• 한국소음진동공학회논문집
• /
• 제26권3호
• /
• pp.290-297
• /
• 2016

This paper deals with the vibration characteristics of a reciprocal compressor with variable rotating speed according to the change of operating frequencies. The equation of motion and exciting force of the equivalent compressor model were formulated, and the vibration responses at operating frequencies were predicted. The predicted results were compared with the measured results. Although the predicted results had little errors in operating condition, it represented good agreement in general. Especially, the natural frequencies obtained from the measurement were similar to those calculated by the eigenvalue problem of the equivalent model. The procedure and results in this paper can be utilized to the identification of the vibration characteristics of new compressor models.

• 전기학회논문지
• /
• 제66권6호
• /
• pp.911-915
• /
• 2017

Recently, there has been an increasing interest in the non-contact power transmission method of magnetic gears. Since there is no mechanical contact, noise caused by friction can be reduced, and even if a sudden large force is applied, the impact of the gear is close to zero. Further, since the power is transmitted by the magnetic flux, it has high reliability. However, there is a problem that a loss due to a magnetic field due to use of a magnetic flux. The loss caused by the magnetic field of the magnetic gear is a joule loss called eddy current loss. In addition, the eddy current loss in the magnetic gear largely occurs in the permanent magnet, but it is a fatal loss to the permanent magnet which is vulnerable to heat. Particularly, magnetic gears requiring high torque density use NdFeB series permanent magnets, and this permanent magnets have a characteristic in which the magnetic force decreases as temperature increases. Therefore, in this paper, the eddy current loss of the permanent magnet according to the permanent magnet attaching method is analyzed in order to reduce the eddy current loss of the permanent magnet. We have proposed a structure that can reduce the eddy current loss through the analysis and show the effect of reducing the loss of the proposed structure.

• 한국기계가공학회지
• /
• 제18권2호
• /
• pp.65-72
• /
• 2019

In long freight trains, there is a brake time delay in neighboring freight cars, which causes damage and fractures in the couplers, especially at their knuckle. A problem in the couplers of the cars can cause derailment and damages of human life and property. In this study, maximum forces on the couplers are studied when a long freight car brakes with the brake delay time and coupler gap. We make a dynamic model of 50 freight cars and couplers, applying contact between the couplers and a characteristic curve to express the force and displacement of the buffers using SIMPACK, which is a multi-body dynamics program. We use EN 14531-2, which is a standard of freight car brakes, to verify the dynamic model. Then, we compare the analyzed impact force with the coupler knuckle standard after applying the two carriages of a locomotive in the model based on the dispersed double head control system. The result shows that all coupler gap conditions satisfy the infinite lifetime of the material when the brake delay time is 0.1 second.

• 품질경영학회지
• /
• 제48권1호
• /
• pp.149-169
• /
• 2020

Purpose: This study analyzes the characteristics of the Quality Management performed by SMEs in the Defense Industry in supply chains and analyzes the effect of the continuous improvement activities based on cooperation. Especially, for Military Supplies, the suitability of products is usually decided by judging their conformity to the specification, and from this structural characteristic, this study would analyze the structural relationship of systematic improvement activities with Supply Chain Quality Management(SCQM) and Business Performance(BP). Methods: Continuous improvement activities(CI) have significance as the driver force for the promotion of Quality Management. Thus, this study analyzed the causal relationships from the perspective of the process among CI, SCQM and BP. For an analysis of the structural characteristics and causal relationships among the constituents, AMOS was used, and 297 companies in the Defense Industry were utilized as samples. Results: It turned out that CI had significant impacts on Management Infra(MGT_Infra), Process Management(PM), Human Resources Management(HRM) and Communication(COMU) and had an indirect impact on the enterprises' financial performance through the parameters of HRM and Communication. Meanwhile, it turned out that between CI and non-financial performance, there was a direct effect, and there was also an indirect effect through the variables of the Management Infra and Communication. Conclusion: It turned out that CI had a positive effect on SCQM as a proactive driver and that they had significant relationships with BP(financial, Non-financial), both financial performance and non-financial performance. However, PM did not have a significant relationship of effect with BP because of the character appearing by the evaluation method of military supplies for the conformity to the specifications.

