• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.4 no.2
• /
• pp.20-28
• /
• 2008

According to IAEA regulations, a transportation package of radioactive material should perform its intended function of containing the radioactive contents after the drop test, which is one of hypothetical accident conditions. Impact limiters attached to a transport cask absorb the most of impact energy. So, it is appreciated to determine properly the shape, size and material of impact limiters. A material data needed in this determination is a dynamic one. In this study, several materials considered as those of impact limiters were tested by a drop weight facility to acquire dynamic material characteristics data. Impact absorbing volume of the impact limiter was derived mathematically for each drop condition. A size optimization of impact limiter was conducted. The derived impact absorbing volumes were applied as constraints. These volumes should be less than critical volumes generated based on the dynamic material characteristics. The derived procedure to decide the shape of impact limiter can be useful at the preliminary design stage when the transportation package's outline is roughly determined and applied as input value.

• Nuclear Engineering and Technology
• /
• v.41 no.9
• /
• pp.1215-1222
• /
• 2009

The present work pertains to a research program to study Molten Fuel-Coolant Interactions (MFCI), which may occur in a nuclear power plant during a hypothetical severe accident. Dynamics of the hot liquid (melt) droplet and the volatile liquid (coolant) were investigated in the MISTEE (Micro-Interactions in Steam Explosion Experiments) facility by performing well-controlled, externally triggered, single-droplet experiments, using a high-speed visualization system with synchronized digital cinematography and continuous X-ray radiography. The current study is concerned with the MISTEE-NCG test campaign, in which a considerable amount of non-condensable gases (NCG) are present in the film that enfolds the molten droplet. The SHARP images for the MISTEE-NCG tests were analyzed and special attention was given to the morphology (aspect ratio) and dynamics of the air/ vapor bubble, as well as the melt drop preconditioning. Energetics of the vapor explosion (conversion ratio) were also evaluated. The MISTEE-NCG tests showed two main aspects when compared to the MISTEE test series (without entrapped air). First, analysis showed that the melt preconditioning still strongly depends on the coolant subcooling. Second, in respect to the energetics, the tests consistently showed a reduced conversion ratio compared to that of the MISTEE test series.

• Journal of Korean Academy of Fundamentals of Nursing
• /
• v.25 no.4
• /
• pp.269-281
• /
• 2018

Purpose: The purpose of this study was to build a model to predict the fall prevention behavior of nurses in small and medium sized hospitals. Methods: Participants were 382 nurses from 13 hospitals who responded to the structured self-reported questionnaire. The research model was based on previous study of fall prevention, theory of planned behavior, and the health belief model. Results: The modified model generally showed higher levels than recommended level of model fit indices and acceptable explanation. Of 17 hypothetical paths, 14 were supported. Predicting variables explained 51.6% of fall prevention behavior. The fall prevention behavior of nurses showed a direct influence of fall prevention expectations, fall prevent threats, perceived behavioral control for fall prevention, and intention to prevent falls and an indirect of influence of patient safety culture, attitude toward fall prevention, and the subjective norm. Conclusion: Findings show a need to identify a range of barrier factors to increase the benefits of fall prevention behavior and enhance the perceived control of fall prevention so that nurses will be able to promote fall prevention behavior in hospitals. Also, it is critical to increase awareness of patient safety culture among nurses.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.117-129
• /
• 2022

The downward discharge of the molten fuel to the lower structure of the fuel assembly could increase of the pressure drop and degrade of coolability of the assembly. To analyze the phenomena, experiments for the generation of the debris bed were conducted as LOF-DT series. Based on the debris bed in the LOF-DT, pressure drop experiment was conducted with intact and blocked component. Parametric study on the pressure drop was conducted by CFD. The LOF-DT experiments were conducted for the position and porosity of the debris bed. 85% of the debris were sedimented in the lower reflector, and 15% were in the nose piece, approximately. Porosity of the debris bed were about 0.7 and 0.85 in the lower reflector and nose piece, respectively. Pressure drop increased significantly with debris bed, especially in the lower reflector. More than 120 time of the pressure drop increased in the lower reflector, while only 10% increased in the nose piece. According to the parametric study, mass of the debris was the most important for pressure drop. The lower discharge phenomena could have a significant effect to the total pressure drop of the fuel assembly, approximately 10.8 times for the base case.

• Nuclear Engineering and Technology
• /
• v.56 no.3
• /
• pp.846-854
• /
• 2024

FEMAXI-ATF is being developed for fuel performance modeling of SiC cladded UO2 fuel with focuses on modeling pellet-cladding mechanical interactions (PCMI). The code considers probability distributions of mechanical strengths of monolithic SiC (mSiC) and SiC fiber reinforced SiC matrix composite (SiC/SiC), while it models pseudo-ductility of SiC/SiC and propagation of cladding failures across the wall thickness direction in deterministic manner without explicitly modeling cracks based on finite element method in one-dimensional geometry. Some hypothetical BWR power ramp conditions were used to test sensitivities of different model parameters on the analyzed PCMI behavior. The results showed that propagation of the cladding failure could be modeled by appropriately reducing modulus of elasticities of the failed wall element, so that the mechanical load of the failed element could be re-distributed to other intact elements. The probability threshold for determination of the wall element failure did not have large influence on the predicted power at failure when the threshold was varied between 25 % and 75 %. The current study is still limited with respect to mechanistic modeling of SiC failure as it only models the propagation of the cladding wall element failure across the homogeneous continuum wall without considering generations and propagations of cracks.

