• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.1
• /
• pp.46-54
• /
• 1989

The purpose of this study is to obtain the dynamic characteristics of an absorption refrigerator powered by solar energy by experiments. Since the absorption refrigerator power by solar energy should have the characteristics which is suitable for the intermittence and rarity of solar energy, not only the characteristics of the steady state operations but also the partial load and the transient operations should be considered. The minimum available temperature of the storage tank should be known, and the absorption refrigerator can be suitably selected for air-conditioning systems. In this study, the experimental data of the transient state for on-off and warming-up operations has been obtained. Also the experiments are performed which test the minimum available temperature of the storage tank. The results show that it takes 1 hour to get to the steady state of the absorption refrigerator, and the minimum available temperature of the storage tank is about $68^{\circ}C$, and show that in the partial load operations the performance of the absorption refrigerator is improved by applying the modified control method to on-off operations.

• Korean Journal of Plant Resources
• /
• v.19 no.6
• /
• pp.687-691
• /
• 2006

This experiment was conducted on rice (cv. 2005 Thaoi) seeds to study whether priming with deep sea water (DSW) results in enhancement of seed emergence and seedling growth and to identify the optimum concentration of Deep Sea Water (DSW) for priming. Two experiments were conducted subsequently. In experiment 1, four concentrations of the DSW (10%, 20%, 30% and 40%), and in experiment 2, five concentrations of DSW (10%, 15%, 20%, 25% and 30%) were prepared and seeds were primed for 24 hours duration at $25^{\circ}C$. Beside this, hydro priming with plain water was also included as a control. Experiments were laid out in Completely Randomized Design (CRD) with three replications. Result showed that 20% DSW seed priming treatment had improved the emergence, seedling height, number of roots and root length as compare to other with DSW or without DSW treatments. Beyond 20% DSW priming (i.e. 25%, 30% and 40%) were not suitable for priming the seed. On the basis of seedlings growth parameters; emergence, seedling height, root number and length, and shoot root ratio, 20% DSW priming was the best priming treatment.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.6
• /
• pp.497-504
• /
• 2001

A study to improve the accuracy of a map-based compressor model with experiment was performed. Corrections on the effects of suction gas superheat and heat leakage from a compressor shell are required to apply the compressor amp model based on the empirical performance data(map) of compressor manufacturers to the actual system. So experiments to assess the effects of superheat and hat leakage were performed and the corrected equations were made. Compressors and refrigerant used in the experiment were the high pressure type rotary compressor and R-22, experiments were performed by compressor calorimeter. From the experiment, a volumetric efficiency correction factor$(F_ν)$ showed the value of 0.77, slightly higher than 0.75 proposed by Dabiri and Rice for low pressure type reciprocating compressor, and the heat leakage from the compressor shell turned out to be a factor that influenced the discharged mass flow rate. The relation between heat leakage of compressor shell and the variation of discharged mass flow rate from compressor was considered in compressor map modeling as an empirical function. With this function, the prediction accuracy of compressor model in system conditions was improved.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.26 no.3
• /
• pp.623-630
• /
• 2016

Heterogeneous IoT devices must satisfy a certain level of security for mutual connections and communications. However, a performance degradation of cryptographic algorithms in resource constrained devices is inevitable and so an optimization or efficient implementation method is necessary. In this paper, we study an efficient implementation method for rotation operations regarding registers for running ARX lightweight block ciphers. In a practical sense, we investigate the performance of modified rotation operations through experiments using real experiment devices. We show the improved performance of modified rotation operations and discover the significant difference in measured performance between simulations and real experiments, particularly for 16-bit MSP microcontrollers.

• Steel and Composite Structures
• /
• v.12 no.1
• /
• pp.53-72
• /
• 2012

In this study, the physically-based failure models for matrix and fibers in compression and tension loading are introduced. For the 3D stress based fiber kinking model a modification is proposed for calculation of the fiber misalignment angle. All of these models are implemented into the finite element code by using the advantage of damage variable and the numerical results are discussed. To investigate the matrix failure model, purely in-plane transverse compression experiments are carried out on the specimens made by Glass/Epoxy to obtain the fracture surface angle and then a comparison is made with the calculated numerical results. Furthermore, shear failure of $({\pm}45)_s$ model is investigated and the obtained numerical results are discussed and compared with available experimental results. Some experiments are also carried out on the woven laminated composites to investigate the fracture pattern in the matrix failure mode and shown that the presented matrix failure model can be used for the woven composites. Finally, the obtained numerical results for stress based fiber kinking model and improved ones (strain based model) are discussed and compared with each other and with the available results. The results show that these models can predict the kink band angle approximately.

