• 한국추진공학회지
• /
• 제14권2호
• /
• pp.71-79
• /
• 2010

극초음속 비행체의 속도증가와 엔진효율의 향상으로 비행체와 엔진의 열적부하가 증가하게 되었다. 극초음속 영역에서 공기흐름의 온도는 매우 높기 때문에 공냉방식을 이용한 냉각이 불가능하므로, 비행체 연료를 주 냉각제로써 이용하는 것은 필수적이다. 흡열연료(Endothermic fuels)는 열분해 또는 촉매분해와 같은 흡열반응(Endothermic reaction)을 통해 열을 흡수하는 액체 탄화수소 비행체 연료이다. 흡열반응은 촉매를 이용하여 전환율과 생성물 분포를 변화시킴으로써 개선될 수 있다. 고온의 액체 탄화수소는 코킹 생성을 유발하여 열교환기의 효율을 저하시키고 촉매 비활성을 촉진시킬 수 있기 때문에, 흡열연료의 흡열능력은 코킹생성(Coke formation)이 발생하기 전까지의 온도로 제한한다. 본 연구 에서는 흡열연료를 적용한 주요 냉각기술동향과 흡열연료의 특성이 기술되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.136-140
• /
• 2005

일차원 ZND 데토네이션 구조 해석 모델의 연장선상에서 경사 충격파와 경사 데토네이션 파에 대하여 Rankine-Hugoniot 관계식과 반응속도를 연계한 이차원 경사 데토네이션 파의 구조해석 모델을 제시하였다. 이에 기반을 두어 삼중점, 횡단 충격파 및 셀 구조를 포함하는 경사 데토네이션 파의 비정상 상세 구조를 조사하기 위한 이차원 유체역학 해석을 수행하였다. 전산 유체 해석 결과는 경사 데토네이션 파의 상세구조에 대한 깊이 있는 이해를 제공하며, 해석 모델은 경사 데토네이션 파를 연소 메커니즘으로 이용하는 극초음속 추진기관의 통합 설계도구로 이용될 수 있을 것이다.

• 한국추진공학회지
• /
• 제20권5호
• /
• pp.90-98
• /
• 2016

극초음속 공기 흡입 추진기관의 지상 시험 시 추진기관의 고속 비행 조건을 모의하기 위해 고온 공기를 공급할 수 있는 고온 공기 가열기가 필요하다. 본 논문에서는 다양한 고온 가열기들을 조사하여 유형별로 정리하고, 장단점을 비교하였다. 가열기는 크게 유동장 내 연소 가열기, 아크 가열기, 축열식 가열기, 열교환식 가열기 4종류로 분류할 수 있었으며, 각각의 장단점이 다양하므로 목적에 맞게 가열기를 선정하여야 한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.34-40
• /
• 2004

Two different type scramjet models with side-wall compression and top-wall compression inlets have been tested in HPTF (Hypersonic Propulsion Test Facility) under the experimental conditions of Mach number 5.8, total temperature 1700K, total pressure 4.5㎫ and mass flow rate 3.5kg/s. The liquid kerosene was used as main fuel for the scramjets. In order to get fast ignition in the combustor, a small amount of hydrogen was used as a pilot. A strut with alternative tail was employed for increasing the compression ratio and for mixing enhancement in the side-wall compression case. Recessed cavities were used as a flameholder for combustion stability. The combustion efficiency was estimated by one dimensional theory. The uniformity of the facility nozzle flow was verified by a scanning pitot rake. The experimental results showed that the kerosene fuel was successfully ignited and stable combustion was achieved for both scramjet models. However the thrusts were still less than the model drags due to the low combustion efficiencies.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.310-319
• /
• 2017

충격파 시험장치를 이용하여 추력을 측정하는 방법을 소개하였다. 충격파 시험장치를 이용하여 엔진의 추력을 측정하기 위해서는 일반적인 엔진시험 시설에서 추력을 측정하기 위해 사용하는 밸런스가 힘의 평형상태에 도달하지 못하기 때문에 응력파 힘 밸런스(Stress Wave Force Balance) 방법을 이용하여 측정한다. 본 논문에서는 모델 힘 밸런스(force balance)에 대해 충격하중을 주고 유한요소법(FEM)으로 변형률을 계산하였다. 충격하중과 변형률의 관계를 역합성곱(de-convolution)하여 천이함수를 도출하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.346-357
• /
• 2008

Endothermic fuels are known as a probable fuel for hypersonic atmospheric flight vehicles and advanced propulsion systems, as well as cryogenic fuels. Especially, from the standpoint of the advanced regenerative cooling use, they are quite useful as a coolant fuel because of their large heat sink due to their chemical decompositions; so-called endothermic cooling effect. However, no heat transfer equations have been proposed taking into account such endothermic reactive behaviors concretely. This paper describes an analytical method for evaluation of the heat transfer rates between endothermic reacting coolant fuel and coolant-side wall in the regenerative cooling passages. Heat transfer mechanism is indicated based on a classical transport-phenomenological approach. A new relational expression of Nusselt number ratio for forcedconvective heat transfer with such endothermic reactions is also proposed by theoretical approaches using some classical hypotheses. Its applicability is assessed provisionally by comparison with confirmed results of heated tube tests for supercritical JP-7 fuel carried out at NASA Lewis Research Center, using its heat sink characteristics evaluated by United Technologies Research Center(UTRC). As a result, it has been suggested that the proposed relational equation is applicable to the evaluation of enhancement of Nusselt numbers due to such reactions in developed turbulent flows such as in the regenerative cooling passages.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.671-686
• /
• 2004

