• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.6-13
• /
• 2006

Tin doped indium oxide(ITO) and Al doped zinc oxide(ZnO:Al) films, which are widely used as a transparent conductor in optoelectronic devices, were prepared by using the capacitively coupled DC magnetron sputtering method. ITO and ZnO:Al films with the optimum growth conditions showed each resistivity of $1.67{\times}10^{-3}[{\Omega}-cm],\;2.2{\times}10^{-3}[{\Omega}-cm]$ and transmittance of 89.61[%], 90.88[%] in the wavelength range of the visible spectrum. The two types of 5 inch-PDP cells with ZnO:Al and ITO transparent electrodes were made under the same manufacturing conditions. The PDP cell with ZnO:Al film was optimally operated in the mixing gas rate of Ne(base)-Xe(8[%]), and at gas pressure of 400[Torr]. It also shows the average measured brightness of $836[cd/m^2]$ at voltage range of $200{\sim}300$[V]. Luminous efficiency, one of the key parameter for high brightness and low power consumption, ranges from 1.2 to 1.6[lm/W] with increasing frequency of ac power supplier from 10 to 50[Khz]. The brightness and luminous efficiency are lower than those with ITO electrode by about 10[%]. However, these values are considered to be enough for the normal operation of PDP TV.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.439-439
• /
• 2012

ZnO 나노로드는 큰 밴드갭 에너지(~3.37 eV)와 60 meV의 높은 엑시톤 결합 에너지(exciton binding energy)를 갖고 있으며, 우수한 전기적, 광학적 특성을 지닌 1차원 나노구조의 금속산화물로서 태양전지 및 광전소자 널리 응용되고 있다. 이러한 ZnO 나노로드를 성장하는 방법 중에 전기화학증착법(electrochemical deposition method)은 전도성 물질위에 증착된 시드층(seed layer)을 성장용액에 담그어 전압을 인가하여 만들기 때문에 기존의 수열합성법(hydrothermal method), 졸-겔 법(sol-gel method)보다 비교적 간단한 공정과정으로 저온에서 빠르게 물질을 성장시킬 수 있는 장점이 있다. 한편, 디스플레이 산업에서 ITO (indium tin oxide)는 투명 전도성 산화물(transparent conductive oxide)로써 가시광 파장영역에서 높은 투과율과 전도성을 가지며, 액정디스플레이, LED (Light emitting diode), 태양전지 등의 다양한 소자에 투명전극 재료로 쓰이고 있다. 또한 최근 ITO를 유연한 PET (polyethylene terephthalate) 기판 위에 증착은 얇고, 가볍고, 휘어지기 쉬워 휴대하기 편하기 때문에 차세대 광전자소자 응용에 가능성이 크다. 본 연구에서는 ZnO 나노로드를 ITO/PET 기판위에 전기화학증착법으로 성장하여, 구조적 및 광학적 특성을 분석하였다. 시드층을 형성하기 위해 RF 마그네트론 스퍼터를 이용하여 ~20 nm 두께의 ZnO 박막을 증착시킨 후, zinc nitrate와 hexamethylenetetramine이 포함된 수용액에 시료를 담그어 전압을 인가하였다. 용액의 농도와 인가전압을 조절하여 여러 가지 성장조건에 대한 ZnO 나노로드의 구조적, 광학적 특성을 비교하였다. 성장된 시료의 형태와 결정성을 조사하기 위해, field-emission scanning electron microscope (FE-SEM), X-ray diffraction (XRD)을 사용하였으며, UV-vis-NIS spectrophotometer, photoluminescence (PL) 측정장비를 사용하여 광학적 특성을 분석하였다.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2689-2693
• /
• 2012