• Steel and Composite Structures
• /
• v.20 no.3
• /
• pp.599-621
• /
• 2016

In order to study the working mechanism of rectangular steel-concrete composite columns subjected to compression-bending load and further determine the seismic performance index, a bottom strengthened rectangular steel reinforced concrete (SRC) column with concealed steel plates and a bottom strengthened rectangular concrete filled steel tube (CFST) columns were proposed. Six column models with different configurations were tested under horizontal low cyclic loading. Based on the experiments, the load-bearing capacity, stiffness and degradation process, ductility, hysteretic energy dissipation capacity, and failure characteristics of the models were analyzed. The load-bearing capacity calculation formulas for a normal section and an oblique section of bottom strengthened rectangular steel-concrete composite columns were pesented and a finite element (FE) numerical simulation of the classical specimens was performed. The study shows that the load-bearing capacity, ductility, and seismic energy dissipation capacity of the bottom strengthened rectangular steel-concrete composite columns are significantly improved compared to the conventional rectangular steel-concrete composite columns and the results obtained from the calculation and the FE numerical simulation are in good agreement with those from the experiments. The rectangular steel-concrete composite column with bottom strengthened shows better seismic behavior and higher energy dissipation capacity under suitable constructional requirements and it can be applied to the structure design of high-rise buildings.

• Journal of the Korea Society for Simulation
• /
• v.27 no.3
• /
• pp.75-87
• /
• 2018

Chuncheon city is constructing a world-wide famous theme park, Chuncheon Legoland. In this study, analysis of the city traffic infrastructure for Chuncheon Legoland has been performed. We first reviewed the current city traffic condition with regard to the park. We then defined potential customers and arrivals, streets, and routing street sequences to the park. Based on a measure, occupation ratio, reflecting traffic condition we designed experiments for analysis and obtained results from simulation. Our results indicate that severe traffic delay is expected during the peak season and is significant especially in streets 9,11,16. We performed additional experiments with increasing the number of lanes of them and obtained improved results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.93-98
• /
• 2005

The purpose of this study is to confirm the improvement of formability of AZ31 magnesium alloy sheet by using local heating and cooling technique. For this, the experiments of warm deep drawing were done under the temperatures of $100^{\circ}C\~400^{\circ}C$, and the punch velocity of 10, 100mm/min. Also FE analysis under the temperatures of blankholder and die of $150^{\circ}C,\;225^{\circ}C\;and\;300^{\circ}C$ for tools(holder and die) was executed with considering heat teansfer. From the results, the formability of AZ31 magnesium alloy, espicially the temperatures of $225^{\circ}C\~250^{\circ}C$ for tools(holder and die)improved remarkably. And the experiments and simulations showed that necking under room temperature for tools occured under the part of punch shoulder while at $300^{\circ}C$ for tools, at the part of die shoulder.

• Journal of Biosystems Engineering
• /
• v.14 no.3
• /
• pp.168-180
• /
• 1989

This study was attempted to develop the electronic-hydraulic hitch control system for position control of tractor plow and investigate the control performance of the system through experiments. Experiments were carried out to investigate the responses of the system to the step and sinusoidal inputs in position control. The effects of control mode, hydraulic flow rate, reference deadband, and proportional constant on control performance of the system were investigated. The following conclusions were derived from the study; 1. For the position control system operated on on-off control mode, positions of implement were controlled within ${\pm}0.73^{\circ}{\sim}{\pm}1.46^{\circ}$ in rockshaft angle to the reference position when the hydraulic flow rates were 5~15 l/min. For the position control system operated on PWM control mode, positions of implement were controlled within ${\pm}0.73^{\circ}$ to the reference position regardless of hydraulic flow rates. It means that the implement could be positioned more accurately to the reference position on PWM control mode than on on-off control mode. 2. As results of the frequency responses of the position control systems, no clear difference in control performance between on-off control and PWM control modes was found. As the hydraulic flow rates increased, the corner frequencies of amplitude attenuation and phase-angle change increased. It means that the control performance of the system could be improved as the hydraulic flow rate increases.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2317-2322
• /
• 2010

Market for LED lights as a newly-growing industry has been growing, and secureness of high efficiency and long life through optimal thermal design are crucial for further popularization. In this study, considerable improvement in thermal performance for a 10W LED light has been done compared to a previous model. For this, numerical model has been established through experiments and used to optimize design factors in heat release such as fin shape, PCB kind or LED number etc. Furthermore, prototype of a LED light has been made and the improved thermal performance was verified with heat release experiments.