• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.3017-3029
• /
• 2023

In the late in-vessel phase of a nuclear reactor severe accident, the internal heat transfer and crust evolution during the debris bed melting process have important effects on the thermal load distribution along the vessel wall, and further affect the reactor pressure vessel (RPV) failure mode and the state of melt during leakage. This study coupled the phase change model and large eddy simulation to investigate the variations of the temperature, melt liquid fraction, crust and heat flux distributions during the debris bed melting process in the hypothetical severe accident of HPR1000. The results indicated that the heat flow towards the vessel wall and upper surface were similar at the beginning stage of debris melting, but the upward heat flow increased significantly as the development of the molten pool. The maximum heat flux towards the vessel wall reached 0.4 MW/m². The thickness of lower crust decreased as the debris melting. It was much thicker at the bottom region with the azimuthal angle below 20° and decreased rapidly at the azimuthal angle around 20-50°. The maximum and minimum thicknesses were 2 and 90 mm, respectively. By contrast, the distribution of upper crust was uniform and reached stable state much earlier than the lower crust, with the thickness of about 10 mm. Moreover, the sensitivity analysis of initial condition indicated that as the decrease of time interval from reactor scram to debris bed dried-out, the maximum debris temperature and melt fraction became larger, the lower crust thickness became thinner, but the upper crust had no significant change. The sensitivity analysis of in-vessel retention (IVR) strategies indicated that the passive and active external reactor vessel cooling (ERVC) had little effect on the internal heat transfer and crust evolution. In the case not considering the internal reactor vessel cooling (IRVC), the upper crust was not obvious.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.3
• /
• pp.39-44
• /
• 1994

This study was carried out to investigate features pertaining to spiral thickenings, which was considered one of the most important diagnostic values, for wood identification. Species, kind of cells with spiral thickening, and ridge numbers of spiral thickening per axial mm were recorded in 71 families, 144 genera, 316 species of Korean hardwoods. Spiral thickening was observed in 128 of 316 species, about 40.5 % of all the investigated, and classified into 6 types on the basis of distributional patterns and morphological features as follows: 1. Type 1, present throughout all vessel element, which was found in 14 families, 19 genera, 43 species. 2. Type 2, present only in small vessel element, which was found in 18 families, 29 genera, 41 species. 3. Type 3, present both in small vessel element and wood fibers, which was found in 8 families, 17 genera, 29 species. 4. Type 4, present in wood fibers, which was found in 1 family, 1 genus, 1 species. 5. Type 5, present only in tail of vessel element, which was found in 4 families, 5 genera, 9 species. 6. Type 6, being present in vessel element faintly or partially, which was found in 2 families, 3 genera, 5 species.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.47 no.4
• /
• pp.428-434
• /
• 2011

To establish a vessel safety management system for improving the safety of vessel's traffic and preventing vessel's traffic accidents, the state of marine traffic in the Busan South Port was investigated and analyzed as preliminary survey of the countermeasures. As a result of the study, there are 1,158 vessels in a day, 48 vessels in an hour, and the maximum traffic is about 118 vessels between 16:00 and 17:00 hours everyday, which requires to establish and operate a traffic control system necessarily for ensuring vessel's traffic safety. Furthermore, passages of tanker, passenger ship, cargo vessel and government vessel showed to sail along main traffic lane to be obtained enough sea depth at the survey area. However, passages of fishing vessel and launch showed to sail freely at all survey area owing to outstanding maneuverability and a shallow draft. Some vessels of launch sailed along main traffic lane, but other vessels crossed to sail it. The passages to cross main traffic lane is higher the risk of collision. Therefore, safety measures are urgently needed for the operation of the Busan South Port management system and the prevention of marine pollution.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.1
• /
• pp.98-118
• /
• 2014

An auto weather-vaning system for a Dynamic Positioning (DP) vessel is proposed. When a DP vessel is operating, its position keeping is hindered by ocean environmental disturbances which include the ocean current, wave and wind. Generally, most ocean vessels have a longitudinal length that is larger than the transverse width. The largest load acts on the DP vessel by ocean disturbances, when the disturbances are incoming in the transverse direction. Weather-vaning is the concept of making the heading angle of the DP vessel head toward (or sway from) the disturbance direction. This enables the DP vessel to not only perform marine operations stably and safely, but also to maintain its position with minimum control forces (surge & sway components). To implement auto weather-vaning, a nonlinear controller and a disturbance observer are used. The disturbance observer transforms a real plant to the nominal model without disturbance to enhance the control performance. And the nonlinear controller deals with the kinematic nonlinearity. The auto weather-vaning system is completed by adding a weather-vaning algorithm to disturbance based controller. Numerical simulations of a semi-submersible type vessel were performed for the validation. The results show that the proposed method enables a DP vessel to maintain its position with minimum control force.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.11a
• /
• pp.309-314
• /
• 1996