• Journal of Radiation Protection and Research
• /
• v.38 no.2
• /
• pp.60-67
• /
• 2013

A diffusion coefficient is an important parameter in the prediction of atmospheric dispersion using a Gaussian plume model, and its modelling approach varies. In this study, dispersion coefficients recommended by the U. S. Nuclear Regulatory Commission's (U. S. NRC's) regulatory guide and the Canadian Nuclear Safety Commission's (CNSC's) regulatory guide, and used in probabilistic accident consequence analysis codes MACCS and MACCS2 have been investigated. Based on the atmospheric dispersion model for a hypothetical accidental release recommended by the U. S. NRC, its influence to atmospheric dispersion factor was discussed. It was found that diffusion coefficients are basically predicted from a Pasquill- Gifford curve, but various curve fitting equations are recommended or used. A lateral dispersion coefficient is corrected with consideration for the additional spread due to plume meandering in all models, however its modelling approach showed a distinctive difference. Moreover, a vertical dispersion coefficient is corrected with consideration for the additional plume spread due to surface roughness in all models, except for the U. S. NRC's recommendation. For a specified surface roughness, the atmospheric dispersion factors showed differences up to approximately 4 times depending on the modelling approach of a dispersion coefficient. For the same model, the atmospheric dispersion factors showed differences by 2 to 3 times depending on surface roughness.

• Journal of Radiation Protection and Research
• /
• v.36 no.3
• /
• pp.148-153
• /
• 2011

EMRAS-2 (Environmental Modelling for RAdiation Safety, Phase 2) is an international comparison program, which is organized by the International Atomic Energy Agency (IAEA), in order to harmonize the modelling of radionuclide behavior in the environment. To do so, the urban contamination working group within EMRAS-2 has designed the hypothetical scenarios for a specified urban area. In this study, the importance of contaminated surfaces composing an urban environment was analyzed in terms of dose rate using METRO-K, which has been developed to take a Korean urban environment into account. The contribution of contaminated surfaces to exposure dose rate showed distinctly a great difference as a function of specified locations and time following a hypothetical event. Moreover, it showed a distinct difference according to the existence of precipitation, and its intensity. Therefore, if an urban area is contaminated radioactively by any unexpected incidents such as an accident of nuclear power plants or an explosion of radioactive dispersion devices (RDDs), appropriate measures should be taken with consideration of the type of surface composing the contaminated environment in order to minimize not only radiation-induced health detriment but also economic and social impacts.

• Journal of Radiation Protection and Research
• /
• v.9 no.1
• /
• pp.26-32
• /
• 1984

The exposure doses by the radioactive gaseous effluents from nuclear power plants are investigated in the two cases of normal operation and hypothetical accident. Gaussian equation is adapted in the normal operation as the diffusion model of effluents for long period, which uses annual average meteorological data. But the real time models have been used in the case of accidents which analyze the changes of wind direction and speed. In this study the annual exposure doses by the normal operation of Kori unit 1 during $1977{\sim}1982$ were calculated on the basis of the atmospheric diffusion factor by the Gaussian straight line model. And the image processing technique was suggested as the effective method through the wind tunnel experiments to get the characteristic value of atmospheric diffusion coefficient required especially in the accidents of nuclear power plants.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.3
• /
• pp.245-253
• /
• 2006

A test of the 1/3 scale model was conducted to verify the tip-over analysis of a dry. concrete storage cask under a hypothetical accident condition. The tip-over analysis was executed using the velocity at each point as the initial conditions of the model just before the impact. The initial velocity was determined from the initial angular velocity, which would make the equivalent kinetic energy to the potential energy. To confirm the structural integrity of the canister, the visual testing and the non-detective testings such as Liquid Penetrant testing and Ultrasonic Testing were conducted. The lid of a storage cask was plastically deformed near the impact point. The structural integrity of storage cask was maintained. To verify the tip-over analysis the strains and the accelerations acquired by the tip-over test were compared with those by the analyses. The results of the analysis were larger than the test results about two times.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.1
• /
• pp.9-16
• /
• 2009

Transport package for radioactive material should be structurally safe under puncture drop condition and its safety should be verified by test and numerical analysis. Most finite element analyses for puncture drop have been performed without modeling the impact limiter since failure is occurred in the materials of the impact limiter. This paper presents a new modeling methodology, where an element is eroded in case that the material's failure criteria are reached at the element's integration point, to investigate the effect of the impact limiter in the puncture process. The effectiveness of the proposed scheme is shown through the puncture drop analysis of hotcell transport cask, which is under design in KAERI. The results show that about 80 percent of the total impact energy is absorbed due to the deformation of impact limiter. Using the present method the puncture drop can be analyzed more accurately, but it would give conservative results compared to the actual test condition.