• 한국주조공학회지
• /
• 제20권3호
• /
• pp.188-196
• /
• 2000

A vacuum casting was proposed as a new fabrication method of Si wafer for solar cell substrate. It was tried to fabricate a Si plate with good properties and to reduce the production cost by direct vacuum casting. By $5{\sim}10$ cmHg of pressure difference Si plate with $50{\times}46{\times}1.5\;mm^3$ was fabricated. For the preventing of the reaction between graphite mold and Si melt, BN powder coating or BN insert were used. The Si wafer was poly crystalline with 100 ${\mu}m{\sim}1$ mm order of grain size. And there were some twins and dislocations in the grains.

• 한국재료학회지
• /
• 제9권9호
• /
• pp.883-889
• /
• 1999

직경이 각각 4,6,8,12 및 15mm인 순Al 또는 Al-(1,2,3wt%) Cu합금 내부냉금이 95mm ø$\times$200mm H 크기의 흑연주형 중심부에 설치되었다. 이 내부냉금과 같은 조성의 용융금속이 $750^{\circ}C$의 주입온도에서 주형에 주입되었고, 냉각속도, 응고조직 및 성분편석이 분석되었다. 주괴직경/내부냉금직경의 비가 8까지 증가될수록 결정립도, 2차수지상간격 및 성분편석이 현저하게 감소됨이 확인되었다. 그러나 이 비가 8이상이 되면, 미용해 내부냉금이 발생되고, 내부냉금의 효과는 급속히 감소되었다. 순Al 및 Al-(1,2,3wt%)Cu 합금에서 최대 내부냉금 효과를 얻을 수 있는 적정 주괴직경/내부냉금직경의 비는 $750^{\circ}C$주입온도에서는 8이었다.

• 산업기술연구
• /
• 제24권B호
• /
• pp.89-94
• /
• 2004

This Study is results of experimental works to investigate the characteristics of vibro-compaction of crushed stones having coarse grain sizes. For testing material, crushed stone, sieved within very narrow ranges of grain size distribution, was used. Cyclic loading apparatus was used to apply cyclic loading to the specimen prepared in the mold. Tests were performed by changing the ratio of the maximum to the minimum stress, frequency and the magnitude of the maximum and the minimum stresses. Settlement of specimen due to cyclic loading was measured to analyze the compaction efficiency and sieve analysis test after cyclic loading test was also carried out to find the crushing rate of the specimen. As results of cyclic loading test, normalized settlement in terms of specimen height tends to be converged around loading cycle number of 1500. The magnitude of normalized settlement is in the range of 3.11 ~ 8.57%. The crushing rate is in the range of 4.46 ~ 8.78%. Normalize settlement and the crushing rate tend to increase with decreasing the ratio of the maximum to the minimum stresses and they tend to increase with increasing the frequency and the magnitude of the maximum and the minimum stresses for the given ratio. In conclusions, compaction rate of crushed stone is controlled by the dynamic stress (difference between the maximum and the minimum stresses) and the crushing rate is dominated by applied energy to the specimen.

• 대한치과기공학회지
• /
• 제35권1호
• /
• pp.57-64
• /
• 2013

Purpose: Waste parts of zirconia blocks and powders were remained after CAD/CAM process. In order to make these residual zirconia fit for practical use, zirconia single cores were produced by drain casting process. Methods: Remained zirconia blocks were reduced to powders with zirconia mortar, and screened with 180 mesh sieve. Zirconia slip was prepared from waste parts of zirconia by ball milling. Plaster molds for forming cores by slip casting were also prepared. Formed cores were removed from mold after partial drying. Dried cores were biscuit fired at $1,100^{\circ}C$ for 1hour. Biscuit fired cores were treated with tools to control the fitness and thickness. Finished cores were $2^{nd}$ fired at $1,500^{\circ}C$ for 1hour. Microstructure of cross section of core was observed by SEM. Results: When mill pot was filled with 100g of zirconia and alumina mixed powder, 300g of zirconia ball, and 180g of distilled water, the optimum slip for drain casting was obtained. Gypsum plaster for ceramic forming was more suitable then yellow stone plaster for casting process. SEM photograph showed the microstructure of fully dense with uniform grain size of zirconia and well dispersed alumina grains into the zirconia matrix. Conclusion: Zirconia single cores were produced by drain casting process. Drain casting is useful process to make these residual zirconia fit for practical use. Further study will be focused on the preparation of the bridge type cores by casting.

