• 한국안전학회지
• /
• 제26권2호
• /
• pp.1-5
• /
• 2011

In order to evaluate fatigue endurance for an ultra-light weight inline skate frame, FEM analysis was performed. Tensile properties and a S-N curve were determined through tensile and fatigue tests on a modified Al-7075+$S_c$ alloy. The yield and ultimate tensile strengths were 553.3 MPa and 705.5 MPa, respectively. The fatigue endurance limit of this alloy was 201.2 MPa. For evaluating the fatigue endurance of the inline skate frame, the S-N data were compared with the stress analysis results through FEM analysis of the frame. The maximum Von-Mises stress of the frame was determined 106 MPa through FEM analysis of the frame, assuming that the rider weight is 75 Kg. Conclusively, on the basis of fatigue limit, the inline skate frame has a safety factor of approximately 2.0.

• 한국CDE학회논문집
• /
• 제10권1호
• /
• pp.17-26
• /
• 2005

In-line skate generally consists of four major parts: boot, frame, bearing and wheel, and the most important part among those for necessary functionality is the frame. It is the most expensive, and it also makes a decisive role in practical race skating. The functional behavior of a frame is greatly affected by external dynamic forces as well as the static weight of a skater. We are proposing a new inline speed-skating frame design that has been improved in structural strength and weight for providing optimum speed in $20\sim40km$ marathon skating.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.30-37
• /
• 1999

This paper represents the development of the brake system for the inline skate using bellows. The inline skate that is used at present has defects due to frequent impulse, which weakens the breaking force by damaging the parts. Therefore to solve these problems a break system for the inline skates using hydraulics is suggested. To solve the oil leakage problems, bellows is used. Also to prevent the breaks from not touching the ground when skating the bellows is placed at the heel, high as possible. To obtain fast response speed, the ratio of inner diameter of the bellows is changed so that with only a small displacement from the bellows the rubber pad attached to the bellows will touch the ground fast. The performance of the break system using bellows depends on the optimal design of the bellows. Therefore the parameters that changes the form of the bellows are tested and also the interaction between the forces are investigated. The performance of new model brake system with bellows and old model system with only a rubber pad without bellows was estimated through observation of braking posture.

• 대한기계학회논문집A
• /
• 제35권11호
• /
• pp.1507-1514
• /
• 2011

플라스틱 재료를 사용한 가공법 중에서 가장 보편적인 가공법이 사출성형이다. 오늘날에는 플라스틱 재료의 활용도는 지속적으로 증가하고 있으며, 신소재 등의 개발로 그 적용범위 또한 확대되고 있다. 인라인 스케이트는 4 가지 구성품으로 이루어진다. 그 4 가지 구성품은 부츠, 프레임, 휠, 브레이크로써 프레임이 가장 중요한 부품이다. 사출 재질에 변화에 따른 사출 성형성을 알아보았다. 런너와 게이트의 치수 변화에 따른 제품의 사출 성형성을 알아보았다. 본 연구에서는 Moldflow를 이용해서 사출성형 해석을 수행하였다. ANSYS를 이용해서 구조해석을 수행하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1228-1231
• /
• 2004

We analyzed the impulse on 24 sensors location under the foot using the Parotec system for the investigation of the relationship between the shoe type and the foot pathologies. Total 7 kinds of shoes, i.e. sport shoe, high heel shoes (5cm heel, 8cm heel, 13cm heel), platform shoe, inline skate, and heelys were evaluated for 20 normal subjects. Compared with the impulse distribution of the sport shoe, greater impulses were shown at the 1$^{st}$ phalange and the 1$^{st}$ metatarsal-phalangeal head in high-heel shoes, lateral tarsal bone and medial metatarsal bone in platform shoe, medial tarsal bone in inline-skate, and medial tarsal bone and 1st phalange in heelys shoe. The result of this study is expected to provide useful information about the relationship between the shoe type and the foot pathologies.ies.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.174-181
• /
• 2005

We analyzed the pressure, impulse on 24 sensors location under the foot using the Parolee system. Total 7 kinds of shoes, i.e. sport shoe, high heel shoes (5cm heel, 8cm heel, 13cm heel), platform shoe, inline skate, and heelys were evaluated for 20 normal subjects. Compared with those of sport shoe, greater pressure and impulse were shown on the 1 st phalange and the 1 st metatarsal head and greater impulse on the medial tarsal bone in high-heel shoes. Greater pressure and impulse were shown on medial metatarsal bone and the lateral tarsal bone in platform shoe. Greater impulse was shown on the medial tarsal bone in inline-skate. Heelys shoe showed smaller impulse on the central area of foot. The result of this study is expected to provide useful information about the relationship between the shoe type and the foot pathologies.