Single-walled carbon nanotubes (SWNTs) and $C_{60}$-encapsulated SWNTs ($C_{60}@SWNTs$) are introduced to Ru-sensitized photoelectrochemical cells (PECs), and photocurrents are compared between two cells, i.e., an $RuL_2(NCS)_2$/DAPV/SWNTs/ITO cell and an $RuL_2(NCS)_2$/DAPV/$C_{60}@SWNTs$/ITO cell. [L = 2,2'-bipyridine-4,4'-dicarboxylic acid, DAPV = di-(3-aminopropyl)-viologen, and ITO = indium-tin oxide] The photocurrents are increased by 70.6% in the presence of $C_{60}@SWNTs$. To explain the photocurrent increase, the reverse-field emission method is used, i.e., $RuL_2(NCS)_2$/DAPV/SWNTs/ITO cell (or $RuL_2(NCS)_2$/DAPV/$C_{60}@SWNTs$/ITO cell) as an anode and a counter electrode Pt as a cathode in the external electric field. The improved field emission properties, i.e., ${\beta}$ (field enhancement factor) and emission currents in the reverse-field emission with $C_{60}@SWNTs$ indicate the enhancement of the PEC electric field, which implies the improvement of the electron transfer rate along with the reduced charge recombination in the cell.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.35-38
• /
• 2003

Polymer light emitting diode (PLED) with an ITO/MEH-PPV/Al structure were prepared by spin coating method on the ITO (indium tin oxide)/glass substrates, using poly(2-methoxy-5-(2-ethylhexoxy)-1,4-phenylenevinylene (MEH-PPV) as the light emitting material. The dependence of heat treatment on the electrical and optical properties for the prepared PLED samples were investigated. The luminance decreased greatly from 630 cd/$\m^2$ to 280 cd/$\m^2$ at 10V input voltage as the heating temperature increased from $65^{\circ}C$ to $170^{\circ}C$. In addition, the luminance efficiency was found to be about 2 lm/W for the sample heat treated at $65^{\circ}C$. These results may be related to the interface roughness and/or the formation of an insulation layer, which is caused by the reaction between electrode and MEH-PPV organic luminescent film layer.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.485-485
• /
• 2012

유기발광소자는 고휘도, 넓은 시야각, 빠른 응답속도, 높은 색재현성, 좋은 유연성의 소자특성 때문에 디스플레이 제품에 많이 응용되고 연구가 활발하게 진행되고 있다. 최근에 저소비전력, 고휘도, 소형화 및 장수명의 장점을 가진 유기발광소자의 상용화가 진행되면서 차세대 디스플레이소자로서 관심을 끌게 되었다. 고분자 유기발광소자는 저분자 유기발광소자에 비해 용액 공정법으로 박막을 형성할 수 있어 제조 비용이 적게 들며 대면적 디스플레이를 제작하는데 유리하기 때문에 많은 연구가 진행되고 있다. 고분자 유기발광소자에서 저전력 소자를 위한 저전압 구동 및 전력 효율을 향상시키기 위한 연구는 대단히 중요하다. 본 연구에서는 고분자 유기발광소자의 구동 전압을 낮추기 위해서 그래핀 정공 주입층을 삽입한 고분자 유기발광소자를 화학적 진공 증착법과 용액 공정을 사용하여 제작하였다. 그래핀 정공 주입층을 삽입한 고분자 유기발광소자는 Indium-tin-oxide(ITO) 투명 전극/그래핀 정공주입층/poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT: PSS)/poly[2-methoxy, 5-(2'-ethyl-hexyloxy)-p-phenylenevinylene] (MEH-PPV) 층/lithium quinolate (Liq)/aluminium (Al) 전극의 구조를 가진다. 그래핀 정공주입층을 삽입한 고분자 유기발광소자에서 향상된 정공 주입능력을 통해 구동전압을 낮아지는 현상을 분석하기 위해서 전기적 및 광학적 특성을 조사하였다. 그래핀 정공주입층의 광학적 특성을 분석하기 위해서 빛의 투과도 측정을 한 결과 90% 이상의 값을 얻었다. 그래핀 정공 주입층이 소자에 미치는 영향을 조사하기 위하여 ITO/PEDOT:PSS소자와 ITO/그래핀 층/PEDOT:PSS 소자를 각각 제작하여 원자힘 현미경 측정을 하였다. 그래핀박막층을 삽입할 경우, 그래핀박막층을 삽입하지 않았을 때보다 표면 거칠기가 감소하는 것을 알 수 있었다. 이는 산성을 띠는 PEDOT:PSS 용액이 ITO 투명 전극을 손상시키는 것을 방지하고, 표면 거칠기를 감소시켜 누설 전류를 낮출 수 있다는 사실을 보여준다. 또한, 그래핀 박막은 높은 전기 전도도를 가지기 때문에 그래핀 정공주입층을 삽입하였을 때, 높은 전류 밀도 및 발광 휘도와 더 낮은 구동 전압을 확인할 수 있었다. 이러한 결과는 ITO와 PEDOT:PSS의 계면에서의 전공의 주입 능력을 그래핀박막층이 향상시켜 저전압, 고효율 소자를 제작할 수 있다는 것을 보여준다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1514-1519
• /
• 2009

