• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.5
• /
• pp.1303-1315
• /
• 2012

In the draft of the IEEE 802.11s standard, a tree topology is established by the proactive tree-building mode of the Hybrid Wireless Mesh Protocol (HWMP). It is used for cases in which the root station (e.g., gateway) is an end point of the majority of the data connections. In the tree topology, the root or central stations (e.g., parent stations) are connected to the other stations (e.g., leaves) that are one level lower than the central station. Such mesh stations are likely to suffer heavily from contention in bottleneck links when the network has a high traffic load. Moreover, the dependence of the network on such stations is a point of vulnerability. A failure of the central station (e.g., a crash or simply going into sleep mode to save energy) can cripple the whole network in the tree topology. This causes performance degradation for end-to-end transmissions. In a connected mesh topology where the stations having two or more radio links between them are connected in such a way that if a failure subsists in any of the links, the other link could provide the redundancy to the network. We propose a scheme to utilize this characteristic by organizing the network into concentric tiers around the root mesh station. The tier structure facilitates path recovery and congestion control. The resulting mode is referred to as Tier-based Proactive Path Selection Mode (TPPSM). The performance of TPPSM is compared with the proactive tree mode of HWMP. Simulation results show that TPPSM has better performance.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.92-97
• /
• 2007

Switching mode amplifiers have been studied widely for use at microwave frequency range, and the class E amplifier which is a type of switching mode amplifier offers very high efficiency approaching 100%. In this paper, 2.4GHz microwave class E amplifier with 66% power added efficiency (PAE) and 17.6dBm output has been linearized for use at wireless LAN transmitter, and digital predistortion technique with look up table is applied. With -3dBm input power of wireless LAN, measured output spectrum can meet the required IEEE 802.11g standard spectrum mask, and the digital predistortion output spectrum has been improved by 5dB of ACPR at 20MHz offset from center frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.11B
• /
• pp.1272-1282
• /
• 2009

This paper consists of two parts: the protocol for tag-to-tag mesh network and the implementation of dual-radio RFID system. Recently, RFID has been adopted in ports or warehouse, being attached to containers and palettes for loading/unloading automation. However, the RFID system has encountered one problem - some tags cannot receive any command from reader intermittently due to signal interference by containers or field equipments (e. g. cranes and yard tractors). This area where reader signal cannot reach is called dead-zone. The proposed method for solving the dead-zone problem is as follows. A zone which can be communicated directly between readers and tags communicates in 433MHz frequency band in compliance with ISO/IEC 18000-7 standard. On the other hand, dead-zone communicates in 2.4GHz frequency band by using tag-to-tag mesh network in compliance with IEEE 802.15.4 standard. The proposed method can not only save much cost to install additional readers but also help resolve the dead-zone problem. Furthermore, it can provide the easier, faster, and more economical network infrastructure.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2787-2794
• /
• 2011

A mesh node, a component of a mesh network, is connected with the network by dynamic routing using routing protocol and collects the information of adjacent or connected mesh nodes for its self-management and settings. Also, it relays packets between the mesh nodes and provides AP(Access Point) with its corresponding functions based on IEEE 802.11 a/b/g for clients' access to the network. In this paper, the study focused on the design and performance tests of Wireless Mesh Network(WMN) which is applied to the wireless communication network for the CBTC(Communications Based Train Control) system. The WMN was established on a K-AGT test-line (Kyeongsan city, Gyeongsangbuk-do), and to verify the applicability, its operation and performances are checked by measuring the data throughput, delay latency, quality measurements such as transmission loss, radio interference and path recovery and setup between the on-board and wayside.

• ETRI Journal
• /
• v.31 no.5
• /
• pp.601-603
• /
• 2009

This letter presents a high performance 2.4 GHz two-stage power amplifier (PA) operating in the temperature range from $-30^{\circ}C$ to $+85^{\circ}C$ for IEEE 802.11g, wireless local area network application. It is implemented in InGaP/GaAs hetero-junction bipolar transistor technology and has a bias circuit employing a temperature compensation technique for error vector magnitude (EVM) performance. The technique uses a resistor made with a base layer of HBT. The design improves EVM performance in cold temperatures by increasing current. The implemented PA has a dynamic EVM of less than 4%, a gain of over 26 dB, and a current less than 130 mA below the output power of 19 dBm across the temperature range from $-30^{\circ}C$ to $+85^{\circ}C$.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.3
• /
• pp.174-181
• /
• 2004

In this paper, we review the four receiver architectures and four methods for multi-standard receiver design. Propose reconfigurable RF block can be used for both low-IF and direct conversion architecture. Also, using reconfigurable mixer method, it can be operated at $2{\sim}6$ GHz range for multi-standard receiver. It consists of wideband mixer, filter, and automatic gain control amplifier and to get wide-band operation, $2{\sim}6$ GHz, wide-band mixer use flexible input matching method. Besides, to design multi-standard receiver, LNA bank that support each standard is necessary and it has good performance to compensate the performance of wide-band mixer. Finally, we design and simulate proposed reconfigurable RF block and to prove that it has acceptable performances for various wireless standards, the LNA bank that supports both IEEE 802.11a/b/g and WCDMA is also designed and simulated with it.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.15-18
• /
• 2007

