• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.277-284
• /
• 1996

The water test results indicated that the impurities had detrimetal effect on the wear resistance of silicon nitride and the effects were getting severe as the temperature increased. Especially when Ca existed as an impurity the detrimental effects was the most severe. These results were resulted from the fact that impurities lowered the mechanical properties of the grain boundary phase of silicon nitride. The wear test results of glass/glass-ceramic specimens having a similar composition to the grain boundary phase of silicon nitride revea-led that the specimen containing CaO showed the lowest wear resistance. The existence of Fe and Ca at the grain boundary phase assisted forming a grain boundary phase with relatively low refractoriness. Therefore at a given wear condition the removal of deformed layer would be easier. The results showed that the glass phases could be modified by heat-treatment and this modification improved tribological characteristics of the silicon nitride.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1794-1796
• /
• 1996

In order to evaluate the soundness of 10 year service-aged XLPE-insulated 22.9 kV underground distribution cables, semiconductive shields have been characterized. The edge of insulation near the insulation shield shows a drastic decrease of OIT. Impurities such as Ca, Mg, Fe, Cu were detected in both conductor and insulation shields. Their concentrations at the insulation shield are much higher than those at the strand shield. All these facts suggest that the edge of insulation near the insulation shield is degraded considerably, which might be attributed to the oxidation reaction of insulation by a large amount of impurities in the insulation shield.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.95-97
• /
• 2012

Recycled aggregate (RA) produced from demolished concrete waste can bring about several problems on concrete performance, when it is used as aggregate for new concrete. Because RA generally has lower quality than natural aggregate due to the residual cement paste attached on RA and various impurities. It is also very difficult to ensure that the quality of RA remains consistent, because generally RA is produced variously. Thus, in concrete recycling, it is extremely important to estimate the risk of the impurities which could affect performances of recycled aggregate concrete (RAC) focusing on the material flow of concrete waste and its recycling. This study suggests an evaluation result to expect the possibility of impurity mixing in RA production procedure. and suggests a risk evaluation model to expect the changes of RAC performances based on conventional data in Japan.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.541-544
• /
• 2002

The reflective liquid crystal(LC) imager in one panel Liquid Crystal on Silicon(LCoS) System must have the properties such as fast response time, high contrast ratio(C/R) and voltage holding ratio(VHR) which are more related to the lifetime of imager than the others. As the high-output light including a short wavelength from UHP lamp is exposed to LCoS imager, the indium metal impurities, which decrease the C/R and VHR, are diffused from ITO thin film on glass. To ensure the high reliable LCoS imager for HD projection TV, we have studied the effects of the plasma treatment on ITO film to reduce impurities in imager.

• Journal of the Korean Chemical Society
• /
• v.11 no.1
• /
• pp.33-37
• /
• 1967

The influence of impurities contained in Marmatite ores on leaching of zinc was investigated. The zinc sulfide having the same crystal structure of natural Sphalerite was prepared by heating the zinc sulfide chemically precipitated, at $650^{\circ}C$ in nitrogen atmosphere. The activation energy of the sample was 25.8 kcal per mole in the leach test when oxygen partial pressure was 5 atm. and the value was exceedingly high compared to that obtained in Marmatite ores. Synthetic zinc sulfides added with small amount of each impurities were treated in same procedure. As a result, it was found that the leaching velocity was accelerated sharply when about 1 percent of $Cu^{++}$ was blended to the sample. Larger amount of iron has also same effect but the effect was minor compared to the copper. The other impurities indicated no appreciable catalytic action.

• Corrosion Science and Technology
• /
• v.17 no.6
• /
• pp.265-271
• /
• 2018

CRUD specimens, scraped from twice-burned fuel cladding in the Korean Nuclear Power Plant, were analyzed using Shielded-EPMA. The principal elements of the CRUD were identified as Ni and Fe, at an approximate ratio of 1.3 Ni/Fe. To investigate the morphology and composition of the pure metallic materials in the CRUD, coolant impurities must be removed. This can be accomplished by increasing the EPMA current to an abnormally high intensity until the impurities are melted. Normally, EPMA applications are performed at conditions of 20 kV voltage and 20 nA current. But in our study, the applied current was increased up to 1200 nA, over time increments ranging from 5 to 30 seconds. This technique was performed by opening an adjustable aperture for the gun alignment. Results showed impurities contained in the CRUD material disappeared and pure metal materials, e.g., Ni and Fe, remained. This method presents an innovative way to analyze CRUD.

