• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.3
• /
• pp.290-297
• /
• 2016

The absorbent loss due to degradation in $CO_2$ capture process using aqueous alkanol amine solution has adverse effect on the economics of overall process. The degradation causes absorbent loss, equipment corrosion, foaming, adhesive material producing and viscosity increase in operation. In this study, the degradation characteristics of $CO_2$ capture process using MEA (monoehtanolamine) under various conditions such as $O_2$ partial pressure, $CO_2$ loading and absorbent temperature. The effects of iron, which generated from the equipment corrosion, on absorbent degradation were studied using $Fe_2SO_4$ containing MEA solution. The produced gases were analyzed by FT-IR(Fourier Transform Infrared Spectrophotometer) and the specifically measured $NH_3$ concentration was used as a degradation degree of aqueous MEA solution. The experiments showed that the higher $CO_2$ loadings (${\alpha}$), $O_2$ fraction ($y_{O2}$) and reaction temperature enhanced the more degradation of aqueous MEA solution. Comparing other operation parameters, the reaction temperature most affected on the degradation. Therefore, it could be concluded that the above parameters affects on degradation should be considered for the selections of $CO_2$ absorbent and operating conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.194-200
• /
• 2020

Perylene bisimide derivatives are developed for red organic phosphor because of their advantages, such as excellent luminous efficiency and high thermal stability. Despite these advantages, they have poor solubility characteristics in organic solvents and short emission wavelength as red organic phosphor for hybrid light-emitting diodes (LEDs). In this study, we prepared terrylene bisimide using a coupling reaction and swallow-tail imide group, which has excellent solubility. The structures and properties of swallow-tail terrylene bisimide (9C) were analyzed using ¹H-nuclear magnetic resonance (¹H-NMR), Fourier-transform infrared (FT-IR), UV/Vis spectroscopy, and thermal gravimetric analysis (TGA). The maximum absorption wavelength of (9C) in the UV/Vis spectrum was 647 nm, and the maximum emission wavelength was 676 nm. In the TGA, (9C) demonstrated good thermal stability with less than 5 wt% weight loss up to 415℃. In the solubility test, (9C) has a good solubility of more than 5 wt% in chloroform and dichloromethane. When the compounds (9C) were mixed with PMMA (polymethly methacrylate), the films showed peaks at 680 nm in the PL spectra. The results verify the suitability of (9C) as a red organic phosphor for hybrid LEDs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.56-59
• /
• 2004

HgTe and HgTe/CdTe core-shell structured nanocrystals(NCs) were synthesized in aqueous solution by colloidal method. HgTe and HgTe/CdTe NCs structure showed very similar XRD patterns because of the same lattice constant and crystal structure of both samples. The absorption and photoluminescence(PL) spectrum of the synthesized HgTe NCs revealed the strong exitonic peak in the IR region. The PL spectrum of HgTe/CdTe NCs have the intense peak in about 700nm shorter than that of HgTe by 400nm. The photocurrent measurement of colloidal NCs are performed using He-Ne laser for light source. The photocurrent of HgTe NCs shows the instant increased current response to light, but HgTe/CdTe NCs revealed a decreased current when lighted to the sample. In the vacuum condition, it shows reverse result that current increased under the illumination of light and it is thought that the molecules like the hydro-oxygen gas in the air give an important effect on the current mechanism.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.292.2-292.2
• /
• 2013

Graphene, a two-dimensional graphite material consisting of sp2-hybridized carbons. The properties of graphene such as extremely high carrier mobility, high thermal conductivity, low resistivity, large specific make it a promising materail of divices and material. Typically, poly (methyl methacrylate) (PMMA) is used when graphene transfer to other substrates. To remove PMMA on graphene, people used to dip the graphene into the acetone. However, it is known that the remove of PMMA on the graphene is difficult to completely using the acetone. Therefore, to remove the PMMA on the graphene surface, many research groups have employed various methods such as the thermal treatment, photothermal method, and other solvent. Nevertheless, a part of PMMA still remain on graphene surface. Usually, to observe the residual PMMA on graphene surface, topography of graphene surface scanned by atomic force microscopy is used. However, in that case, we can not distinguish PMMA and other particles. In this study, to confirm the residual PMMA on graphene surface, we employed novel measurement technique which is available to distinguish PMMA and other particles by means of photothermal effect.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.130.1-130.1
• /
• 2013