RoF 링크 시스템을 적용한 무선 근거리 통신망(IEEE 802.11b/g)의 중심 주파수 대역인 2.4 GHz에서 저가의 Febry-Perot 레이저 다이오드를 이용한 피드포워드 광송신기를 제작 및 측정 하였다. 제작된 피드포워드 광송신기의 측정 결과는 2.4 GHz에서 주신호의 간격이 10 MHz이고 크기가 -4 dBm인 입력 신호에서 피드포워드 보상기법을 적용하기 전보다 3차 상호 변조 왜곡 신호가 22.9 dB 개선되었다. 제작된 피드포워드 광송신기의 전자소자의 사양을 바탕으로 송신기 집적을 위한 RFIC회로(감쇄기, 증폭기)를 0.18 ${\mu}m$ 공정을 이용하여 설계하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.287-289
• /
• 2009

무선 메쉬 네트워크(WMN, Wireless Mesh Network)에서의 전체적인 성능은 채널의 간섭을 최소화함으로써 개선될 수 있다. 본 논문은 3개의 멀티 채널을 지원하는 IEEE 802.11b/g 기반 WMNs를 위해 제안된 클러스터 기반 채널 할당 기법인 CB-CA(Cluster-Based Channel Assignment)[3] 알고리즘을 멀티 라디오 멀티 채널 WMN 환경에 적합하게 개선시키고자 한다. CB-CA 알고리즘에서는 메쉬 라우터들중에 선택된 클러스터 헤드(CH, Cluster Head) 노드들과 클러스터들 간의 에지 게이트웨이(EG, Edge Gateway) 노드들 간에는 모두 동일 채널을 사용함으로써 채널 스캐닝과 채널 스위칭을 수행하지 않는다. 그러나 이러한 모든 CH들과 EG들 간의 동일 채널의 사용은 많은 노드들에서 채널 간섭을 발생 시키는 문제점이 발생한다. 본 논문에서는 이를 해결하기 위하여 송수신 인터페이스를 구분하고 각 인터페이스에서의 채널을 랜덤하게 설정하고 이를 통신 범위 내에 인접한 이웃 클러스터들에게 알림으로써 서로 간섭이 발생하지 않는 채널들이 설정되도록 한다. 이로써 각 클러스터 간의 채널 간섭을 최소화 할 수 있음과 동시에 다중 인터페이스와 다중 채널을 모두 활용할 수 있어서 QoS를 향상시킬 수있다.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2007.05a
• /
• pp.941-944
• /
• 2007

본 연구에서는 센서 네트웍과 컴퓨터 비전 시스템을 이용한 모바일 센서 네트워크(Mobile Sensor Network) 의 응용에 관한 실험을 수행하였다. 주된 내용으로는 모바일 센서를 탑재한 차량을 이용한 로컬라이제이션(Localization) 과 팀원 인식(Team Identification) 등에 관련된 방법을 포함한다. 본 시스템은 시뮬레이션을 통하여 기획을 하였으며 자체 설계한 하드웨어와 내장형 소프트웨어를 탑재하여 주어진 기능을 수행하도록 하도록 하는 한편, 모바일 센서의 역할을 할 수 있도록 다양한 센서를 장착할 수 있도록 설계되었다. 또한 전자나침반을 이용한 방위각 측정능력, 초음파 센서를 이용한 근거리 장애물 회피 능력, 적외선 발광 다이오드(IR-LED)와 적외선 필터를 씌운 카메라를 이용한 동료의 위치 파악 능력등을 통하여 로컬라이제이션에 도움이 되도록 한다. 통신을 위하여 IEEE 802.11g 프로토콜에 기반을 둔 통신 능력을 가지며 차량간의 통신도 같은 프로토콜을 통하여 이루어지게 된다.

• Electronics and Telecommunications Trends
• /
• v.19 no.3 s.87
• /
• pp.1-11
• /
• 2004

본 고에서는 차세대 이동통신 중 특히 무선전송과 관련한 표준화 및 국내외 기술개발 동향을 살펴보고자 한다. 이를 위해 IMT-2000 규격 표준화를 위해 설립된 3GPP와 3GPP2의 동향을 먼저 살펴보고, 다음으로 북미의 LAN/MAN 표준화 단체인 IEEE 802와, IMT-2000 진화 시스템 및 B3G 시스템 연구를 진행중인 ITU-R WP8F의 활동을 소개한다. 또한 차세대 이동통신 관련 기술에 대한 연구와 표준화 준비를 위해 설립된 포럼들, 즉 유럽 중심의 WWRF, 일본의 mITF, 한국의 GMC 포럼 등의 현황을 살펴보고, 마지막으로 북미, 유럽, 일본 및 중국 등 외국과 국내의 차세대 이동통신 기술개발 동향을 소개한다.