• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.717-724
• /
• 2020

We study the closing characteristics of a self-sustainable poppet valve which serves as a main oxidizer shut-off valve for liquid rocket engines. Numerical analysis for predicting closing transient responses are presented and the calculated results have been verified by a comparison with experimental data. The effective area of a pilot gas discharge system and the pressure distribution of passage flow around the valve moving part are shown to be main parameters in determining the closing characteristics for dry and cryogenic conditions, respectively. Moreover, it is presented that the passage flow pressure at the valve closing moment as well as the valve closing velocity can be effectively adjusted by the appropriate employment of the pilot gas.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.1
• /
• pp.47-58
• /
• 2014

In this research, the initial sizing of a HALE(High Altitude Long Endurance) UAV which uses solar power and hydrogen fuel cell as an alternative energy was performed. Instead of a wing box type, a glider type was chosen since it is relatively easy to get a data thanks to many researches abroad. Maximum takeoff weight is around 150Kg and the propulsion system is composed of motor, propeller, solar cell, and hydrogen fuel cell which can be recharged through electrolysis. Maximum takeoff weight was estimated as aspect ratio, wing span, wing area change while considering energy balance of required energy which is necessary for flight during the entire day and available energy which can be taken from the solar cell.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.5
• /
• pp.393-401
• /
• 2018

Reliability prediction of an electronic arm fire device(EAFD) was studied which is applied to prevent accidental ignition in a solid rocket motor. For predicting the reliability, the main components of the EAFD were first defined(Control unit, LEEFI, TBI) and the operating principle of each component was analyzed. Performance modeling of each part is established using selected input variables through system analysis. When complex analysis is required, we approximated it with polynomial equation using response surface method. Monte-Carlo simulation is applied to performance modeling to estimate the design reliability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.10
• /
• pp.801-807
• /
• 2020

Opening characteristics of a main oxidizer shut-off valve at different valve inlet pressures have been experimentally investigated. The pilot pressure at the moment of the valve opening increases linearly with increasing the valve inlet pressure and the increased pilot pressure reduces the valve travel time. As the pilot pressure increases at the moment of valve opening, the time to start opening the valve is delayed resulting in increasing the valve opening time. With the increment of the valve inlet pressure, the valve opening time is mainly determined by the time required for the pilot pressure to start opening the valve. Therefore the design of a pilot gas supply system can readily control the valve inlet pressure at the valve opening as well as the amount of oxidizer supplied to a combustion chamber during the engine startup.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.8
• /
• pp.695-702
• /
• 2012

In this study, Multi-fidelity analysis is performed to improve the accuracy of analysis result during conceptual design stage. Multidisciplinary Design Optimization(MDO) method is also considered to satisfy the total system requirements. Low-fidelity analysis codes which are based on empirical equations are developed and validated for analyzing the Unmanned Aerial Vehicle(UAV) which have unconventional configurations. Analysis codes consist of initial sizing, aerodynamics, propulsion, mission, weight, performance, and stability modules. Design synthesis program which is composed of those modules is developed. To improve the accuracy of the design method for UAV, Vortex Lattice Method is used for the strategy of MFA. Multi-Disciplinary Feasible(MDF) method is used for MDO technique. To demonstrate the validity of presented method, the optimization results of both methods are compared. According to those results, the presented method is demonstrated to be applicable to improve the accuracy of the analyses during conceptual design stage.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.19 no.4
• /
• pp.37-43
• /
• 2011

Lunar exploration program has been prepared with the aim of launch in the 2020's. As part of it, a lunar lander demonstrator has been developed which is the model for verifying all the system, such as structure, propulsion and control system before launch to deep space. After verifying all the system, the demonstrator will be evaluated by flight test. This paper deals with path tracking controller based on thrusters for the demonstrator. For this, first we derive equations of motion according to the allocation of thrusters and design the path tracking controller. The signal generated from the controller is continuous so PWPF(Pulse-Width Pulse-Frequency) modulator is adopted for generating on/off signal. Finally MATLAB simulation is performed for evaluating the path tracking ability and the final landing velocity.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.126-133
• /
• 2022

This study proposes a suppression of zero sequence current (ZSC), which is caused by zero sequence voltage (ZSV) for a dual two-level inverter with single DC bus. Large output voltages enable the dual inverter with single DC bus to improve a system efficiency compared with single inverter. However, the structure of dual inverter with single DC bus inevitably generates ZSC, which reduces the system efficiency and causes a current ripple. ZSV is also produced by dead time, and its magnitude is determined by the DC bus and current direction. This study presents a novel space vector modulation method that allows the instantaneous suppression of ZSC. Based on a condition where a switching period is twice a sampling (control) period, the proposed control method is implemented by injecting the offset voltage at the primary inverter. This offset voltage is injected in half of the switching period to suppress the ZSC. Simulation and experiments are used to compare the proposed and conventional methods to determine the ZSC suppression performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.1
• /
• pp.1-11
• /
• 2021

POGO is a dynamic axial instability phenomenon that occurs in liquid-propelled rockets. As the natural frequencies of the fuselage and those of the propellant supply system become closer, the entire system will become unstable. To predict POGO, the propellant (oxidant and fuel) tank in the first stage is modeled as a shell element, and the remaining components, the engine and the upper part, are modeled as mass-spring, and structural analysis is performed. The transmission line model is used to predict the pressure and flow perturbation of the propellant supply system. In this paper, the closed-loop transfer function is constructed by integrating the fuselage structure and fluid modeling as described above. The pogo suppressor consists of a branch pipe and an accumulator that absorbs pressure fluctuations in a passive manner and is located in the middle of the propellant supply system. The design parameters for its design optimization to suppress the decay phenomenon are set as the diameter, length of the branch pipe, and accumulator. Multiple-objective function optimization is performed by setting the energy minimization of the closed loop transfer function in terms of to the mass of the pogo suppressor and that of the propellant as the objective function.

• Korean Journal of Remote Sensing
• /
• v.37 no.5_1
• /
• pp.927-938
• /
• 2021

A similar magnitude of non-gravitational perturbations are act on the formation flying low earth orbit satellites with a certain time difference. Using this temporal correlation, the non-gravity acceleration of the low earth orbiting satellites can be transferred for the othersatellites. There is a period in which the accelerometer data of one satellite is unavailable for GRACE and GRACE-FO satellites. In this case, the accelerometer data transplant method described above is officially used to recover the accelerometer data at the Jet Propulsion Laboratory (JPL). In this paper, we proposed a model for predicting accelerometer data of formation flying low earth orbit satellites using a neural network (NN) model to improve the estimation accuracy of the transplant method. Although the transplant method cannot reflect the satellite's position and space environmental factors, the NN model can use them as model inputs to increase the prediction accuracy. A prediction test of an accelerometer data using NN model was performed for one month, and the prediction accuracy was compared with the transplant method. The NN model outperformsthe transplant method with 55.0% and 40.1% error reduction in the along-track and radial directions, respectively.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.8-14
• /
• 2017

Gearboxes for power transmission of a rotorcraft transfer power generated by an engine to the fan and the pusher for up, down and forward flight. The gearboxes are divided into the main gearbox and the sub-gearbox. The main goal of the gearbox design is to design the weight as light as possible within a range that satisfies all given requirements (transmission power, mounting space, etc.). In particular, the initial conceptual design is very important to reduce the weight of the gearbox, since the weight can vary greatly depending on the system configuration, even if it has the same function. In this study, various conceptual designs of the gearbox according to the installation position of the engine were presented. Also, the element parts such as gears and bearings in each concept design were designed by sizing for their life, and the estimated weights of the conceptual system configuration were compared.