• 대한디지털의료영상학회논문지
• /
• 제11권2호
• /
• pp.115-119
• /
• 2009

I think this will be valuable reference for assuring consistency and homogeneity of clarity and managing dental radiation equipment by experimentation of dental radiation equipment permanent which based on KS C IEC 61223-3-4 standard and KS C IEC 61223-2-7. Put a dental radiation generator and experiment equipment as source and film(sensor) length within 30 em, place the step-wedge above the film(sensor). Tie up tube voltage 60 kVp, tube current 7 mA and then get an each image through CCD sensor and film by changing the exposure time as 0.12sec, 0.25sec, 0.4sec. Repeat the test 5times as a same method. Measure the concentration of each stage of film image, which gained by experiment, using photometer. And the image that gained by CCD sensor, analyze the pixel value's change by using image J, which is analyzing image program provided by NIH(National Institutes of Health). In case of film, while 0.12sec and 0.25sec show regular rising pattern of density gap as exposure time's increase, 0.4sec shows low rather than 0.12sec and 0.25sec. In case of CCD sensor density test, the result shows opposite pattern of film. This makes me think that pixels of CCD's sensor can have 0~255 value but it becomes saturation if the value is over 255. The way that getting clear reception during decreasing human's exposed radiation is one of maintaining an equipment as a best condition. So we should keeping a dental radiation equipment's condition steadily through cyclic permanent test after factor examination. Even digital equipment doesn't maintain a permanent, it can maintain a clarity by post processing of image so that hard to set it as standard of permanent test. Therefore it would be more increase the accuracy that compare a film as standard image. Thus I consider it will be an important measurement to care for dental radiation equipment and warrant homogeneity, consistency of dental image's clarity through comparing pattern which is the result from factor test against cyclic permanent test.

• 한국멀티미디어학회논문지
• /
• 제8권12호
• /
• pp.1565-1571
• /
• 2005

Images reconstructed with Maximum-Likelihood Expectation-Maximization (MLEM) algorithm have been observed to have checkerboard effects and have noise artifacts near edges as iterations proceed. To compensate this ill-posed nature, numerous penalized maximum-likelihood methods have been proposed. We suggest a simple algorithm of applying edge detecting process to the MLEM and Bayesian Expectation-Maximization (BEM) to reduce the noise artifacts near edges and remove checkerboard effects. We have shown by simulation that this algorithm removes checkerboard effects and improves the clarity of the reconstructed image and has good properties based on root mean square error (RMS).

• 한국인터넷방송통신학회논문지
• /
• 제9권1호
• /
• pp.75-87
• /
• 2009

본 논문에서 이미지 선명도 함수의 최적화에 의해 융합 법칙이 유도되는 새로운 이미지 융합 접근법을 제안한다. 선명도 함수에 비교하여 소스 이미지로부터 최적 블록을 통계적으로 선택하기 위하여 유전자 알고리듬이 사용되었다. 변이 연산에 의해 만들어진 유전인자들의 포격을 통해서 찾아진 재능 유전 인자를 갖는 새로운 네스티드 유전자 알고리듬을 설계하였고 구현하였다. 알고리듬의 수렴은 해석적으로, 실험적으로 그리고 통계적으로 3개의 테스트 함수를 사용하여 표준 GA와 비교하였다. 결과의 GA는 변수와 집단 크기에 불변이며, 최소 20 개체이면 시험에 충분하다는 것을 알 수 있었다. 융합 응용에서 모집단내의 각 개체는 입력 블록을 나타내는 유한한 이산 값을 갖는 개체이다. 이미지 융합 실험에 제안한 기법의 성능은 출력 품질 척도로 상호 정보량(MI)으로 특징지워진다. 제안한 방법은 C=2 입력 이미지에 대해 테스트되었다. 제안한 방법의 실험 결과는 현재의 다중 초점 이미지 융합 기법에 대한 실제적이고 매력적인 대안이 됨을 보여준다.

• Communications for Statistical Applications and Methods
• /
• 제4권3호
• /
• pp.817-825
• /
• 1997

Images reconstructed with EM algorithm have been observed to have checkerboard effects and have large distortions near edges as iterations proceed. We suggest a aimple algorithm of applying line process to the EM and Bayesian EM to reduce the distortions near edges. We show by simulation that this algorithm improves the clarity of the reconstructed image and has good properties based on root mean square error.

• International Journal of Computer Science & Network Security
• /
• 제23권4호
• /
• pp.39-47
• /
• 2023

This study compares various transformation techniques for multifocus image fusion. Multi-focus image fusion is a procedure of merging multiple images captured at unalike focus distances to produce a single composite image with improved sharpness and clarity. In this research, the purpose is to compare different popular frequency domain approaches for multi-focus image fusion, such as Discrete Wavelet Transforms (DWT), Stationary Wavelet Transforms (SWT), DCT-based Laplacian Pyramid (DCT-LP), Discrete Cosine Harmonic Wavelet Transform (DC-HWT), and Dual-Tree Complex Wavelet Transform (DT-CWT). The objective is to increase the understanding of these transformation techniques and how they can be utilized in conjunction with one another. The analysis will evaluate the 10 most crucial parameters and highlight the unique features of each method. The results will help determine which transformation technique is the best for multi-focus image fusion applications. Based on the visual and statistical analysis, it is suggested that the DCT-LP is the most appropriate technique, but the results also provide valuable insights into choosing the right approach.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.505-511
• /
• 1993

