• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.42.2-42.2
• /
• 2010

Transparent conducting oxides (TCOs) are of significant importance for their applications in various devices, such as light-emitting diodes, thin-film solar cells, organic light-emitting diodes, liquid crystal displays, and so on. In order for TCOs to contribute to the performance improvement of these devices, TCOs should have high transmittance and good electrical properties simultaneously. Sn-doped $In_2O_3$ (ITO) is the most commonly used TCO. However, indium is toxic and scarce in nature. Thus, ZnO has attracted a lot of attention because of the possibility for replacing ITO. In particular, group III impurity-doped ZnO showed the optoelectronic properties comparable to those of ITO electrodes. Al-doped ZnO exhibited the best performance among various doped ZnO films because of the high substitutional doping efficiency. However, in order for the Al-doped ZnO to replace ITO in electronic devices, their electrical and optical properties should further significantly be improved. In this connection, different ways such as a variation of deposition conditions, different deposition techniques, and post-deposition annealing processes have been investigated so far. Among the deposition methods, RF magnetron sputtering has been extensively used because of the easiness in controlling deposition parameters and its fast deposition rate. In addition, when combined with post-deposition annealing in a reducing ambient, the optoelectronic properties of Al-doped ZnO films were found to be further improved. In this presentation, we deposited Al-doped ZnO (ZnO:$Al_2O_3$ = 98:2 wt%) thin films on the glass and sapphire substrates using RF magnetron sputtering as a function of substrate temperature. In addition, the ZnO samples were annealed in different conditions, e.g., rapid thermal annealing (RTA) at $900^{\circ}C$ in $N_2$ ambient for 1 min, tube-furnace annealing at $500^{\circ}C$ in $N_2:H_2$=9:1 gas flow for 1 hour, or RTA combined with tube-furnace annealing. It is found that the mobilities and carrier concentrations of the samples are dependent on growth temperature followed by one of three subsequent post-deposition annealing conditions.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2005

High quality indium tin oxide (ITO) thin films were grown by pulse laser deposition (PLD) on flexible polyethersulphone (PES) substrates. The electrical, optical, and surface morphological properties of these films were examined as a function of substrate temperature and oxygen pressure. ITO thin films, deposited by PLD on a PES substrate at room temperature and an oxygen pressure of 15 mTorr, have a low electrical resistivity of $2.9{\times}10^{-4}{\Omega}cm$ and a high optical transmittance of 84 % in the visible range. They were used as the anode in organic light-emitting diodes (OLEDs). The maximum electro luminescence (EL) and current density at 100 $cd/m^2$ were 2500 $cd/m^{2}$ and 2 $mA/m^{2}$, respectively, and the external quantum efficiency of the OLEDs was found to be 2.0 %.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2002.05a
• /
• pp.68-68
• /
• 2002

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.212-213
• /
• 2004

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.117-117
• /
• 2000

높은 광학적 투과성과 전기전도성을 갖는 ITO film은 solar cell같은 optoelectronic device나 휴대용 소형 TV, flat panel display 등의 투명전극으로 그 응용 분야가 광범위하여 많은 연구가 수행되어져 왔다. 기판으로서 유리를 사용할 때 생기는 활용범위 제한을 극복하고자 최근 유기물 위에 증착이 가능한 저온 증착방법에 대한 연구가 활발히 이루어지고 있다. 그 가운데 이온빔과 같은 energetic한 beam을 이용한 박막의 제조는 기판을 플라즈마 발생지역으로부터 분리시켜 이온빔의 flux 및 에너지, 입사각 등의 자유로운 조절을 통해 상온에서도 우수한 성질의 박막형성 가능성이 제시되어 지고 있다. ITO박막을 형성하는 방법 중 스프레이법이나 CVD법과 같은 화학적 증착방법은 증착시 350-50$0^{\circ}C$의 고온이 필요하고 현재 가장 많이 응용되어 지고 있는 sputter법은 15$0^{\circ}C$정도의 가열이 필요하므로 앞으로 응용가능성이 매우 커서 많은 연구가 진행중인 플라스틱과 아크릴 같은 flexible 한 기판위 증착에 적용이 불가능하다. 본 실험에서는 IBAD(Ion Beam Assisted Deposition)법을 이용하여 저온 ITO film을 유리와 유기막위에 증착하는 연구를 수행하였다. 유기막위에 증착된 ITO는 보다 가볍고 충격에 강하고 유리에 못지 않은 투과성을 가지고 있으나 현재 film의 quality 향상에 대한 요구가 증대되어 지고 있는 실정이다. 따라서, 본 실험에서는 dual oxygen ion gun의 조건변화에 따른 ITO film의 특성변화를 관찰하였다. 고정된 증？율에 한 개 ion gun에 ion flux를 고정시킨 후 또 다른 ion gun에서 발생하는 oxygen radical의 영향을 조사하였으며 oxygen radical의 rf power에 따른 변화는 OES(Optical emission spectroscopy)를 사용하였다. 너무 적은 oxygen ion beam flux나 oxygen radical은 film의 전도도 및 투과도를 저하시켰고 반면 너무 과도한 flux의 증가 시는 전도도는 감소하였고 투과도는 증가하는 경향을 보였다. 기판에 도달하는 oxygen ion flux는 faraday cup을 이용하여 측정하였으며 증착된 ITO film은 XPS, UV-spectrometer, 4-point probe를 이용하여 분석하였다.

