• Composites Research
• /
• v.13 no.3
• /
• pp.48-57
• /
• 2000

Fracture analysis of coating cracking on a substrate system described in a companion paper was applied and verified by four-point bending tests. The multiple cracking of coating was predicted using a fracture mechanics approach. The strain energy release rate (G) due to the formation of a new crack in a coating was obtained. A crack density vs. strain data of metallic and polymeric substrate was used to get the in-situ fracture toughness of coating with respect to various baking time and temperature. The $G_c$ was decreased as the baking temperature and time was increased. This paper gave insight about usefulness of four-point bending test for fracture toughness evaluation of coating and it gave a new method for in-situ coating toughness.

• Journal of the Korean Wood Science and Technology
• /
• v.49 no.2
• /
• pp.169-180
• /
• 2021

Inherent crystalline domains present in low formaldehyde to urea (F/U) molar ratio urea-formaldehyde (UF) resins are responsible for their poor adhesion in wood-based composite panels. To modify the crystallinity of low molar ratio (LMR) UF resins, this study investigates the additional effect of cellulose nanomaterials (CNMs), such as cellulose microfibrils (CMFs), cellulose nanofibrils (CNFs), and TEMPO-oxidized CNFs (TEMPO-CNFs) on the crystallinity of modified LMR UF resins. First, two modification methods (post-mixing and in situ) were compared for modified LMR UF resins with TEMPO-CNFs. The modified UF resins with TEMPO-CNFs decreased the nonvolatile solid contents, while increasing the viscosity and gel time. However, the in situ modification of UF resins with TEMPO-CNFs showed lower crystallinity than that of post-mixing. Then, the in situ method was compared for all CNMs to modify LMR UF resins. The modified UF resins with CMFs using the in situ method increased nonvolatile solid contents and viscosity but decreased the gel time. The crystallinity of UF resins modified with TEMPO-CNFs was the lowest even though the crystalline domains were not significantly changed for all modified UF resins. These results suggest that these CNMs should be modified to prevent the formation of crystalline domains in LMR UF resins.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1996.06a
• /
• pp.40-41
• /
• 1996

Nitridation technique has been receiving much attention for the formation of a thin nitrided buffer layer on which high quality nitride films can be formedl. Particularly, gallium nitride (GaN) has been considered as a promising material for blue-and ultraviolet-emitting devices. It can also be used for in situ formed and stable passivation layers for selective growth of $GaAs_2$. In this work, formation of a thin nitrided layer is investigated. Nitrogen electron cyclotron resonance(ECR)-plasma is employed for the formation of thin nitrided layer. The plasma source used in this work is a compact ECR plasma gun3 which is specifically designed to enhance control, and to provide in-situ monitoring of plasma parameters during plasma-assisted processing. Microwave power of 100-200 W was used to excite the plasma which was emitted from an orifice of 25 rnm in diameter. The substrate were positioned 15 em away from the orifice of plasma source. Prior to nitridation is performed, the surface of n-type (001)GaAs was exposed to hydrogen plasma for 20 min at $300{\;}^{\circ}C$ in order to eliminate a native oxide formed on GaAs surface. Change from ring to streak in RHEED pattern can be obtained through the irradiation of hydrogen plasma, indicating a clean surface. Nitridation was carried out for 5-40 min at $RT-600{\;}^{\circ}C$ in a ECR plasma-assisted molecular beam epitaxy system. Typical chamber pressure was $7.5{\times}lO^{-4}$ Torr during the nitridations at $N_2$ flow rate of 10 seem.(omitted)mitted)

• Molecules and Cells
• /
• v.26 no.6
• /
• pp.590-594
• /
• 2008

brc-2, an ortholog of BRCA2 in Caenorhabditis elegans, is essential in the maintenance of genetic integrity. In C. elegans, cellular location correlates with meiotic progression, and transgene-induced cosuppression is observed in the germ line but not in somatic cells. We used these unique features to dissect the role of brc-2 in the germ line from that in somatic cells. In situ hybridization of wild type animals revealed that brc-2 gene expression was higher in oocytes than in other germline cells, and was barely detectable in mitotic cells. In contrast, germ cells containing multicopies of the brc-2 transgene showed no significant in situ hybridization signal at any oogenesis stage, confirming that brc-2 expression was functionally cosuppressed in the transgenic germ line. RAD-51 foci formation in response to DNA damage was abrogated in brc-2-cosuppressed germ cells, whereas wild-type germ cells showed strong RAD-51 foci formation. These germ cells exhibited massive chromosome fragmentation and decompaction instead of six bivalent chromosomes in diakinesis. Accordingly, lethality was observed after the early stage of germline development. These results suggest that brc-2 plays essential roles in chromosome integrity in early prophase, and therefore is crucial in meiotic progression and embryonic survival.