The results were obtained with changes according to the surface roughness of work roll and method to make the peak count on the roll in the temper rolling, and factors to affect to the work roll surface in actual rolling machine(ie. Temper mill). Conclusions are as follows. 1. E.D.T(Electro-discharge texturing)roll is more uniform roughness distribution than shot blasted roll and it's life time is two timees longer than that of shot blasted because it has more sine wave roughness. 2. The higher peak count of surface roughness, the more time is necessary to work roll texturing In shot blasting method, Surface roughness is relating to the grit size,impeller speed and hardness of roll material, But is can't control the peak count. 3. In shot blast texturing, Surface roughness of temper rolled strip which is transfered surface roughness of work roll is more ununiform than that of E.D.T roll 4. E.D.T roll has more uniform than the shot blasted roll and has more peak count than that of shot blasted roll. The surface of painted strip to image clarity is superior to that of shot blasted roll because E.D.T roll has more peak count and smooth surface.

• KSTLE International Journal
• /
• 제2권1호
• /
• pp.80-84
• /
• 2001

The purpose of this paper is to show the result from the study to improve the formability and appearance which is important in the cold rolled strip, the coated strip and prepainted strip. Furthermore, to give appropriate surface roughness, shape of work roll for temper mill is also important. The strip has a greater peak counts and homogeneous roughness. This makes the prepainted surface smooth and consistent in appearance with good image clarity. Therefore, the surface roughness of the work roll is very important. The reason that surface roughness of the work roll is transferred to the strip surface is the rolling farce and tension at the temper rolling or cold rolling. This study is classified in order to get an accurate and homogeneous roughness. There are few papers published in this field, because its importance is not known and the proper operation of the machine is not generally well known. This paper investigates the correlation between strip surface roughness and the surface of the work roll. After studying the surface roughness and shape according to the texturing method for roll surfaces at temper rolling, the findings were as follows. Irregular surface roughness can be compensated with several paint coatings, but this also makes the quality deteriorate and manufacturing costs go up.

• 한국정밀공학회지
• /
• 제12권5호
• /
• pp.69-76
• /
• 1995

This paper describes characteristics of EDT(Electro Discharge Texturing) and that the strip surface has influence on the paintability. The pulse mode and the capacitor mode of recently developed EDT method were investigated about the peak shape and the roughness of strip surface. And EDT method compared the above-mentioned contents with the SBT(Shot Blast Texturing) method. The peak count of the pulse mode is more than that of the capacitor mode. But the lower roughness below the Ra 3.2 .mu. m of the strip surface, the texturing time of the pulse mode is longer than the capacitor mode. In SBT method, the peak shape is similar to capacitor mode. But the EDT roll has more uniformity than the SBT roll and has more peak count than that of SBT roll. Therefore, in the painted steel sheet, EDT roll gives better surface of clarity image than the SBT roll.

• 교육녹색환경연구
• /
• 제12권3호
• /
• pp.58-67
• /
• 2013

This study is to analyze the satisfaction and the image evaluation of landscape elements in outdoor space by types of the university campus. The results are as follows. 1) Out of outdoor elements at university campus, planting area, resting area, access road, and water feature are recognized as major landscape elements. Among them, planting area and access roads are evaluated low in terms of satisfaction levels, therefore, improvement on these elements are required. 2) In outdoor space image evaluation, university campus has image such as 'simple', 'clear', and 'safe'. By scale of universities, both 'A' university, which is the biggest in terms of size of campus, and 'B' university, which has a medium sized campus, have a positive image. However, 'C' university, which is the smallest in terms of size of campus, has a passive and negative image. 3) 6 factors are extracted through Factor Analysis for image evaluation. All of the universities show positive image in the categories of 'clarity' and 'familiarity', however, 'B' university and 'C' university show negative image in the category of 'scale'. 4) In Correlation Analysis between landscape elements satisfaction level and image evaluation, it is showed that the group of landscape facility becomes a relation factor of overall image evaluation. As a result, the higher satisfaction level goes, the better image evaluation of overall outdoor space at university campus is.

• 한국컴퓨터그래픽스학회논문지
• /
• 제24권3호
• /
• pp.43-48
• /
• 2018

본 연구는 핸드폰과 같은 모바일 기기로 촬영한 문서 이미지에서 조명 조건들로 인해 발생한 부드러운 그림자를 제거하는 방법을 제안한다. 본 방법은 기존의 피라미드 기반 방법이나, 경계법 방법에 비해 더 좋은 결과를 만들어 낸다. 방법의 기본아이디어는 촬영된 문서 이미지로부터 이미지 지역 통계를 활용하여 글자나 그림 등의 흥미로운 내용이 있는 부분을 분리하고, 이 분리된 부분에 대해 적응적인 밝기 및 대조 조정과 레벨 변환을 수행하여 이미지를 더욱 선명하게 하는 것이다. 또한 내용이 없는 부분에 대해서는 부드러운 채움을 위해 이미지 변형량 기반의 빈 곳 메우기 방법을 이용한다.