We fabricated the GaNLED emitting 400 nm wavelength and improved the optical extraction efficiency by making surface patterns on n-GaN layer and ITO layer above p-GaN. In addition, the light reflection metal under the n and p pad is made and the light reflection metal is installed on the backside of the chip. The light extraction efficiency is increased by 20 % with texturing n-GaN layer and 18% with texturing ITO layer at 20 mA. Compared to planar-surface LED, the light extraction efficiency for surface texturing both n-GaN and ITO is increased by 32% at 20mA.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.335-335
• /
• 2014

Over the past several years, transparent conducting oxides have been extensively studied in order to replace indium tin oxide (ITO). Here we report on fluorine doped zinc tin oxide (FZTO) films deposited on glass substrates by radio-frequency (RF) magnetron sputtering using a 30 wt% ZnO with 70 wt% SnO2 ceramic targets. The F-doping was carried out by introducing a mixed gas of pure Ar, CF4, and O2 forming gas into the sputtering chamber while sputtering ZTO target. Annealing temperature affects the structural, electrical and optical properties of FZTO thin films. All the as-deposited FZTO films grown at room temperature are found to be amorphous because of the immiscibility of SnO2 and ZnO. Even after the as-deposited FZTO films were annealed from $300{\sim}500^{\circ}C$, there were no significant changes. However, when the sample is annealed temperature up to $600^{\circ}C$, two distinct diffraction peaks appear in XRD spectra at $2{\Theta}=34.0^{\circ}$ and $52.02^{\circ}$, respectively, which correspond to the (101) and (211) planes of rutile phase SnO2. FZTO thin film annealed at $600^{\circ}C$ resulted in decrease of resistivity $5.47{\times}10^{-3}{\Omega}cm$, carrier concentration ~1019 cm-3, mobility~20 cm2 V-1s-1 and increase of optical band gap from 3.41 to 3.60 eV with increasing the annealing temperatures and well explained by Burstein-Moss effect. Change of work function with the annealing temperature was obtained by ultraviolet photoemission spectroscopy. The increase of annealing temperature leads to increase of work function from ${\phi}=3.80eV$ (as-deposited FZTO) to ${\phi}=4.10eV$ ($600^{\circ}C$ annealed FZTO) which are quite smaller than 4.62 eV for Al-ZnO and 4.74 eV for SnO2. Through X-ray photoelectron spectroscopy, incorporation of F atoms was found at around the binding energy of 684.28 eV in the as-deposited and annealed FZTO up to 400oC, but can't be observed in the annealed FZTO at 500oC. This result indicates that F atoms in FZTO films are loosely bound or probably located in the interstitial sites instead of substitutional sites and thus easily diffused into the vacuum from the films by thermal annealing. The optical transmittance of FZTO films was higher than 80% in all specimens and 2-3% higher than ZTO films. FZTO is a possible potential transparent conducting oxide (TCO) alternative for application in optoelectronics.