• 한국농공학회지
• /
• 제23권3호
• /
• pp.96-104
• /
• 1981

In order to investigate the characteristics of the shear strength of the unsaturated cohesive soils which has mean characters of sand and clay widely used for banking, I selected soil samples from An-sung district and, against it, performed direct shear test and unconfined compression test changing grain size, compaction energy and moisture content and also performed triaxial compression test under optimum moisture content. The results are as follows; 1.As the passing percent of the No. 200 sieve increased from 23.6% to 56.1%, cohesion increased from 0. 202kg/cm2 to 0. 398kg/cm2 under the direct shear test and from 0.38 kg/cm2 to 1. 05kg/cm2 under the tria4al compression test, internal friction angle decreased from 44. 78$^{\circ}$ to 34. 34$^{\circ}$ under the direct shear test and from 31. 88$^{\circ}$ to 13. 31$^{\circ}$ under the triaxial compression test. 2.Cohesion showed it's maximum value around OMC and internal friction angle showed a tendency to increase according to the decrease of water content but it's increasing ratio was relatively slow. 3.Decreasing ratio of cohesion and internal friction angle was relatively sensitive according to the decrease of compaction energy. 4.The smaller of the vertical stress and the coarser of the grain size of samples, changing of the volume showed a tendency to increase and as the increase of water content, the shear displacement (dh) at failure shear stress ($\tau$f) showed maximum and the $\tau$f-dh curve was gentle. 5.To synthesize the results of the direct shear test and the triaxial compression test, cohesion showed higher under the triaxial compression test and internal friction angle showed a tendeney to appear higher under the direct shear test. It seems that we can get correspondent results by removing the side friction of mold with soils and adjusting the vertical stress and shearing speed under the direct shear test.

• 한국결정성장학회지
• /
• 제27권6호
• /
• pp.313-318
• /
• 2017

본 연구에서는 가스터빈용 Co계 합금인 ECY768 as-cast 합금 시편의 melt/mold 온도에 따른 결정구조 및 미세조직 및 변화를 고찰하였다. As-cast ECY768 샘플들은 전반적으로 amorphous 특성을 보여주고 있으며 기지인 Co상과 금속탄화물상으로 구성되어 있음을 확인하였으며, mold의 온도에 따른 XRD 패턴에서의 결정성 변화를 고찰하였다. 광학현미경(OM)을 이용하여 as-cast 샘플들의 결정립계에 석출물을 관찰하였다. 또한 FE-SEM에 의한 미세구조 분석시 Co기지상과 금속 탄화물의 석출물이 발견되는 영역이 관찰하였으며 EDS 분석에 의해 금속과 탄소의 화학양론이 확연히 다른 $M_{23}C_6$ 및 MC-type 조직으로 확인할 수 있었다. 여기서 $M_{23}C_6-type$의 탄화물은 Cr 원소를 주성분으로 하는 것을 확인할 수 있었으며, MC-type 탄화물은 Ta 원소가 주성분임을 확인할 수 있었다.

• 한국산학기술학회논문지
• /
• 제18권4호
• /
• pp.653-659
• /
• 2017

본 연구에서는 원웨이 클러치의 핵심 부품인 Outer Support Ring의 복합 단조 공정을 개발하고, 시제품을 제작하여 평가하였다. 기존 공정 즉, 열간 단조와 MCT 가공 공정은 과대한 소재 절삭량과 가공 시간이 길다는 단점이 있다. 이를 극복하고자 열간 단조를 통하여 형상을 구현하고, 냉간 단조를 통하여 정밀한 부품을 성형하였다. 최소한의 가공만을 적용하는 복합 단조 공정을 개발하였다. 상용 소프트웨어인 Deform-3D를 이용하여 단조 해석을 수행하였다. 해석 결과를 바탕으로 열간 단조 및 냉간 단조 공정을 설계하였고, 실제 금형 및 시제품을 제작하였다. 제작한 시제품은 경도, 표면 조도, 내부 결함, 단류선 검사 등의 평가를 수행하였다. 평가결과 특이한 문제점은 발견되지 않았으며, 양산적용이 가능할 것으로 판단된다. 복합 단조를 통하여 열간 단조와 MCT 가공 공정 대비 약 27%의 소재를 절감할 수 있었다. 또한 제품 개당 생산 시간은 약 2.15배 단축되었다. 본 연구를 통하여 원가 절감이 가능한 공정 및 금형 설계 기술을 확립하였고, 이를 통하여 관련 자동차 부품 생산에도 긍정적인 효과가 있을 것으로 기대된다.