• Wind and Structures
• /
• 제30권4호
• /
• pp.433-450
• /
• 2020

The strong turbulence characteristic of typhoon not only will significantly change flow field characteristics surrounding the large-scale wind turbine and aerodynamic force distribution on surface, but also may cause morphological evolution of coast dune and thereby form sand storms. A 5MW horizontal-axis wind turbine in a wind power plant of southeastern coastal areas in China was chosen to investigate the distribution law of additional loads caused by wind-sand coupling movement of coast dune at landing of strong typhoons. Firstly, a mesoscale Weather Research and Forecasting (WRF) mode was introduced in for high spatial resolution simulation of typhoon "Megi". Wind speed profile on the boundary layer of typhoon was gained through fitting based on nonlinear least squares and then it was integrated into the user-defined function (UDF) as an entry condition of small-scaled CFD numerical simulation. On this basis, a synchronous iterative modeling of wind field and sand particle combination was carried out by using a continuous phase and discrete phase. Influencing laws of typhoon and normal wind on moving characteristics of sand particles, equivalent pressure distribution mode of structural surface and characteristics of lift resistance coefficient were compared. Results demonstrated that: Compared with normal wind, mesoscale typhoon intensifies the 3D aerodynamic distribution mode on structural surface of wind turbine significantly. Different from wind loads, sand loads mainly impact on 30° ranges at two sides of the lower windward region on the tower. The ratio between sand loads and wind load reaches 3.937% and the maximum sand pressure coefficient is 0.09. The coupling impact effect of strong typhoon and large sand particles is more significant, in which the resistance coefficient of tower is increased by 9.80% to the maximum extent. The maximum resistance coefficient in typhoon field is 13.79% higher than that in the normal wind field.

• 한국의류산업학회지
• /
• 제18권1호
• /
• pp.120-129
• /
• 2016

This study aimed to develop an optimal sizing system and a draping pattern for hip protector based on an analysis of anthropometric characteristics of Korean older women. A hip protector is a specialized form of pants or underwear containing pads along the outside of each hip. The 3D body scan data of Korean older women were analyzed to identify their anthropometric characteristics and a four-size system with 93% of population accommodation was developed by clustering analysis based on key dimensions derived from factor analysis. The sizing system consists of small/short, large/short, small/tall, and large/tall. A 3D physical model and hip pads were fabricated; then, a hip protector was draped on the 3D model and hip pads. The sizing system of hip protector was analyzed in terms of size and shape and a draping pattern was compared on back center, back side, front side, front center and pad. Lastly, the pattern deformation and clothing pressure were analyzed using the virtual clothing system CLO. Virtual system have disadvantage of not to suggest the objective value. In the future research the wearing comfort and impact absorption of the hip protector needs to be tested and then a hip protector design will be finalized by considering the hip protector's size, material, comfort testing results, aesthetic appeal, protection effectiveness, and practical utility of everyday use.

• 정보화정책
• /
• 제21권1호
• /
• pp.35-56
• /
• 2014

ICT가 도입되면서, 업무의 수행이 예전에 비해서 파편화되고 있다. 파편화는 업무의 연속성을 해친다는 측면에서 생산성에 부정적일 수 있지만, 일의 파편화를 잘 관리하여 조합한다면 업무의 모드를 효과적으로 미래형으로 전환하여 생산성을 향상시킬 수도 있을 것이다. 본 연구에서는 일의 파편화가 어떠한 유형으로 나타나고, 유형에 따라 업무의 특성들은 어떻게 다른지를 조사 분석 하였다. 이러한 연구목적을 달성하기 위해 파편화의 종류와 정도, 그리고 ICT 사용을 포함한 업무의 특성에 관해서 설문을 구성하였고 이를 활용하여 데이터를 수집하였다. 실제 기업 근무자들을 대상으로 수집한 300건의 설문 응답을 분석에 사용하였다. 군집분석을 통해 업무 시간/공간 편중형, 업무 시간 분산형, 업무 공간 분산형, 업무 시간/공간 파편형의 4가지 군집 유형을 도출하였다. 군집별로 업무 영역, 경력, 업무의 특성, ICT 사용에 대한 특성들의 차이를 분석하였다. 결론에서는 이렇게 변화하여 나가고 있는 업무 특성의 본질적인 변화를 수용하기 위해서는 어떠한 정책과 대응책이 필요한지, 본 분석의 시사점들을 중심으로 논의하였다.