• Journal of Industrial Technology
• /
• v.41 no.1
• /
• pp.25-30
• /
• 2021

Hydride-dehydride process for efficient recycling of tantalum (Ta) is used for manufacturer of Ta powder. In case of metal powder, Impurities as like nitride, oxygen, hydrogen is decreased of physical properties. For manufacture of Ta powder, control of theses impurities is important. In this study, to decreased of impurities on Ta powder using HDH process optimize dehydride condition. Dehydration behavior of Ta is depended on temperature, time, and atmosphere. Phase transition of Ta hydride is analyzed by X-ray diffraction (XRD). Concentration of hydrogen is decreased with temperature increased. At high temperature, concentration of hydrogen in Ta is similar according to time increased. Size and morphology of powder is not observed after dehydride. Ta powder, which is less than 20 um, concentration of hydrogen under 800 ppm is obtain.

• Journal of Ceramic Processing Research
• /
• v.20 no.4
• /
• pp.388-394
• /
• 2019

In this study, high-purity single-walled carbon nanotubes (SWCNTs) were prepared by removing the unreacted metal constituents and amorphous carbon impurities using a post-annealing process. Unlike conventional thermal processing techniques, this technique involved different gas atmospheres for efficient removal of impurities. A heat treatment was conducted in the presence of chlorine, oxygen, and chlorine + oxygen gases. The nanotubes demonstrated the best characteristics, when the heat treatment was conducted in the presence of a mixture of chlorine and oxygen gases. The scanning electron microscopy, transmission electron microscopy, ultraviolet absorbance, and sheet resistance measurements showed that the heat treatment process efficiently removed the unreacted metal and amorphous carbon impurities from the as-synthesized SWCNTs. The high-purity SWCNTs exhibited improved electrical conductivities. Such high-purity SWCNTs can be used in various carbon composites for improving the sensitivity of gas sensors.

• Journal of the Korean Society of Radiology
• /
• v.11 no.5
• /
• pp.335-341
• /
• 2017

Cyclotron is a device that accelerates positrons or neutrons, and is used as a facility for making radioactive drugs having short half-lives. Such radioactive drugs are used for positron emission tomography (PET), which is a medical apparatus. In order to make radioactive drugs from a cyclotron, a nuclear reaction must occur between accelerated positrons and a target. After the reaction, unncessary neutrons are produced. In the present study, radioactivation generated from the collisions between the concrete shielding wall and the positrons and neutrons produced from the cyclotron is investigated. We tracked radioactivated radioactive isotopes by conducting experiments using FLUKA, a type of Monte Carlo simulation. The properties of the concrete shielding wall were comparatively analyzed using materials containing impurities at ppm level and materials that do not contain impurities. The generated radioactivated nuclear species were comparatively analyzed based on the exposure dose affecting human body as a criterion, through RESRAD-Build. The results of experiments showed that the material containing impurities produced a total of 14 radioactive isotopes, and $^{60}Co$(72.50%), $^{134}Cs$(16.75%), $^{54}Mn$(5.60%), $^{152}Eu$(4.08%), $^{154}Eu$(1.07%) accounted for 99.9% of the total dose according to the analysis having the exposure dose affecting human body as criterion. The $^{60}Co$ nuclear species showed the greatest risk of radiation exposure. The material that did not contain impurities produced a total of five nuclear species. Among the five nuclear species, 54Mn accounted for 99.9% of the exposure dose. There is a possibility that Cobalt can be generated by inducive nuclear reaction of positrons through the radioactivation process of $^{56}Fe$ instead of impurities. However, there was no radioactivation because only few positrons reached the concrete wall. The results of comparative analysis on exposure dose with respect to the presence of impurities indicated that the presence of impurities caused approximately 98% higher exposure dose. From this result, the main cause of radioactivation was identified as the small ppm-level amount of impurities.

• The Korean Journal of Pesticide Science
• /
• v.6 no.1
• /
• pp.31-35
• /
• 2002

Objectives of this study were to determine if impurities in technical grade benfuracarb inhibit glutathione-S-transferase and amidase and to identify structures of impurities in technical grade benfuracarb. Technical grade benfuracarb, active ingredient, and impurity inhibited glutathione-S-transferase, and their $I_{50}$ were $9.7{\times}10^{-4}M,\;>1.0{\times}10^{-3}M,\;1.8{\times}10^{-4}M$, respectively. Such inhibition, however, was not higher than that by ethacrynic acid, a selective inhibitor to GST. Technical grade benfuracarb, active ingredient, and impurity also inhibited amidase, and their $I_{50}$ were $6.0{\times}10^{-5}M,\;4.3{\times}10^{-4}M,\;7.6{\times}10^{-5}M$, respectively. Our results show that the inhibition of both detoxifying enzymes by impurities in benfuracarb was 10-fold lower than that by active ingredient, suggesting that both active ingredient and impurities are involved in the inhibition of both detoxifying enzymes. Of four impurities (IM $1{\sim}4$) that were separated from technical grade benfuracarb, IM 2 and IM 3 inhibited GST and amidase. Based on data from IR, $^1H$-NMR, $^{13}C$-NMR and MS, it was determined that IM 2 is ethyl-N-isopropylamino propionate and IM 3 is ethyl-N-isopropyl-N(chlorosulfenyl)aminopropionate.