• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11b
• /
• pp.118-121
• /
• 2005

The acoustical performance of porous materials is determined by their seven or more macroscopic physical properties. However, it is not easy to measure all these properties in many cases. Furthermore, the measurement is compels engineers to spend much times. The effect of each property on the normal incidence absorption coefficient and normalized surface impedance was studied to estimate the properties of porous materials by numerical method. According to the investigation, Properties of porous materials are divided into several groups and estimated by each group. This paper is focused on the estimation procedure of porous materials by the numerical method.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.5
• /
• pp.67-71
• /
• 2010

This paper proposes new dual-band impedance transformers based on the L-section circuit topology. The proposed circuits consist of a transmission line section with a stub line either at the source or at the load end. The dual-band operating conditions are analyzed in detail and simple design equations are derived in terms of the line lengths and impedances for the different circuit topologies and load conditions. The dual-band operation is confirmed through the design, fabrication and measurement in microstrip circuits based on the proposed method.

• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.51-54
• /
• 2002

As digital systems continue to use components with faster edge rate and clock speeds, transmission of the digital information can take place many troubles. The increasing requirement for controlled impedance PCBs becomes both a critical success factor and a design challenge. Especially, the noise sources in digital system include the noise in power supply, ground and packaging due to simultaneous switching of signal, signal reflections and distortions on single and multiple transmission lines. This paper simulates the tracks controlled impedance with the test coupon. So, it can saves the design time and supports the economical PCB design.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.150-154
• /
• 2003

In this letter, a novel compact duplexer which consists of Tx and Rx Filter using microstrip line ${\lambda}/4$ resonators with a pair of tap-connected open-ended stepped impedance stubs is designed. The tapped open stubs not only work as K-inverters but also introduce attenuation poles, attenuation poles are located at upper and lower side of the passband by adjusting the open stub length and width. The result of measurement duplexer has been yielded better isolation and sharper skirt behavior than that with a conventional bandpass filter and similar to those of simulation results.

• Proceedings of the KOSOMBE Conference
• /
• v.1989 no.05
• /
• pp.71-73
• /
• 1989

The origins of the motion artifact resulting from exercise in impedance cardiography wore explained and the ensemble average technique was applied to reduce the motion artifact enabling the measurement of cardiac output during exercise. Algorithm for ensemble average was developed and applied to the actual impedance signals. It was found that the minimum number of sampling was 20, and sampling frequency was 500Hz. Using the ensemble average technique it was possible to measure cardiac output continuously during the treadmill exercise. Therefore it is hoped that this study may contribute in the area of exercise physiology and sport medicine.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.316-321
• /
• 2002

In this Paper, the channel characteristics of the medium voltage(22.9kV) power line to analysis the broadband power line communication in the frequency range up to 30MHz was measured. With the sideband electrical coupler in the operating frequency range from DC to 30MHz, we measured characteristic impedance, noise and attenuation of the medium voltage power line, and then characteristic impedance was measured at the state of unloaded medium voltage power line by Scattering parameter method of Vector Network Analyzer. As a measurement result, Channel impedance shows 100~380$\Omega$ at the less than 15MHz and 70~230$\Omega$ at the more than 15 MHz. Noise characteristics of power line shows -75dBm at 20MHz and Narrowband interference noise was from 3 MHz to 7MHz.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1012-1220
• /
• 1994

BaTiO3 ceramics doped with 0.1 to 4.0 mol% Nb2O5 were prepared by conventional solid stage sintering process, so as to investigate the effect of the amount of Nb2O5 on the dielectric properties and complex impedance patterns of barium titanates. From the measurement of capacitance, we found that the dielectric constant of BaTiO3 samples with 1 mol% or more Nb2O5 remained approximately constant around room temperature with values higher than 2500. In this paper, the effect of impurity content as well as temperature on complex impedance patterns was discussed in detail. In particular, the grain and grain boundary behavior of samples which showed PTCR characteristics was discussed in terms of measuring temperature.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.6
• /
• pp.79-88
• /
• 1998

This study was conducted to measure the moisture content of soil using RF impedance in the range of 1 to 30MHz. Considering the water potential flow in the soils, two types of sensor such as parallel cylinder and perpendicular plate type were fabricated and tested. The capacitance and resistance of sonsors for soil samples having moisture content range of 2 to 27% were measured by Q-meter (HP4342). The higher soil moisture content was and the larger soil bulk density was, the more the capacitance of sensors increased. To eliminate the effect of bulk density on measuring soil moisture content using RF impedance, two kinds of model having the density independent functions such as the ratio of capacitance change to conductance change and weight of water and dry soils respectively were developed and estimated by regression analysis.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.69-72
• /
• 2008

This paper presents the transient and conventional grounding impedance behaviors of large grid grounding system associated with the injection point of impulse current The measurement methods consider two possible errors in the grounding-system impedances: (1) ground mutual resistance due to current flow through ground from the ground electrode to be measured to the current auxiliary, (2) ac mutual coupling between the current test lead and the potential test lead The test circuit was set to reduce the error factors. The transient grounding impedance depends on the rise time and injection point of impulse current It is effective that grounding conductor is connected to the center of the large grid grounding system.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.5
• /
• pp.488-495
• /
• 2007

In this paper, SBN (Structure-Borne Noise) reduction of resiliently mounted machinery and effect of the foundation impedance on mount performance is studied. SBN reduction through the mount is analyzed by using two theoretical models; mass-spring model and wave model, in which longitudinal wave propagation is included. It is found that floor impedance greatly affects SBN reduction through lower mount, while it is almost negligible to SBN reduction through upper mount. Comparisons between measurement and predictions shows that the mass-spring model is valid only in low frequency range below few hundred Hz, while for high frequency ranges longitudinal wave propagation in the mount must be considered.