• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.4
• /
• pp.426-435
• /
• 2013

In this paper, we propose the MIMO circular polarization feed network to enhance the communication performances from the previous $2{\times}2$ MIMO channel to $4{\times}4$ channel for Land Mobile Satellite communication system. The only possibility to extend the communication channel is to use the additional satellite because of the limitation of satellite spaces to install additional antennas. For overcoming this problems, we propose the MIMO circular polarization feed network to secure the isolation characteristics without the distant antenna space. The port isolation characteristics and each port impedance matching conditions are numerically verified and we suggest the $4{\times}4$ MIMO channel model of the proposed system and the performances are verified. The fabricated circular polarization patch antennas with the proposed feed network are measured in the reverberation chamber and 7~10 dB of diversity gain and 80 % increasement of channel capacity are obtained.

• Journal of IKEEE
• /
• v.12 no.3
• /
• pp.144-150
• /
• 2008

This paper describes the design of a coplanar-stripline(CPS) antenna without via hole in microstrip patch type for 910MHz RFID tags using the HFSS simulator. In order to obtain the simplified fabrication design of the antenna, we have used only an impedance matching network to match the impedance of a RFID-tag chip to that of the antenna, not using bandpass filter(BPF). In advance of the optimized antenna design, we have obtained and shown a good agreement compared with the published antenna for 5.8GHz in order to verify the simulation parameters in the HFSS. Based on the verified simulation parameters in the HFSS, we have designed and optimized the 910MHz-CPS-type microstrip patch antenna. The designed simulation results of the antenna show that the proposed antenna is very proper for RFID tags with the 910MHz center frequency without via hole in the microstrip patch antenna.

• Journal of Broadcast Engineering
• /
• v.19 no.6
• /
• pp.934-941
• /
• 2014

In this paper, we present a low profile 2-layered meander built-in monopole antenna for portable RFID reader using FDTD(Finite Difference Time Domain) method. The input impedance, return loss, and VSWR in the frequency domain are calculated by Fourier transforming the time domain results. The double meander 2-layer structure is used to enhance the impedance matching and increase the antenna gain. The measured bandwidth of the antenna is 0.895 GHz ~ 0.930 GHz for a S11 of less than -10dB. The measured peak gain of proposed low profile RFID built-in antenna is 2.3 dBi. And the proposed built-in antenna for portable RFID reader can offers relatively wide-bandwidth and high-gain characteristics, in respectively. Experimental data for the return loss and the gain of the antenna are also presented, and they are relatively in good agreement with the FDTD results. This antenna can be also applied to mobile communication field, energy fields, RFID, and home-network operations, broadcasting, and other low profile mobile systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.35-41
• /
• 1997

A series-fed microstrip array antenna of beamwidth $10^{\circ}$, squint angle $80^{\circ}$ and SLL -15 dB below is designed. Series-fed arrays are formed by interconnecting all the elements by high-impedance transmission lines and feeding the power at the first element and it is a traveling-wave antenna which is terminated with a matched load. Radiation patterns and impedance matching of the antenna are analyzed by Ensemble 4.0, which is a popular software package for designing printed antennas and arrays. The squint angle of beam can be controlled by the spacing between the elements. The major advantages of series-fed array antennas are that feed arangement is compact and the losses associated with the feeding network are less than those of a corporate feed type. The antennas are fabricated on the RT/Duroid Laminates of 62 mil thickness. The experimental results are very close to the specifications to be designed.

• Journal of Sensor Science and Technology
• /
• v.25 no.1
• /
• pp.46-50
• /
• 2016

During KSTAR plasma experiments, torsional $Alfv\acute{e}n$ waves in the frequency of few GHz or below were detected. To understand this plasma waves during the crash of MHD instabilities, an RF spectrometer has been developed for detection of the radiated RF signals in the KSTAR Tokamak. It has the capability of broadband RF spectral measurement (50 ~ 400 MHz). To detect the broadband RF signals which are radiated from the KSTAR systems, a broadband antenna is the key feature of the RF spectrometer. In this paper, a broadband bowtie antenna for detection of $Alfv\acute{e}n$-waves in the KSTAR Tokamak is presented. Planar-type bowtie antenna is designed and fabricated on an FR4 substrate with thickness of 1.6 mm. The antenna consists of bowtie shaped balanced radiators and broadband planar balun. The antenna is designed to have an input impedance of 50 Ohm, and a taper-shaped balun is adopted for field and impedance matching between 50 Ohm transmission line to 110 Ohm feeding network of balanced radiators. The implemented antenna provides around -3 to 3 dBi of gain for the whole frequency band. The VSWR of the bowtie antenna is less than 12:1 over the frequency bandwidth of 50 to 2000 MHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.77-84
• /
• 2007

