• 설비공학논문집
• /
• 제1권1호
• /
• pp.46-54
• /
• 1989

The purpose of this study is to obtain the dynamic characteristics of an absorption refrigerator powered by solar energy by experiments. Since the absorption refrigerator power by solar energy should have the characteristics which is suitable for the intermittence and rarity of solar energy, not only the characteristics of the steady state operations but also the partial load and the transient operations should be considered. The minimum available temperature of the storage tank should be known, and the absorption refrigerator can be suitably selected for air-conditioning systems. In this study, the experimental data of the transient state for on-off and warming-up operations has been obtained. Also the experiments are performed which test the minimum available temperature of the storage tank. The results show that it takes 1 hour to get to the steady state of the absorption refrigerator, and the minimum available temperature of the storage tank is about $68^{\circ}C$, and show that in the partial load operations the performance of the absorption refrigerator is improved by applying the modified control method to on-off operations.

• 한국자원식물학회지
• /
• 제19권6호
• /
• pp.687-691
• /
• 2006

This experiment was conducted on rice (cv. 2005 Thaoi) seeds to study whether priming with deep sea water (DSW) results in enhancement of seed emergence and seedling growth and to identify the optimum concentration of Deep Sea Water (DSW) for priming. Two experiments were conducted subsequently. In experiment 1, four concentrations of the DSW (10%, 20%, 30% and 40%), and in experiment 2, five concentrations of DSW (10%, 15%, 20%, 25% and 30%) were prepared and seeds were primed for 24 hours duration at $25^{\circ}C$. Beside this, hydro priming with plain water was also included as a control. Experiments were laid out in Completely Randomized Design (CRD) with three replications. Result showed that 20% DSW seed priming treatment had improved the emergence, seedling height, number of roots and root length as compare to other with DSW or without DSW treatments. Beyond 20% DSW priming (i.e. 25%, 30% and 40%) were not suitable for priming the seed. On the basis of seedlings growth parameters; emergence, seedling height, root number and length, and shoot root ratio, 20% DSW priming was the best priming treatment.

• 설비공학논문집
• /
• 제13권6호
• /
• pp.497-504
• /
• 2001

A study to improve the accuracy of a map-based compressor model with experiment was performed. Corrections on the effects of suction gas superheat and heat leakage from a compressor shell are required to apply the compressor amp model based on the empirical performance data(map) of compressor manufacturers to the actual system. So experiments to assess the effects of superheat and hat leakage were performed and the corrected equations were made. Compressors and refrigerant used in the experiment were the high pressure type rotary compressor and R-22, experiments were performed by compressor calorimeter. From the experiment, a volumetric efficiency correction factor$(F_ν)$ showed the value of 0.77, slightly higher than 0.75 proposed by Dabiri and Rice for low pressure type reciprocating compressor, and the heat leakage from the compressor shell turned out to be a factor that influenced the discharged mass flow rate. The relation between heat leakage of compressor shell and the variation of discharged mass flow rate from compressor was considered in compressor map modeling as an empirical function. With this function, the prediction accuracy of compressor model in system conditions was improved.

• 정보보호학회논문지
• /
• 제26권3호
• /
• pp.623-630
• /
• 2016

이기종 기기가 상호 연결되어 통신하는 IoT 환경에서는 모든 기기가 일정한 보안 수준을 갖추어야 한다. 그러나 통신 계산 기능이 제약된 기기에서는 상대적으로 암호 알고리즘의 성능이 저하되어 최적화 또는 효율적인 구현 방법이 필요하다. 본 논문에서는 ARX 경량 블록 암호를 대상으로 레지스터를 고려한 효율적인 Rotation 구현 방법을 연구한다. 실제 기기를 이용한 성능 측정을 통해 수정된 Rotation의 효율성을 실증적으로 검증한다. 실험 결과, 수정된 Rotation이 이전보다 개선된 성능을 보여주었으며, 특히, 16비트 MSP 환경에서 실제 기기와 시뮬레이션 성능 측정 결과 사이에 유의한 차이가 있음을 발견하였다.

• Steel and Composite Structures
• /
• 제12권1호
• /
• pp.53-72
• /
• 2012

In this study, the physically-based failure models for matrix and fibers in compression and tension loading are introduced. For the 3D stress based fiber kinking model a modification is proposed for calculation of the fiber misalignment angle. All of these models are implemented into the finite element code by using the advantage of damage variable and the numerical results are discussed. To investigate the matrix failure model, purely in-plane transverse compression experiments are carried out on the specimens made by Glass/Epoxy to obtain the fracture surface angle and then a comparison is made with the calculated numerical results. Furthermore, shear failure of $({\pm}45)_s$ model is investigated and the obtained numerical results are discussed and compared with available experimental results. Some experiments are also carried out on the woven laminated composites to investigate the fracture pattern in the matrix failure mode and shown that the presented matrix failure model can be used for the woven composites. Finally, the obtained numerical results for stress based fiber kinking model and improved ones (strain based model) are discussed and compared with each other and with the available results. The results show that these models can predict the kink band angle approximately.