• Journal of the Korean Society of Radiology
• /
• v.4 no.1
• /
• pp.5-9
• /
• 2010

In recent, a digital x-ray detector attracted worldwide attention and there are many studies to commercialize. There are two methods in digital x-ray detector. This method is an Indirect method and Direct method. This study is to see the differences between the digital x-ray detector based on a-Se used in the existing indirect conversion method and an x-ray conversion material that has better SNR(Signal-to-noise ratio) and property than the a-Se. To solve the problem that is difficult to make a large area film using Screen-Print method, we used a Screen-Print method. In this study, we used a polyclystal $HgI_2$ as x-ray conversion material and a sample thickness is $150{\mu}m$ and an area is $3cm{\times}3cm$. ITO(Indium-Tin-Oxide) electrode was used as top electrode using a Magnetron Sputtering System and each area is $3cm{\times}3cm$, $2cm{\times}2cm$ and $1cm{\times}1cm$ and then we evaluated darkcurrent, sensitivity and SNR of the $HgI_2$ film are measured, then we evaluated the electrical properties. And we used a current integration mode when I-V test. This experiment shows that the sensitivity increases in accordance with the area of the electrode but the SNR is decreased because of the high darkcurrent. Through fabricating of various thicknesses and optimal electrodes, we will optimize SNR in the future work.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.377-377
• /
• 2011

Organic solar cells (OSCs) with low cost have been studied to apply on flexible substrate by solution process in low temperature [1]. In previous researches, conventional organic solar cell was composed of metal oxide anode, buffer layer such as PEDOT:PSS, photoactive layer, and metal cathode with low work function. In this structure, indium tin oxide (ITO) and Al was generally used as metal oxide anode and metal cathode, respectively. However, they showed poor reliability, because PEDOT:PSS was sensitive to moisture and air, and the low work function metal cathode was easily oxidized to air, resulting in decreased efficiency in half per day [2]. Inverted organic solar cells (IOSCs) using high work function metal and buffer layer replacing the PEDOT:PSS have focused as a solution in conventional organic solar cell. On the contrary to conventional OSCs, ZnO and TiO2 are required to be used as a buffer layer, since the ITO in IOSC is used as cathode to collect electrons and block holes. The ZnO is expected to be excellent electron transport layer (ETL), because the ZnO has the advantages of high electron mobility, stability in air, easy fabrication at room temperature, and UV absorption. In this study, the IOSCs based on poly [N-900-hepta-decanyl-2,7-carbazole-alt-5,5-(40,70-di-2-thienyl-20,10,30-benzothiadiazole)] (PCDTBT) : [6,6]-phenyl C71 butyric acid methyl ester (PC70BM) were fabricated with the ZnO electron-transport layer and MoO3 hole-transport layer. Thickness of the ZnO for electron-transport layer was controlled by rotation speed in spin-coating. The PCDTBT and PC70BM were mixed with a ratio of 1:2 as an active layer. As a result, the highest efficiency of 2.53% was achieved.

• Journal of the Microelectronics and Packaging Society
• /
• v.13 no.1 s.38
• /
• pp.51-55
• /
• 2006

The green emitting high performance OLEDs using the $Alq_3$-C545T fluorescent system have been fabricated and characterized. In the device fabrication, 2-TNATA [4,4',4'-tris(2-naphthylphenyl-phenylamino)-triphenylamine] as a hole injection material and NPB [N,N'-bis(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine] as a hole transport material were deposited on the ITO(indium thin oxide)/glass substrate by vacuum evaporation. And then, green color emission layer was deposited using $Alq_3$ as a host material and C-545T[10-(2-benzothiazolyl)-1,1,7,7- tetramethyl-2,3,6,7-tetrahydro-1H,5H,11H-[1]/benzopyrano[6,7,8-ij]-quinolizin-11-one] as a dopant. Finally, small molecule OLEDs with structure of ITO/2-TNATA/NPB/$Alq_3$:C545T/$Alq_3$/LiF/Al were obtained by in-situ deposition of $Alq_3$, LiF and Al as the electron transport material, electron injection material and cathode, respectively. Green OLEDs fabricated in our experiments showed the color coordinate of CIE(0.29, 0.65) and the maximum power efficiency of 7.3 lm/W at 12 V with the peak emission wavelength of 521 nm.