• Korean Journal of Materials Research
• /
• v.23 no.3
• /
• pp.194-198
• /
• 2013

In this paper, we studied a p-type reflector based on indium tin oxide (ITO) for vertical-type ultraviolet light-emitting diodes (UV LEDs). We investigated the reflectance properties with different deposition methods. An ITO layer with a thickness of 50 nm was deposited by two different methods, sputtering and e-beam evaporation. From the measurement of the optical reflection, we obtained 70% reflectance at a wavelength of 382 nm by means of sputtering, while only 30% reflectance resulted when using the e-beam evaporation method. Also, the light output power of a $1mm{\times}1mm$ vertical chip created with the sputtering method recorded a twofold increase over a chip created with e-beam evaporation method. From the measurement of the root mean square (RMS), we obtained a RMS value 1.3 nm for the ITO layer using the sputtering method, while this value was 5.6 nm for the ITO layer when using the e-beam evaporation method. These decreases in the reflectance and light output power when using the e-beam evaporation method are thought to stem from the rough surface morphology of the ITO layer, which leads to diffused reflection and the absorption of light. However, the turn-on voltage and operation voltage of the two samples showed identical results of 2.42 V and 3.5 V, respectively. Given these results, we conclude that the two ITO layers created by different deposition methods showed no differences in the electric properties of the ohmic contact and series resistance.

• Korean Journal of Materials Research
• /
• v.9 no.11
• /
• pp.1055-1061
• /
• 1999

Indium Tin Oxide (ITO) films were fabricated by vacuum deposition technique and their microwave shielding properties were investigated for the application to the transparent shield material. The vacuum coating was conducted in a RF co-sputtering machine. The film composition and structure associated with the sputtering conditions (argon and oxygen pressure. substrate temperature. RF input power) were investigated for the attainment of high electrical conductivity and good transparency. The electrical conductivity of IT0 films fabricated under the optimum deposition conditions (substrate temperature : $300^{\circ}C$. Ar flow rate : 20 sccm, Oxygen flow rate : 10 sccm, In/Sn input power : 50/30 W) showed 5.6$\times10^4$mho/m. The optical transparency is also considerably good. The microwave shielding properties including the dominant shielding mechanism are investigated from the electrical conductivity, thickness and skin depth of the ITO films. The total shielding effectiveness is then estimated to be 26 dB, which provides a suggestion that the IT0 films can be effectively used as the transparent shield material.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.59-66
• /
• 2020

In this study, the characteristics of ITO thin film was investigated to finding a low cost and highly transparent electrodes for display of mobile communication devices. The ITO film was deposited by DC magnetron sputter. The experimental conditions were changed as follows: 1. ambient pressure changed 1 to 3 mTorr with 1mTorr step, 2. bias electric voltage changed with 10V step. The chamber was pumped out by rotary pump until 10^-3Torr then the diffusion pump was used to lower the pressure of 10^-6Torr. The results shows us the film growth was obvious when the bias voltage was larger than 300V, but the overall thickness tendency was existed: the more voltage is the thicker thickness. At 330V bias voltage condition, the deposition rate was the largest and apparent grain was showed.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1325-1327
• /
• 2002

$ITO_{(n)}/Si_{(p)}$ solar cell was fabricated by vaccum deposition method under the resistance heating with substrate temperature kept about 200[$^{\circ}C$] and than their properties are investigated. The cell charateristics can be improved by annealing but are deteriorated at temperature above 650[$^{\circ}C$] for longer than 15[min].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.141-141
• /
• 2009

본 실험에서는 비평형 마그네트론 스퍼터링 (Unbalanced Magnetron Sputtering, UBMS)을 이용하여 제작된 ITO 박막의 전기적, 광학적, 구조적인 특성들에서 기판온도와 자장 변화의 영향에 대해 연구하였다.