• Steel and Composite Structures
• /
• 제20권3호
• /
• pp.599-621
• /
• 2016

In order to study the working mechanism of rectangular steel-concrete composite columns subjected to compression-bending load and further determine the seismic performance index, a bottom strengthened rectangular steel reinforced concrete (SRC) column with concealed steel plates and a bottom strengthened rectangular concrete filled steel tube (CFST) columns were proposed. Six column models with different configurations were tested under horizontal low cyclic loading. Based on the experiments, the load-bearing capacity, stiffness and degradation process, ductility, hysteretic energy dissipation capacity, and failure characteristics of the models were analyzed. The load-bearing capacity calculation formulas for a normal section and an oblique section of bottom strengthened rectangular steel-concrete composite columns were pesented and a finite element (FE) numerical simulation of the classical specimens was performed. The study shows that the load-bearing capacity, ductility, and seismic energy dissipation capacity of the bottom strengthened rectangular steel-concrete composite columns are significantly improved compared to the conventional rectangular steel-concrete composite columns and the results obtained from the calculation and the FE numerical simulation are in good agreement with those from the experiments. The rectangular steel-concrete composite column with bottom strengthened shows better seismic behavior and higher energy dissipation capacity under suitable constructional requirements and it can be applied to the structure design of high-rise buildings.

• 한국시뮬레이션학회논문지
• /
• 제27권3호
• /
• pp.75-87
• /
• 2018

춘천시는 세계적인 테마파크 중 하나인 레고랜드를 건설중에 있다. 본 연구에서는 춘천레고랜드를 대비한 시내 교통기반에 대한 분석을 수행하였다. 먼저, 레고랜드와 관련한 현 춘천시의 교통 상황을 검토하였고 이를 기반으로 잠재적인 고객 및 도착률, 도로, 레고랜드로 진입 경로에 대한 정의를 수행하였다. 교통 상태를 반영하는 평가치인 점유율을 기반으로 분석을 위한 실험을 설계하였고 시뮬레이션을 통해 결과를 얻었다. 피크시즌에 심한 교통 체증이 예상되며 특히 도로 9,11,16에서 정도가 특히 심각하다는 결과이다. 이 도로들의 차선수 증가를 통한 추가적인 실험을 수행하였으며 시내 교통상 큰 개선된 결과를 도출하였다.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.93-98
• /
• 2005

The purpose of this study is to confirm the improvement of formability of AZ31 magnesium alloy sheet by using local heating and cooling technique. For this, the experiments of warm deep drawing were done under the temperatures of $100^{\circ}C\~400^{\circ}C$, and the punch velocity of 10, 100mm/min. Also FE analysis under the temperatures of blankholder and die of $150^{\circ}C,\;225^{\circ}C\;and\;300^{\circ}C$ for tools(holder and die) was executed with considering heat teansfer. From the results, the formability of AZ31 magnesium alloy, espicially the temperatures of $225^{\circ}C\~250^{\circ}C$ for tools(holder and die)improved remarkably. And the experiments and simulations showed that necking under room temperature for tools occured under the part of punch shoulder while at $300^{\circ}C$ for tools, at the part of die shoulder.

• Journal of Biosystems Engineering
• /
• 제14권3호
• /
• pp.168-180
• /
• 1989

This study was attempted to develop the electronic-hydraulic hitch control system for position control of tractor plow and investigate the control performance of the system through experiments. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in position control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. The following conclusions were derived from the study; 1. For the position control system operated on on-off control mode, positions of implement were controlled within ${\pm}0.73^{\circ}{\sim}{\pm}1.46^{\circ}$ in rockshaft angle to the reference position when the hydraulic flow rates were 5~15 l/min. For the position control system operated on PWM control mode, positions of implement were controlled within ${\pm}0.73^{\circ}$ to the reference position regardless of hydraulic flow rates. It means that the implement could be positioned more accurately to the reference position on PWM control mode than on on-off control mode. 2. As results of the frequency responses of the position control systems, no clear difference in control performance between on-off control and PWM control modes was found. As the hydraulic flow rates increased, the corner frequencies of amplitude attenuation and phase-angle change increased. It means that the control performance of the system could be improved as the hydraulic flow rate increases.

• 한국산학기술학회논문지
• /
• 제11권7호
• /
• pp.2317-2322
• /
• 2010

신성장 동력 산업으로 분류된 LED 조명등은 점차 수요가 확대되고 있으나 본격적인 대중화를 이루기 위해서는 여전히 LED 방열 설계 최적화를 통한 긴 수명과 고효율 확보가 매우 중요하다고 하겠다. 본 연구에서는 기존 10W LED 조명등에 비하여 방열 성능이 더욱 개선된 LED 조명등을 개발하고자 하였다. 이를 위하여 기존 램프의 방열 성능 실험을 통하여 수치해석 모델을 완성하였고 이러한 수치 모델을 이용하여 방열핀 형상, PCB 종류 및 LED 개수 등과 같은 방열 설계 인자들을 최적화하였다. 또한, 시제품을 제작한 후 방열 성능을 실험으로 검증함으로써 방열 성능이 획기적으로 개선된 10W LED 조명등을 성공적으로 개발하였다.