• 한국운동역학회지
• /
• 제15권2호
• /
• pp.11-20
• /
• 2005

This study has a purpose on contributing to apprehend safe and right way to stop to the inline skate beginners and to the instructors who teaches line skating on the basis for the result of the kinematical analysis on Heel brake stop movement of the inline skate, focusing on the displacement on COG, angle displacement of ankle joint, angle displacement of knee joint, angle displacement of hip joint, using a 3D image method by DLT. To achieve this goal, we analysed the kinematical factor of the 3 well-trained inline skating instructors and obtained the following results. 1. During the movement of heel-brake stop, when strong power was given to a stable and balanced stop and the lower limbs, if the physical centroid is lowered the stability increases, and if it is placed high from the base surface, as the stability decreases compared to the case of low physical centroid, we should make a stop by placing a physical centroid in the base surface and lowering the hight of physical centroid. 2. To make a stable and balanced stop and to provide a strong power to the lower limbs, it is advisable to make a stop by decreasing an angle displacement of ankle joint during a "down" movement. In case of the left ankle joint, in all events and phases the dorsiflexion angle showed a decrease. Nevertheless, in the case of the right ankle joint, the dorsiflexion angle shows an increase after a slight decrease. The dorsiflexion angle displacement of ankle joint can be diminished because of the brake pad of the rear axis frame of the right side inline skate by raising a toe, but cannot be more decreased if certain degree of an angle is made by a brake pad touching a ground surface. To provide a power to a brake pad, it is recommended to place a power by lowering a posture making the dorsiflexion angle of the left ankle joint relatively smaller than that of the right ankle. 3. To make a stable and balanced stop and to add a power to a brake pad, the power must be given to the lower limbs in lowering the hight of physical centroid. For this, it is recommended to make a down movement by decreasing the flexion angle of a knee joint and it is necessary to make a down movement by a regular decrease of the angle displacement of knee joint rather than a swift down movement in every event and phase. 4. The right angle displacement of hip joint is made by lowering vertically the hight of physical centroid as leaning slightly forward. If too narrow angle displacement of hip joint is made by leaning forward too much, the balance is lost during the stop by placing the center in front. To make a stable and balance stop and to place a strong power to the lower limbs, it is recommendable to make a narrow angle by lower the hip joint angle. However, excessive leaning of the upper body to make the angle too narrow, can cause an instable stop and loss of physical centroid. After this study, it is considered to assist the kinematical understanding during the heel brake stop movement of the inline skate, and, to present basic data in learning a method of stable and balanced stop for the inline skating beginners or for the inline skate instructors in the present situation of the complete absence of the study in inline skating.

• 한국운동역학회지
• /
• 제18권4호
• /
• pp.191-199
• /
• 2008

본 연구는 인라인 롤러스케이트의 가장 단거리인 300m 경기의 스타트 동작 분석을 함으로써, 지도자 및 선수들에게 스타트 기술에 대한 기초적이고 과학적인 자료를 제공하는데 목적이 있다. 연구의 대상은 국가 대표급 남자 선수 5명을 대상으로 3차원 영상분석을 통하여 인라인 롤러스케이트 T300m 종목의 스타트 동작을 분석하여 다음과 같은 결론을 도출하였다. 1)스타트 국면에서의 소요시간에서 P1에서의 시간이 절대적으로 영향을 미치고 있으므로 트레이닝을 통해 하지근력을 강화해야 한다. 2)스타트 속도를 증가시키기 위해서는 상체를 일으켜 세워 달리는 듯한 자세가 되어야 빠른 가속도를 얻을 수 있다. 3)상체의 전경각도는 출발시 뒤다리에 체중을 두고 반작용을 주는 자세에서 조금 세웠다가 첫발(오른발)이 진행되면서 착지할 때는 구부린 자세로 달리는 자세로 글라이딩 해야 한다.

• 한국운동역학회지
• /
• 제17권2호
• /
• pp.23-29
• /
• 2007

The purpose of this study was to examine if there are kinematic variables differences between national representative players (NRP) and non national representative players (NNRP) during 500 m inline skate starting motion. Four NRP and six NNRP were recruited for the study. Each subject executed starting motion five times on a $2{\times}12m$ start way in a gymnasium. Kinematic variables were analyzed by the three-dimensional motion analysis system (60Hz). It was hypothesized that there are difference in elapsed time and center of mass acceleration in starting phase between groups since starting phase has been considered important in sprinting. The results showed that the NRP had significantly shorter starting phase time than that of NNRP. 1) An elapsed time in phase P1 of NRP was shorter than that of NNRP, and excellent players have early started their first stroke. 2) Both NRP and NNRP have started at the same spot, and displacement of the center of gravity in starting posture of NRP group was at the front compared to NNRP group. 3) Average step lengths of NRP were longer than those of NNRP, and a step change of NRP was stabler compared to that of NNRP. 4) In a speed change of the center of gravity NRP showed comparatively high speed from P1 to P4.

• 한국운동역학회지
• /
• 제20권4호
• /
• pp.355-364
• /
• 2010

The purpose of this study was to investigate the kinematical analysis of T-stop motion by inline skate rolling speed. Six subjects were participated in the experiment(age: $35.0{\pm}3.3$ yrs, weight: $72.70{\pm}5.1\;kg$, height: $176.30{\pm}3.1\;cm$, career: $10.00{\pm}2.5$ yrs). The study method adopted 3-dimensional analysis and 2 cameras for filming to analyze the required displacement of center of mass, displacement of right and left hip joint, displacement of right and left knee joint, displacement of trunk tilt using by APAS. The results were as follows; In anterior-posterior displacement of COM, the faster rolling speed, the longer displacement at phase 2. In vertical displacement of COM, the faster rolling speed, the lower displacement. In medial-lateral displacement of COM, there was no significant on rolling speed. In angular displacement of right thigh segment, the faster rolling speed, the bigger displacement in X and Z axis. In angular displacement of left thigh segment, the faster rolling speed, the lower displacement in X axis. In angular displacement of right shank segment, the faster rolling speed, the bigger displacement in Z axis. In angular displacement of left shank segment, the faster rolling speed, the bigger displacement in X and Y axis. In angular displacement of trunk segment, the faster rolling speed, the bigger displacement in Z axis.