We made attempts to improve photocatalytic activity of $TiO_2$ nanoparticles under visible light exposure by combining two additional treatments. N-doping of $TiO_2$ by ammonia gas treatment at $600^{\circ}C$ increased absorbance of visible light. By coating thin film of polydimethylsiloxane (PDMS), and subsequent vacuum-annealing at $800^{\circ}C$, $TiO_2$, became more hydrophilic, thereby enhancing photocatalytic activity of $TiO_2$. Four types of $TiO_2$ samples were prepared, bare-$TiO_2$, hydrophilic-modified $TiO_2$ ($h-PDMS/TiO_2$), N-doped $TiO_2$ ($N/TiO_2$) and hydrophilic-modified and N-doped $TiO_2$ ($h-PDMS/N/TiO_2$). Adsorption capability was evaluated under dark condition and photocatalytic activity of $TiO_2$ was evaluated by photodegradation of MB under blue LED (400 nm< ${\lambda}$) irradiation. N-doping on $TiO_2$ was characterized using XPS and hydrophilic modification of $TiO_2$ surface was analyzed by FT-IR spectrometer. It was found that N-doping and hydrophilic modification both had positive effect on enhancing adsorption capability and photocatalytic activity of $TiO_2$ at the same time. Particularly, N-doping enhanced visible light absorption of $TiO_2$, whereas hydrophilic surface modification increased MB adsorption capacity. By combining these two strategies, photocatalytic acitivity under visible light irradiation became the sum of individual effects of N-doping and hydrophilic modification.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.5
• /
• pp.271-281
• /
• 1992

Amorphous hydrogenated silicon carbide(a-Si1-xCx : H) films have been prepared by the rf sputtering using a silicon target in a gas mixture of Argon and methane with varying methane gas flow rate(fCH) in the range of 1.5 to 3.5 sccm at constant Argon flow rate of 30sccm and rf power in the range of 3 to 6 W/$\textrm{cm}^2$. The effects of methane flow rate and rf power on the structure and optical properties of a-Si1-xCx : H films have been analysed by measuring both the IR absorption spectrum and the UV transmittance for the films. With increasing the methane flow rate, the optical band gap(Eg) of a-Si1-xCx : H films increases gradually from 1.6eV to the maximum value of 2.42eV at rf power of 4 W/$\textrm{cm}^2$, which is due to an increases in C/Si ratio in the films by an significant increase in the number of C-Hn bonds. As the rf power increases, the number of Si-C and Si-Hn bonds increases rapidly with simultaneous reduction in the number of C-Hn bonds, which is associated with an increase in both degree of methane decomposition and sputtering of silicon. The effects of rf power on the Eg of films are considerably influenced by the methane flow rate. At low methane flow rate, the Eg of films decreased from 2.3eV to 1.8eV with the rf power. On the other hand, at high methane flow rate, that of films increased slowly to 2.4eV.

• Journal of dental hygiene science
• /
• v.9 no.2
• /
• pp.189-195
• /
• 2009

Two diketones, 1,2-phenylpropanedione (PD) and diacetyl (DA) were investigated as new visible light photosensitizers for dental composite resin of bis-GMA in order to improve the photopolymerization effect. The photopolymerization efficiency of bis-GMA composite resin containing PD and DA was studied by IR absorption spectroscopy. And the results were compared with that of camphorquinone (CQ). Relative photopolymerization efficiency of the photosensitizers increased in the order of DA < CQ < PD. Thus. PO is a new visible light photosensitizer for dental composite resin with higher photopolymerization efficiency than that of CQ.

