immersed body, their arrangement can lead to local mechanisms able to affect the global flow arrangement, so limiting the accuracy of pressure jumps based simulations. Despite that, time-averaged fields often show a reasonable agreement between the two approaches.