• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.9
• /
• pp.651-655
• /
• 2013

$(Ba_{0.85}Ca_{0.15})(Ti_{0.9}Zr_{0.1})O_3$ + 0.04 wt% $CeO_2$ lead-free ceramics were synthesized by conventional sintering process and the effect of calcination temperature on microstructure, dielectric and piezoelectric properties were investigated. Improved piezoelectric properties have been observed at $1,125^{\circ}C$ calcination temperature which show the optimal electrical properties, $k_p$~0.457, $d_{33}$~367 pC/N, $Q_m$~158 and $T_c$~$85^{\circ}C$. These results show that the piezoelectric properties can be improved by appropriate calcination temperature.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.2
• /
• pp.244-249
• /
• 2019

SiO has a high theoretical capacity as a promising anode material candidate for high-energy-density Li-ion batteries. However, its practical application is still not widely used because of the large volume change that occurs during cycling. In this report, an active material containing a mixture of SiO and graphite was used to improve the insufficient energy density of the conventional anode with the support of multidimensional conducting agents. To relieve the isolation of the active materials from volume changes of SiO/graphite electrode, two types of conducting agents, namely, 1-dimensional VGCF and 0-dimensional Super-P, were introduced. The combination of VGCF and Super-P conducting agents efficiently maintained electrical pathways among particles in the electrode during cycling. We found that the electrochemical performances of cycleability and rate capability were greatly improved by employing the conducting agent combinations of VGCF and Super-P compared with the electrode using only single VGCF or single Super-P. We investigated the detailed failure mechanisms by using systematic electrochemical analyses.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.392-398
• /
• 2014

$Al_2O_3$-SiC composites reinforced with SiC whisker ($SiC_w$) were fabricated using three different methods. In the first, $Al_2O_3-SiC_w$ starting materials were used. In the second, $Al_2O_3-SiC_w$-SiC particles ($SiC_p$) were used, which was intended to enhance the mechanical properties by $SiC_p$ reinforcement. In the third method, reaction-sintering was used with mullite-Al-C-$SiC_w$ starting materials. After hot-pressing at $1750^{\circ}C$ and 30 MPa for 1 h, the composites fabricated using $Al_2O_3-SiC_w$ and $Al_2O_3-SiC_w-SiC_p$ showed strong mechanical properties, by which the effects of reinforcement by $SiC_w$ and $SiC_p$ were confirmed. On the other hand, the mechanical properties of the composite fabricated by reaction-sintering were found to be inferior to those of the other $Al_2O_3$-SiC composites owing to its relatively lower density and the presence of ${\gamma}-Al_2O_3$ and ${\gamma}-Al_{2.67}O_4$. The greatest hardness and $K_{1C}$ were 20.37 GPa for the composite fabricated using $Al_2O_3-SiC_w$, and $4.9MPa{\cdot}m^{1/2}$ using $Al_2O_3-SiC_w-SiC_p$, respectively, which were much improved over those from the monolithic $Al_2O_3$.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.3
• /
• pp.667-670
• /
• 2009

The understanding of behaviors of hydroperoxyl/superoxide anion radicals (${H_2O_2}^./{O_2}^{-.}$) generated from a photoirradiated $TiO_2$ surface is essential to improve the efficiency of $TiO_2$ photocatalytic reactions by decreasing the recombination of photoinduced electron-hole ($e^--h^+$) pairs. In contrast with previous studies, we found that ${H_2O_2}^./{O_2}^{-.}$ generated on the surface of illuminated $TiO_2$ particles are mobile. ${H_2O_2}^./{O_2}^{-.}$ formed by the photocatalysis of $TiO_2$ particles immobilized onto the inner surface of a coil-quartz tube were forced under a continuous flow through a knotted tubing reactor (KTR) and into the aqueous phase completely separated from the $TiO_2$ particles, and were measured by a chemiluminescence (CL) technique using 2-methyl-6-(p-methoxyphenyl)-3,7-dihydroimidazo[ 1,2-a]pyrazin-3-one (MCLA) as the reagent. The initial concentration of the ${H_2O_2}^./{O_2}^{-.}$ stream entering the KTR was determined by its half-life (98 s) at pH 5.8. We suggests that the efficiency of $TiO_2$ photocatalytic reactions may be further improved by utilizing the mobility of ${H_2O_2}^./{O_2}^{-.}$.

• Korean Journal of Materials Research
• /
• v.19 no.1
• /
• pp.33-36
• /
• 2009

Inorganic-organic composite thin-film-transistors (TFTs) of ZnO nanowire/Poly(3-hexylthiophene) (P3HT) were investigated by changing the nanowire densities inside the composites. Crystalline ZnO nanowires were synthesized via an aqueous solution method at a low temperature, and the nanowire densities inside the composites were controlled by changing the ultrasonifiaction time. The channel layers were prepared with composites by spin-coating at 2000 rpm, which was followed by annealing in a vacuum at $100^{\circ}C$ for 10 hours. Au/inorganic-organic composite layer/$SiO_2$ structures were fabricated and the mobility, $I_{on}/I_{off}$ ratio, and threshold voltage were then measured to analyze the electrical characteristics of the channel layer. Compared with a P3HT TFT, the electrical properties of TFT were found to be improved after increasing the nanowire density inside the composites. The mobility of the P3HT TFT was approximately $10^{-4}cm^2/V{\cdot}s$. However, the mobility of the ZnO nanowire/P3HT composite TFT was increased by two orders compared to that of the P3HT TFT. In terms of the $I_{on}/I_{off}$ ratio, the composite device showed a two-fold increase compared to that of the P3HT TFT.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.441-448
• /
• 2002

