• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1126-1128
• /
• 1992

The object of this study is the design of 3 phase on-board inverter. The key point in the inverter design is the selection of switching device, and its performance effects that of total system. In this study, six-step square wave inverter was designed using IGBT ( Insulated Gate Bipolar Transistor ) which has the advantages of MOSFET and bipolar transistor as switching device. The condition of being small and light which is the one of requirements for on-board equipment was accomplished by using IGBT module and optimising the snubber circuit, and the reliablity was increased. It is confirmed that the designed inverter satisfies the required performance through the performance and environment test.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.12
• /
• pp.116-123
• /
• 2014

In case of power electronics, th power loss and EMI noise of IGBT is different depends on a adopting technology with the same power rating. To reduce the EMI noise, we could increase the resistance of gate. But in this case, the power loss of IGBT is increased, In this paper, we simulated the power loss of IGBT with the speed profile of elevator by the changing IGBT type, the voltage between gate and emitter, the resistance of gate in converter and inverter for elevator. To optimize the power electronics with the satisfied life time, It is necessary that we calculate the power loss and the rise of temperature in IGBT with the adopting technology type, the resistence of gate, the voltage between gate and emitter.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.576-580
• /
• 2000

This paper describes about the field test of IGBT VVVF inverter for the propulsion system. The 1650kV class IGBT VVVF inverter has been developed. Therefore the field test is performed in SMG 6 Line to confirm its the reliability and performance. The train consists of 4M4T and the electrical equipment for field test are as follows : VVVF inverter 4 sets 16 traction motors and 3 SIVs The propulsion system which have the excellent acceleration/deceleration and the jerk chracteristics as well as starting ability on slope are taken through the field test.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.335-339
• /
• 2001

The recent advancements in power electronic switching devices have enabled high frequency switching operation and have improved the performance of pulse-width modulated (PWM) inverters for driving induction motors. But, the insulation failures of stator winding have attracted much concern due to high dv/dt of IGBT PWM inverter. In this paper, the test results for evaluation on the stator winding insulation of low-voltage induction motors for IGBT PWM inverter applications are presented. The insulation characteristics are analyzed with partial discharge and dissipation factor tests. Also, insulation breakdown tests by switching pulse voltage are performed. An effective insulation technique to enhance the insulation strength is suggested from the test results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.4
• /
• pp.350-355
• /
• 2004

This paper deals with the design of a heat dissipation system, which consists of a heat source of power semiconductor devices, a heat sink ;md a fan for the forced air cooling. It suggests the method of appropriately dividing the whole heat transfer system into analytical subsystems and also presents the correspondent analytic or experimental design equations for the subsystems. The experimental results on the designed heat dissipation system for the 400kW IGBT inverter show less than 10［%］ error with respect to the design temperature and therefore verify the validity of the proposed analytical design method in the steady state.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.5
• /
• pp.521-528
• /
• 1992

this paper a new PAM-PWM Inverter using IGBT Is described. The output waveforms in the proposed PAM-PWM inverter are investigated both theoretiically and experimentally. The line-voltage waveform is composed of fundamental component and the sidebands of carrier frequency. The lower order harmonics are not included In the output waveform. As each inverter arm does not operate during two-thirds period, the heats, generated in the devices are reduced. That is the size of the inverter system can be minimized because of the reduction In the heat dissipating equipemnt.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.1
• /
• pp.43-49
• /
• 2005

The high rate of voltage rise (dv/dt) in motor terminals caused by high-frequency switching and impedance mismatches between inverter and motor are known as the primary causes of irregular voltage distributions and insulation breakdowns on stator windings in IGBT PWM inverter-driven induction motors. In this paper, voltage distributions in the stator windings of an induction motor driven by an IGBT PWM inverter are studied. To analyze the irregular voltages of stator windings, high frequency parameters are derived from the finite element (FE) analysis of stator slots. An equivalent circuit composed of distributed capacitances, inductance, and resistance is derived from these parameters. This equivalent circuit is then used for simulation in order to predict the voltage distributions among the turns and coils. The effects of various rising times in motor terminal voltages and cable lengths on the stator voltage distribution are also presented. For a comparison with simulations, an induction motor with taps in the stator turns was made and driven by a variable-rising time switching surge generator. The test results are shown.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.351-358
• /
• 2003

This paper describes distribution characteristics of switching surge voltage in stator windings of induction motor driven by IGBT PWM inverter. To analyze the voltage distribution between the turns and coils of stator winding, equivalent circuit model of induction motor including cable was proposed and high frequency parameter is computed by using finite-element method (FEM). From the electro-magnetic transient program (EMTP) simulation of the whole system for induction motor, feeder cable, and PWM inverter, the variable effect on rising time of the inverter, cable length, and switching frequency on the voltage distribution is also presented. In order to experiment, an induction motor, 380[V], 50[HP], with taps from one phase are built to consider the voltage distribution so that these results can be helpful when filter was designed to remove high dv/dt.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.17-20
• /
• 2002

In this paper voltage distribution in stator windings of induction motor driven by IGBT PWM inverter is studied. To analyze the irregular voltage of stator winding, equivalent circuit model of inverter-cable-motor was proposed and high frequency parameter is computed by using finite element method (FEM). Electro-magnetic transient program (EMTP) analysis of the whole system for induction motor and PWM inverter is proposed. Induction motor, 50[HP], and a switching surge generator was built to consider the voltage distribution. The results of EMTP analysis compared with experimental results.

• Proceedings of the KIPE Conference
• /
• 2008.10a
• /
• pp.61-63
• /
• 2008

An inverter with large capacity has been demanded at a factory automation and diffusion of the energy saving work. As the capacity of inverter is larger, the stary inductance has much influence on both the di/dt of IGBT current, and voltage stress across IGBT. Also, the life of the snubber capacitor may be shortened due to overheating of the snubber capacitor. In this paper, a planar busbar which consists of two layers is applied to N700-series inverter in order to minimize stray inductance. The voltage stress across IGBT is changed by both the DC busbar structure and the capacity of snubber capacitor.