• International Journal of Computer Science & Network Security
• /
• 제24권7호
• /
• pp.73-78
• /
• 2024

The present world is full of challenges and opportunities for the women at work. Every woman works hard for academic growth and professional development. For the same reason they also face challenges every day such as stresses, tensions, problems and competitions. When these factors exceed above the strengths, the capabilities of a woman start drowning under stress. Stress is generally thought negative characteristic, but stress or tension maintained up to some level is necessary and effective towards work done at job. This paper covers the study relationship between job stressor and female teacher's performance. The study was carried out in Government Colleges of District Hyderabad, Pakistan. The teacher student relationship was selected as a stressor for female teachers. The study is descriptive in nature followed by method of correlation. A five point "Likert Scale" was developed to collect the data from the sample size of 158 college teachers drawn randomly and the collected data was assessed quantitatively. The relationship between the "teacher student" (as an indicator of job stress) and "female teachers' performance" was calculated by Pearson Correlation formula. The findings of the study show the significant correlations between the teacher student relationship and job stress in female teachers' performance where it is found that the stressor caused the poor Physical and Mental health of female teachers working in colleges.

• 한국산학기술학회논문지
• /
• 제19권4호
• /
• pp.571-577
• /
• 2018

본 선회다짐기는 도로 현장에서 가장 많이 사용하는 다짐 롤러의 다짐 특성을 반영하기 위해 개발된 실내 다짐장비이다. 기존의 충격을 이용한 프록터 다짐과는 달리 압축력과 회전을 통한 전단력을 이용한 현장 롤러의 다짐특성을 모사하였다. 본 연구의 목적은 기존의 프록터 다짐과정에서 얻기 힘든 전단응력 및 다짐중의 밀도변화 특성 등을 선회다짐기를 이용하여 평가하고, 이를 도로설계에 반영할 수 있는 기초자료로 활용하는 것이다. 이러한 선회다짐기를 이용하여 도로 현장 및 지하매설물 시공 시 가장 많이 사용되는 모래 및 노상토의 다짐 특성을 분석 및 평가하였다. 선회다짐기를 이용한 다짐 특성은 기본적으로 선회다짐 횟수와 시편의 높이, 다짐밀도, 간극비, 포화도 및 전단응력이다. 선회다짐 횟수가 증가할수록 시편의 높이는 작아지고, 간극비는 작아지고, 다짐 밀도는 증가하고, 포화도는 증가하며, 전단응력은 커지는 경향을 보였다. 전단응력은 다짐 초기에 200kPa 수준에서 시작하여 선회다짐 횟수 50회 정도가 되면 대략 330-350 kPa 수준으로 증가하였다. 동일한 시편의 경우 함수비가 커짐에 따라 다짐 밀도, 포화도 및 전단응력이 증가하는 경향을 보였다. 선회다짐기를 이용한 다짐은 밀도 및 전단응력 등 도로 설계 시 필요한 물성을 측정할 수 있는 장점을 가지고 있어 이를 도로설계시 반영한다면 더 공학적인 도로설계를 할 수 있을 것이다.

• 자원리싸이클링
• /
• 제29권2호
• /
• pp.28-36
• /
• 2020

폐유리병을 순환 잔골재로 활용하여 재활용률을 향상시키기 위해 다양한 파분쇄 산물의 입도, 입형, 에너지 분석을 통해서 재활용 공정에 적용할 수 있는 최적의 장비 선정을 위한 파분쇄 특성 연구를 수행하였다. 파분쇄시 발생하는 힘의 종류인 충격, 압축, 마모가 특징적으로 나타는 장비인 해머크러셔, 슈레더 및 롤크러셔, 볼밀 총 4가지 장비를 선정하여 실험을 진행하였다. 각 장비의 파분쇄 산물의 입도분석을 수행한 결과 슈레더에서 발생한 산물만이 콘크리트용, 아크팔트용 순환 잔골재의 품질 기준을 만족시키는 것으로 확인되었다. 화상소프트웨어(Image J, National institute of health)를 이용한 입형 분석 결과 대부분 입자의 입형이 1.6 이하의 값을 가지고 있어 순환 잔골재로 재활용하기에 위험성이 적고 편장석 비율 규정 조건 또한 충족하는 것으로 판단되었다. 또한 각 장비에서 소모되는 에너지를 측정해본 결과 에너지 대비 입자의 감소 비율이 슈레더의 산물이 가장 높은 것으로 확인되었다. 따라서 10mm 이하의 일정 입도구간에서 폐유리병 파분쇄시 적용될 수 있는 최적의 장비는 슈레더임을 판단할 수 있었다. 본 연구를 통해서 폐유리병 파분쇄 공정의 에너지 효율 및 제품의 경쟁력 향상에 큰 기여를 할 수 있을 것이라고 사료된다.