• Journal of Korea Foundry Society
• /
• v.15 no.3
• /
• pp.272-282
• /
• 1995

Iron-based metal matrix composites have been recently investigated for the use of inexpensive abrasion resistance material. This paper carried out to investigate the in-situ reaction effects on the microstructural characteristics and the formation mechanism of tungsten carbides in a white cast iron matrix. The specimens of Fe-3.2%C-2.8%Si alloy cast-bonded with tungsten wire were cast in the metal mold and isothermally heat treated at $950^{\circ}C$ up to 48 hours. The typical microstructure of heat treated specimens showed the reaction layer of WC at the interface of tungsten wire and the carbon depletion zone between the WC layer and the matrix. During the formation of WC layer, if the carbon supply is insufficient due to the decarburization of matrix or the isolation of matrix by cast-bonded W wires, the reaction layer develops coarse hexagonal crystalline WC. From the microstructural investigation, it was found that the volume of WC layer and the carbon depletion zone increased linearly with the isothermal heat treating time. This results supported that the formation rate of WC in the white cast iron matrix is controlled by the interfacial reaction with a constant reaction rate.

• Korean Journal of Materials Research
• /
• v.16 no.1
• /
• pp.50-57
• /
• 2006

Phase mixtures of Titanium boride, nitride, and carbide powder were produced by the reduction of a mixture of titanium and boron oxides with carbon via a gas-solid phase reaction. Boron oxides produce a vapour phase or decompose to a metal sub-oxide gaseous species when reduced at elevated temperature. The mechanism of BO sub-oxide gas formation from $B_2O_3$ and its subsequent reduction to titanium diboride for the production of uniform size hexagonal platelets is explained. These gaseous phases are critical for the formation of boride, nitride and carbide ceramics. For the production of ceramic phase composite microstructures, the nitrogen partial pressure was the most critical factor. Some calculated equilibrium phase fields has been verified experimentally. The theoretical approach therefore identifies conditions for the formation of phase mixtures. The thermodynamic and kinetic factors that govern the phase constituents are also discussed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.264-265
• /
• 2008

While the reliability of bulk insulation has become important particularly in multilayer boards and embedded boards, electronics are to be used under various environments such as at high temperature and in high humidity. We observed internal space charge behavior for two types of epoxy composites under dc electric fields to investigate the influence of water at high temperature. In the case of glass/epoxy specimen, homocharge is observed at water-treated specimen, and spatial oscillations become clearer in the water-treated specimens. Electric field in the vicinity of the electrodes shows the injection of homocharge. In aramid/epoxy specimens, heterocharge is observed at water-treated specimens, i.e. negative charge accumulates near the anode, while positive charge accumulates near the cathode. Electric field is enhanced just before each electrode. In order to further examine the mechanism of space charge formation, we have developed a new system that allows in situ space charge observation during ion migration tests at high temperature and high humidity. Using this in situ system.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3133-3138
• /
• 2010

The electrochemical properties of the liposoluble vitamin $K_1$ adsorbed on bare and lipid coated glassy carbon electrodes (GCEs) were studied in unbuffered and well buffered aqueous media. The reduction products of vitamin $K_1$ were characterized by employing cyclic voltammetry and the in situ UV-visible spectroelectrochemical technique. The radical species of vitamin $K_1$ cannot be observed at the bare GCEs in well buffered media. The formation of the anion radical of vitamin $K_1$ was observed in unbuffered solutions above pH 5.9 or at the lipid coated GCE in a well-buffered solution. UV-visible absorption bands of neutral vitamin $K_1$ were observed at 260 nm and 330 nm, and a band corresponding to the anion radical species was observed at 450 nm. The derivative cyclic voltabsorptometric (DCVA) curves obtained for electrochemical reduction of vitamin $K_1$ confirmed the presence of both neutral and anion radical species. The anion radical of vitamin $K_1$ formed at the hydrophobic conditions with phosphatidylcholine (PC) lipid coated electrode was stable enough to be observed in the spectroelectrochemical experiments.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.8
• /
• pp.695-703
• /
• 2005

The objective of this study is to determine the effective thermal conductivity and thermal resistance values in test boreholes with three different fill materials. To evaluate these heat transfer properties, in-situ tests on four vertical boreholes were conducted by adding a monitored amount of heat to water over various test lengths. Two parameter estimation models, line-source and numerical one-dimensional models, for evaluation of thermal response test data were compared when applied on the same four data sets. Results show that the average thermal conductivity deviation between measured data and these two models is in the range of $3.03\%$ to $4.45\%$. The effect of increasing grout thermal conductivity from 1.34 to 1.82 $W/m^{\circ}C$ resulted in overall increases in effective formation thermal conductivity by $11.1\%$ to $51.9\%$ and reductions in borehole thermal resistance by $11.6\%$ to $26.1\%$.

• 한국전기화학회:학술대회논문집
• /
• 2002.11a
• /
• pp.57-65
• /
• 2002

The presence of tetragonal phase at the surface of $LiMn_2O_4$ pinicle due to a Jahn-Teller offset was previously reported to be one of the causes for capacity fading observed during cycling of $Li//Li_xMn_2O_4$ in 4V range. Further, it is reported that a Jahn-Teller effect in 4V range may be suppressed by substitution of Mn ions with Li ions or other transition metal ions. However, the direct evidence of the suppression of a Jahn-Teller effect in 4V range by substitution of Mn ions with other metal ions has not been reported. The dissolution and formation of surface film at the surface of $LiMn_2O_4$ electrodes also reportedly affect the capacity fading or rate capability. This study reports on the evidence of the onset and suppression of a Jahn-Teller effect in 4V range and the dissolution and formation of surface film at the surface of $LiMn_2O_4$ thin film electrodes using in situ bending beam method (BBM) in situ electrochemical quartz crystal microbalance (EQCM).