In this parer, a wideband low-noise amplifier (LNA) has been realized in a 0.18mm CMOS technology for the applications of subsampling direct-conversion RF receivers. By exploiting the inverter-type transimpedance input stage with a 3rd-order Chebyshev matching network, the wideband LNA demonstrates the measured results of the -3dB bandwidth of 5.35GHz, the power gain (S21) of $12\sim18dB$, the noise figure (NF) of $6.9\sim10.8dB$, and the broadband input/output impedance matching of less than -10dB/-24dB within the bandwidth, respectively. The chip dissipates 32.4mW from a single 1.8V supply, and occupies the area of $0.56\times1.0mm^2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.10 s.113
• /
• pp.929-934
• /
• 2006

In the paper, we suggest a simpler synthesis technique for capacitively-coupled match circuit(CCMC) which have a function of DC block and impedance matching simultaneously, and introduce a stability margin analysis technique for designing microwave amplifier under conditionally stable state. Stability margin analysis is used to determine optimum match point that ensure maximum gain under the given stability margin. It can reduce time consuming work for selecting match points in the conditionally stable state. Also, suggested miniaturization scheme of matching network is distinguished from previous work with respect to reducing deterministic parameters for CCMC synthesis. To verify utility of suggested method, 24 GHz gain block is fabricated under conditionally stable state using an internal thin-film fabrication process, Measured results show a stable gain of 10 dB and flatness of 1 dB, which is well coincident with simulated one.

• ETRI Journal
• /
• v.35 no.1
• /
• pp.51-57
• /
• 2013

In this paper, a small internal antenna for a mobile handset is presented using multiband, wideband, and high-isolation multiple-input multiple-output techniques. The proposed antenna consists of three planar inverted-F antennas (PIFAs) that operate in the global system for mobile communication (GSM900), the digital communication system (DCS), the personal communication system (PCS), the universal mobile telecommunication system (UMTS), and wireless local area network (WLAN) bands with a physical size of $40mm{\times}10mm{\times}10mm$. A resonator attached to the folded PIFA creates dual resonances, achieving a wide bandwidth of approximately 460 MHz, covering the DCS, PCS, and UMTS bands; a meander shorting line is used to improve impedance matching. Additionally, a modified neutralization link is embedded between diversity antennas to enhance isolation, which results in a 6-dB improvement in the isolation and less than 0.1 in the envelope correlation coefficient evaluated from the far-field radiation patterns. Simulation and measurements demonstrate very similar results for S-parameters and radiation patterns. Peak gains show 3.73 dBi, 3.77 dBi, 3.28 dBi, 2.15 dBi, and 5.86 dBi, and antenna efficiencies show 56.15%, 72.15%, 68.59%, 52.92%, and 82.93% for GSM900, DCS, PCS, UMTS, and WLAN bands, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.511-518
• /
• 2006

In this paper, a small RFID tag antenna in UHF band which has bandwidth-enhanced characteristic is proposed. The shape of the proposed antenna is a meander antenna to have size-reduced characteristic, and it consists of two radiators which make dual resonance in adjacent frequency to enhance bandwidth. By adjusting length and location of each radiator, the proposed antenna can make dual resonance at arbitrary location on the Smith chart, which is able to make impedance matching with RFID tag chip in wide frequency range. And it is apparent that the proposed antenna can have bandwidth-enhanced characteristic according to the simulated and measured results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2434-2440
• /
• 2018

A new type of piezoelectric micromachined ultrasonic transducer (pMUT) with high resonant frequency was developed by using a thin lead zirconate titanate (PZT) as an insulation layer on a floating $10{\mu}m$ silicon membrane. The PZT insulation layer facilitated acoustic impedance matching at active pMUT, leading to a high performance in the acoustic conversion property compared with the transducer using $SiO_2$ insulation layer. The fabricated ultrasonic devices were wirelessly measured by connecting two identical acoustic transducers to two separate ports in a single network analyzer simultaneously. The acoustic wave emitted from a transducer induced a $3.16{\mu}W$ on the other side of the transducer at a distance of 2 cm. The transducer performances in terms of device diameters, PZT thickness, annealings, and different DC polings, etc. were investigated. COMSOL simulation was also performed to predict the device performances prior to fabrication. Based on the COMSOL simulation, the device was fabricated and the results were compared.