The electrical properties of the GaN-based green light emitting diodes(LEDs) with the Mg-doped p-GaN layer activated in $N_2$ or $O_2$ ambient have been compared. For the $N_2$ -ambient activation the current-voltage behavior of LEDs has been found to be improved when the Mg dopants activation was performed in the higher temperature. However, for the $O_2$-ambient activation the current-voltage characteristic has been observed to be enhanced when the Mg dopants activation was carried out in the lower temperature. The minimum forward voltage at 20mA was obtained to be 4.8 V for LEDs with the p-GaN layer activated at $900^{\circ}C$ in the $N_2$ ambient and 4.5V for LEDs with the p-GaN layer treated at $700^{\circ}C$ in the $O_2$ambient, repectively. The forward voltage reduction of the LEDs treated in the $O_2$-ambient may be related to the oxygen co-doping of the p-GaN layer during the activation process. The $O_2$ -ambient activation process is useful for the enhancement of the LED performance as well as the fabrication process since this process can activate the Mg dopants in the low temperature.

• Corrosion Science and Technology
• /
• v.6 no.5
• /
• pp.257-260
• /
• 2007

In order to further improve the corrosion resistance and wear resistance of the Ni-P coatings of electroless plating, electroless Ni-P/n-$Al_2O_3$ composite deposits were prepared by adding some nano $Al_2O_3$ Particles in Ni-P plating bath. The bath composition and proproties were studied in this paper. The orthogonal test was applied in order to get the new composite solution, taking the initial stable potential as evaluation standard and considering the elements correlation at the same time. The processing parameters have been optimized by single factor experiment in which the depositing speed was chosen as the evaluation standard. The results showed that the process is stable and the composite Ni-P/n-$Al_2O_3$ deposits werebright and smooth, whose hardness and corrosion resistance are much better than simple Ni-P coatings. Furthermore the surface appearance and structure of the composite Ni-P/n-$Al_2O_3$ coating were investigated by SEM and XRD method. It was proved that the coating surface is typical cystiform cells and its structure is amorphous. All test results ofcomposite coating showed that all various physical coating properties had been improved by adding nano-particles. The hardness of optimal coating is more than 600HV and increases to 1000HV after heat-treating, and its hardness is 20~50% higher than Ni-P coating. The rust points appeared in 200 hour by immersing the coating into the 10%HCl solution and the corrosive speed is $3{\times}10^{-3}mg/(cm^2{\cdot}h)$which was obtained after 300 hour. In the same condition Ni-P coating is $5.6{\times}10^{-3}mg/(cm^2{\cdot}h)$. The salt spray resistance of the layers can exceed 600h with the thickness $20{\mu}m$.

• Journal of Environmental Science International
• /
• v.19 no.5
• /
• pp.577-584
• /
• 2010

The generation of $TiO_2$ nanoparticles by a thermal decomposition of titanium tetraisopropoxide (TTIP) was carried out experimentally using a tubular electric furnace at various synthesis temperatures (700, 900, 1100 and $1300^{\circ}C$) and precursor heating temperatures (80, 95 and $110^{\circ}C$). Effects of degree of crystallinity, surface area and anatase mass fraction of those $TiO_2$ nanoparticles on photocatalytic properties such as decomposition of methylene blue was investigated. Results show that the primary particle diameter obtained from thermal decomposition of TTIP was considerably smaller than the commercial photocatalyst (Degussa, P25). Also, those specific surface areas were more than 134.4 $m^2$/g. Resultant $TiO_2$ nanoparticles showed improved photocatalytic activity compared with Deggusa P25. This is contributed to the higher degree of crystallinity, surface area and anatase mass fraction of $TiO_2$ nanoparticles compared with P25.

• Journal of Food Hygiene and Safety
• /
• v.13 no.3
• /
• pp.189-195
• /
• 1998

Comparative insecticidal efficiency between compounded pyrethroids and its preparations cooperated with several synergists was studied. As main components, Group A contained Permethrine.Phthalthrine, Group B contained Permethrine.Furameth rine and Group C contained Phthalthrine.Dichlorvos. As synergists Piperonyl Butoxide (P.B.O.), N-Octylbicycloheptene dicarboximide (MGK-264), Octachlorodipropylether (8-421) was cooperated in each group. These preparations was treated to either Blattella G. or Musca D. for comparing about insecticidal efficiency[Knock-down rate ($KT_{50},\;KT_{90}$) and cumulative mortaility(percent/hrs)]. When the synergists was added to each Group, the insecticidal efficiency was improved. The most potent synergists was P.B.O. and the potency was decreased in the rank order of S-421>MGK-264. The more the concentration of synergists was increased, the more the insecticidal efficiency was improved. The rank order was $1:5{\geq}1:4>1.3$ in all three groups. The mortality (percent) according to time was similar to either $KT_{50}\;or\;KT_{90}$. Knock-down rate was appropriate parameter for the indicator about potency.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.218-225
• /
• 2001

The electroless plating of a metallic nickel on PAN-based carbon fiber surfaces was carried out to improve mechanical interfacial properties of the carbon fiber/epoxy resin composites which were unidirectionally fabricated by a prepregging method. In this work, the influence of Ni-P alloy concentration showing brittle-to-ductile transition was investigated on interlaminar shear strength (ILSS) and impact strength of the composites. The surface properties of carbon fibers were also measured by X-ray photoelectron spectroscopy (XPS). As the result, the $O_{ls}$ /$O_{ls}$ ratio or Ni and P amounts were increased with increasing electroless nickel plating time but the ILSS were not significantly improved. However, the impact properties was significantly improved in the presence of Ni-P alloy in the carbon fiber surface, resulting in an increase of the ductility of the composites.