• The Plant Pathology Journal
• /
• 제35권4호
• /
• pp.301-312
• /
• 2019

Sorghum is the fifth most important cereal worldwide, spreading from Africa throughout the world. It is particularly important in the semi-arid tropics due to its drought tolerance, and when cultivated in Southeast Asia commonly occurs as a second crop during the dry season. We recovered Fusarium from sorghum in Thailand and found F. proliferatum, F. thapsinum and F. verticillioides most frequently, and intermittent isolates of F. sacchari and F. beomiforme. The relatively high frequencies of F. proliferatum and F. verticillioides, suggest mycotoxin contamination, particularly fumonisins and moniliformin, should be evaluated. Genetic variation within the three commonly recovered species was characterized with vegetative compatibility, mating type, Amplified Fragment Length Polymorphisms (AFLPs), and female fertility. Effective population number ($N_e$) was highest for F. verticillioides and lowest for F. thapsinum with values based on mating type allele frequencies higher than those based on female fertility. Based on AFLP genetic variation, the F. thapsinum populations were the most closely related, the F. verticillioides populations were the most distantly related, and the F. proliferatum populations were in an intermediate position. The genetic variation observed could result if F. thapsinum is introduced primarily with seed, while F. proliferatum and F. verticillioides could arrive with seed or be carried over from previous crops, e.g., rice or maize, which sorghum is following. Confirmation of species transmission patterns is needed to understand the agricultural systems in which sorghum is grown in Southeast Asia, which are quite different from the systems found in Africa, Australia, India and the Americas.

• Progress in Superconductivity
• /
• 제10권2호
• /
• pp.103-107
• /
• 2009

$Bi_2Sr_2Ca_1Cu_2O_x$(BSCCO 2212) superconductors for current lead were fabricated by centrifugal melting process(CMP). BSCCO 2212 powder was melted at $1200^{\circ}\C$ in a resistance furnace using a Pt crucible and poured in a rotating cylindrical mold preheated at $550^{\circ}\C$ for 2 hour. The solidified BSCCO-2212 samples were heat-treated by partial melting process in oxygen atmosphere. The current-voltage curves at 77 K of the samples were obtained by transport measurement, and the microstructure was investigated by scanning electron microscope. The $J_c$ values at 77 K of the tubes partially melted at $840^{\circ}C,\;860^{\circ}C\;and\;880^{\circ}C$ were 492, 430 and 398 $A/cm^2$, respectively. It was observed that the plate-like grains in BSCCO 2212 tube was more developed in the sample heat-treated at $840^{\circ}C$. It was found that the critical current of the BSCCO 2212 samples was dependent on the partial melting schedule regarding the grain shape and size of the BSCCO 2212.

• 한국가구학회지
• /
• 제25권1호
• /
• pp.1-10
• /
• 2014

The First bentwood chairs in the world, called "winsor chairs" were made by British craftsman in the 17th century. Since then, from the start of NO.14 using solid bentwood by 19th-century German Michael Thonet, furniture making techniques such as Bent knee, Y-leg, X-leg- were developed based on Llaminated bentwood made by Alvar Aalto of Finland in the 20th century. In the 20th century Charles Eames of the United States studied Molded plywood, using plywood to produce a variety of furniture and during the 17~20 century a variety of Bentwood were developed. Coming into the 21st century, American Matthias Pliessnig and Phil Seaton worked with past Bentwood designs, developing Bentwood further by adapting Bentwood's know-how and IT technology. Science and technology evolved and Reholz of Germany developed technology which can mold three-dimensional wood using a new matarial called 3D-veneer, In the past only plastic or metal could be moulded 3 dimensional but now beautiful wood grain patterns can be molded by utilizing this technology. Also this is comparable with the past two-dimensional molding technology. In this Sustainable Design techniauses era, Bentwood fused with IT technology has great potential as a high-tech and eco-friendly techniche.