The shock-induced combustion ramjet (shcramjet) is a hypersonic airbreathing propulsion concept which over-comes the drawbacks of the long, massive combustors present in the scramjet by using a standing oblique detonation wave (a coupled shock-combustion front) as a means of nearly instantaneous heat addition. A novel shcramjet combustor design that makes use of wedge-shaped flameholders to avoid detonation wave-wall interactions is proposed and analyzed with computational fluid dynamics (CFD) simulations in this study. The laminar, two-dimensional Navier-Stokes equations coupled with a non-equilibrium hydrogen-air combustion model based on chemical kinetics are used to represent the physical system. The equations are solved with the WARP (window-allocatable resolver for propulsion) CFD code (see: Parent, B. and Sislian, J. P., “The Use of Domain Decomposition in Accelerating the Convergence of Quasihyperbolic Systems”, J. of Comp. Physics, Vol. 179, No. 1,2002, pages 140-169). The solver was validated with experimental results found in the literature. A series of steady-state numerical simulations was conducted using WARP and it was deter-mined by means of thrust potential calculations that this combustor design is a viable one for shcramjet propulsion: assuming a shcramjet flight Mach number of twelve at an altitude of 36,000 m, the geometrical dimensions used for the combustor give rise to an operational range for combustor inlet Mach numbers between six and eight. Different shcramjet flight Mach numbers would require different combustor dimensions and hence a variable geometry system in or-der to be viable.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.671-679
• /
• 2008

The effect of Pre-cooled Turbojet Engine installation and nozzle exhaust jet on Hypersonic Turbojet EXperimental aircraft(HYTEX aircraft) were investigated by three-dimensional numerical analyses to obtain aerodynamic characteristics of the aircraft during its in-flight condition. First, simulations of wind tunnel experiment using small scale model of the aircraft with and without the rectangular duct reproducing engine was performed at M=5.1 condition in order to validate the calculation code. Here, good agreements with experimental data were obtained regarding centerline wall pressures on the aircraft and aerodynamic coefficients of forces and moments acting on the aircraft. Next, full scale integrated analysis of the aircraft and the engine were conducted for flight Mach numbers of M=5.0, 4.0, 3.5, 3.0, and 2.0. Increasing the angle of attack $\alpha$ of the aircraft in M=5.0 flight increased the mass flow rate of the air captured at the intake due to pre-compression effect of the nose shockwave, also increasing the thrust obtained at the engine plug nozzle. Sufficient thrust for acceleration were obtained at $\alpha=3$ and 5 degrees. Increase of flight Mach number at $\alpha=0$ degrees resulted in decrease of mass flow rate captured at the engine intake, and thus decrease in thrust at the nozzle. The thrust was sufficient for acceleration at M=3.5 and lower cases. Lift force on the aircraft was increased by the integration of engine on the aircraft for all varying angles of attack or flight Mach numbers. However, the slope of lift increase when increasing flight Mach number showed decrease as flight Mach number reach to M=5.0, due to the separation shockwave at the upper surface of the aircraft. Pitch moment of the aircraft was not affected by the installation of the engines for all angles of attack at M=5.0 condition. In low Mach number cases at $\alpha=0$ degrees, installation of the engines increased the pitch moment compared to no engine configuration. Installation of the engines increased the frictional drag on the aircraft, and its percentage to the total drag ranged between 30-50% for varying angle of attack in M=5.0 flight.

• 한국추진공학회지
• /
• 제19권6호
• /
• pp.33-41
• /
• 2015

로켓 기반 복합 사이클 엔진의 구성 요소로서 큰 후향 계단을 가진 이중 모드 램젯 엔진의 축소 모델을 설계하였다. 로켓 기반 복합 사이클 엔진에 적용하기 위해 설계 단계에서 고려하여야 하는 인자를 도출하였고 이 설계 인자에 대한 설계 방법을 정립하였다. 이러한 방법을 통하여 설계한 모델에 대하여 전산유체해석과 공력 시험을 수행함으로써 설계 검증을 일부 수행하고 큰 후향 계단을 가진 이중 모드 램젯 엔진의 유동 특성을 파악하였으며 이 연구에서 정립한 주요 설계 인자에 대한 설계 방법이 타당함을 확인할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2000년도 제14회 학술강연논문집
• /
• pp.8-8
• /
• 2000

In this paper are presented main power and gasdynamic characteristics of C-l6VK hypersonic test cell of Research Test Center of CIAM. Gasdynamic adjustment of the C-l6VK test cell was carried out with the working section constructed on scheme of Ramjet/scramjet test in free stream. Gasdynamic adjustment was conducted stage by stage in tile following sequence. First, check and preparation of all technical systems and checking measuring system. Than determination of the characteristics of test cell on cold (without the heating of air at entrance) regime and determination of the characteristics of test cell on regimes with the heating of air. Finally determination of tile characteristics of test cell with the loading of the working part by object. On tile final stage of gasdynamic adjustment two experiments with tile axisymmetric Scramjet model loaded into the working part of test cell were conducted. The first experiment was conducted with the purpose of determination of flow parameters with the object leaded into the working part and verification of experiment cyclogram. The second experiment was conducted with injection of hydrogen into the combustion chamber of object, that is tile conditions on test cell simulated Scramjet flight Mach number M = 6. Such methodology of gasdynamic adjustment allows to determine influence of experimental object on flow parameters in the working part at different conditions of experiment (with the burning in combustion chamber of object and without the homing), and also to compare flow characteristics in the object duct.