Feasibility study has been accomplished to evaluate the effectiveness of the in-vessel core debris cooling through lower cavity flooding using two dimensional finite difference scheme. The volume of cerium pool and decay power rate generated in corium pool were evaluated as important parameters to the temperature distribution on the reactor vessel lower head through previous works. In this study, the corium volume based on the System 80＋ core structure and time dependent decay power rate are considered for feasibility evaluation. In addition, preliminary plans for the in-vessel core debris cooling through lower cavity flooding as severe accident management strategy, i.e. flooding timing, method and capacity, are suggested based on the result of the numerical study, international tendency related to in-vessel core debris cooling through lower cavity flooding.

• Journal of Navigation and Port Research
• /
• v.34 no.9
• /
• pp.693-698
• /
• 2010

In port and its approach channel, traffic accidents such as collision, aground, minor collision have reached about 77% of total marine casualty in the area. In this paper, an attempt to enhance the safe navigation was proposed by offering marine traffic supporting system which helps VTS operator assist vessel effectively with the quantitative assessment on difficulty of each vessel. The system collects navigation data from onboard AIS, assesses the data in assessment mode to analyze the navigation difficulties of each vessel and displays the degree of danger of each vessel on the ECDIS in real-time to decide the intervention time or order of priority for VTS operator. The effectiveness of the system was verified by the VTS operators in Korea.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.208-222
• /
• 2021

Managing with the presence of sea ice is the primary challenge in the operation of floating platforms in the Arctic region. It is widely accepted that offshore structures operating in Arctic conditions need station-keeping methods as well as ice management by icebreakers. Dynamic Positioning (DP) is one of the station-keeping methods that can provide mobility and flexibility in marine operations. The presence of sea ice generates complex external forces and moments acting on the vessel, which need to be counteracted by the DP system. In this paper, an icevaning control algorithm is proposed that enables Arctic offshore vessels to perform DP operations. The proposed icevaning control enables each vessel to be oriented toward the direction of the mean environmental force induced by ice drifting so as to improve the operational safety and reduce the overall thruster power consumption by having minimum external disturbances naturally. A mathematical model of an Arctic offshore vessel is summarized for the development of the new icevaning control algorithm. To determine the icevaning action of the Arctic offshore vessel without any measurements and estimation of ice conditions including ice drift, task and null space are defined in the vessel model, and the control law is formulated in the task space. A backstepping technique is utilized to handle the nonlinearity of the Arctic offshore vessel's dynamic model, and the Lyapunov stability theory is applied to guarantee the stability of the proposed icevaning control algorithm. Experiments are conducted in the ice tank of the Korea Research Institute of Ships and Ocean Engineering to demonstrate the feasibility of the proposed approach.

• Plant Journal
• /
• v.8 no.1
• /
• pp.60-72
• /
• 2012

In this study to reduce the review time of the pressure vessel regulations pressure vessel legislation review program has been developed. During the course of this research program to develop the domestic construction in a real project, saving 47% of the time was found.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.1
• /
• pp.15-20
• /
• 1993

X-ray diffractograms of the vessel elements and the wood fibers of Quercus variabilis BLUME were recorded and resolved into characteristic reflections of cellulose I. Some differences were observed in the ratio of integrated intensity and crystallinity index between vessel elements and wood fibers. Present results suggest that cellulose crystal structure in the hardwood species was varied with the elements of wood.

• Nuclear Engineering and Technology
• /
• v.52 no.8
• /
• pp.1650-1660
• /
• 2020

Comparing with the large containment, the gas can not flow freely within the local compartment due to the small volume of the compartment in case of serious accident, which affects the hydrogen flow distribution, and it will determines the location where high concentration occurs in compartment. In this paper, hydrogen distribution and possible hydrogen risk in the vessel under the different conditions are investigated. The results show that when the initial gas momentum is increased, the ability of gas enters into the upper region of the vessel will be strengthened, and the hydrogen volume fraction in the upper region of the vessel is higher. Comparing with horizontal source direction, when source direction is vertically towards upper space, hydrogen is more likely to accumulate in the upper region of the vessel. With the increasing of steam mass flow, the dilution effect of steam on the hydrogen volume fraction will be strengthened, while the pressure in the vessel is also increased. When steam flow is decreased, the hydrogen explosion risk is higher in the vessel. The experiment data can provide technical support for the validation of the CFD software and the mitigation of hydrogen risk in the containment compartment.