• Journal of Radiation Protection and Research
• /
• v.3 no.1
• /
• pp.23-28
• /
• 1978

In order to investigate corelation between contents of dioctylphthalate in polyvinylchloride blent dibutyl tin dilaulate with dibutyl tin maleate as stabilizer and the behaviors of radiation resistance as well as electrical conductivity on irradiated specimens, several observations were carried out. A characteristic peak observed in the range of $1,540-1,640cm^{-1}$ on infrared spectra shows such a sensitive response to radiation as the intensity decreases with increasing doses and that this tendency strongly depressed in the presence of plasticizer. It is seemingly attributed for origin of the peak to the existence of RCOO- ion resulting from dissociation of stabilizere, further the depressive effect of decreasing peak intensity influenced by radiation seems to be caused by resonance absorption in benzen ring being a consistituent of plasticizer. It is also suggestive to be use the peak behavior influenced by radiation as a criterion for the evaluation of radiation resistance of PVC. Further the results obtained from electrical conductivity measurement also exhibit reasonable characteristics explainable with views used for the interpretation of the peak behavior mentioned previousely.

• Bulletin of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.130-137
• /
• 1991

The following new cryptand 221 complexes of lanthanides(Ⅲ) and dioxouranium(Ⅵ) nitrate have been synthesized: $(Ln(C_{16}H_{32}N_2O_5)(H_2O)_2(NO_3)_3\ and \((UO_2)_2(C_{16}H_{32}N_2O_5)(H_2O)_4(NO_3)_4$. These complexes have been identified by elemental analysis, moisture titration, conductivity measurements and various spectroscopic techniques. The proton and carbon-13 NMR as well as calorimetric measurements were used to study the interaction of cryptand 221 with La(Ⅲ), Pr(Ⅲ ), Ho(Ⅲ) and $UO_2(Ⅱ)$ ions in nonaqueous solvents. The bands of metal-oxygen atoms, metal-nitrogen atoms and O-U-O in the IR spectra shift upon complexation to lower frequencies, and the vibrational spectra ({\delta}NMN$) of metal-amide complexes in the crystalline state exhibit lattice vibrations below 300 $cm^{-1}$. The NMR spectra of the lanthanides(Ⅲ) and dioxouranium(Ⅵ) nitrate complexes in nonaqueous solvents are quite different, indicating that the ligand exists in different conformation, and also the $^1H$ and $^{13}C-NMR$ studies indicated that the nitrogen atom of the ring has greater affinity to metal ions than does the oxygen atom, and the planalities of the ring are lost by complexation with metal ions. Calorimetric measurements show that cryptand 221 forms more stable complexes with $La^{3+}$ and $Pr^{3+}$ ions than with $UO^{22+}$ ion, and $La^{3+}/Pr^{3+}$ and $UO^{22+}/Pr^{3+}$ selectivity depends on the solvents. These changes on the stabilities are dependent on the basicity of the ligand and the size of the metal ions. The absorption band (230-260 nm) of the complex which arises from the direct interaction of macrocyclic donor atoms with the metal ion is due to n-{\delta}*$ transition and also that (640-675 nm) of $UO^{22+}$-cryptand 221 complex, which arises from interaction between two-dioxouranium(Ⅵ) ions in being out of cavity of the ligand ring is due to d-d* transition.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.3
• /
• pp.19-23
• /
• 2009

We have studied dielectric characteristics of low-k interlayer dielectric materials was fabricated by plasma enhanced chemical vapor deposition (PECVD). BTMSM precursor was introduced with the flow rates from 24 sccm to 32 sccm by 2 sccm step in the constant flow rate of 60 sccm $O_2$. Then, SiOCH thin film deposited at room temperature was annealed at temperature of $400^{\circ}C$ and $500^{\circ}C$ for 30 minutes in vacuum. The vibrational groups of SiOCH thin films were analyzed by FT/IR absorption lines, and the dielectric constant of the low-k SiOCH thin films were obtained by measuring C-V characteristic curves. With the result that FTIR analysis, as BTMSM flow rate increase, relative carbon content of SiOCH thin film increased from 29.5% to 32.2%, and increased by 32.8% in 26 sccm specimen after $500^{\circ}C$ annealing. Dielectric constant was lowest by 2.32 in 26 sccm specimen, and decreased more by 2.05 after $500^{\circ}C$ annealing. Also, leakage current is lowest by $8.7{\times}10^{-9}A/cm^2$ in this specimen. In the result, shift phenomenon of chemical bond appeared in SiOCH thin film that BTMSM flow rate is deposited by 26 sccms, and relative carbon content was highest in this specimen and dielectric constant also was lowest value