• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.5
• /
• pp.621-629
• /
• 2007

This study intends to investigate the characteristics of the foul smell of sewer pipes near large apartment complexes as complaints about offensive odors have drastically increased in urban residential areas. Targeting apartments where people actually complained about foul orders, the study result revealed that components in the smell of the water-purifier tank of the target apartment were very similar to those of sewage treatment plants and night soil treatment plants. Measuring components of odors inside the management layer of tank showed that the concentration of hydrogen sulfide was 10ppm, which is approximately 160 times the safety standard of 0.06ppm; the concentration of mercaptan was 0.9ppm, which is about 220 times the safety standard of 0.004ppm. The source materials of foul odors were discharged outside through ducts, and those households living near outlets producing bad smell complain that it gets worse depending on the air pressure or wind direction and strength, and they could not even open windows. As well, these source materials were transferred by discharge pumps to public sewer pipes outside the apartment complex. While discharge pumps starts operating, they remain on the sewer pipe and then begin to spread over to roads through small openings of manholes on the road. Then, the smell offends passers-by and residents near the road, leading to a lot of complaints. The study results suggest that, among the sources of foul odors in sewer pipes of residential areas, especially those from the water-purifier tank of large apartments, hydrogen sulfide should be the main target for follow-up treatment.

• Journal of the Korean Society of Safety
• /
• v.24 no.3
• /
• pp.54-58
• /
• 2009

A substitute energy development has been required due to the exhaust of the fossil fuel and an environmental problem. Consequently, possible technologies producing hydrogen from water that does not release carbon is a very promising technology. Also, Iodine-Sulfur(IS) thermochemical water decomposition is one of the promising processes that are used to produce hydrogen efficiently using the high temperature gas-cooled reactor(HTGR) as an energy source that is possible to supply heat over 900$^{\circ}C$. In this study, to make a initiating events identification for the IS process, Master Logic Diagram(MLD) is used and 9 initiating events that cause a leakage of the chemical material are identified. Also, 6 events are identified among 9 initiating events above and are quantified using event tree.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.264-264
• /
• 2012

As an environment-friendly alternative energy resource, ethanol may be used to obtain hydrogen, a clean energy source. Thus, studies on catalytic reactions involving ethanol have been studied to understand the underlying principles in the reaction mechanism using various oxide-supported catalysts. Among them, Au-based catalysts have shown a superior activity in producing hydrogen gas. In the present study, Au/$TiO_2$ catalysts were prepared by deposition-precipitation method to understand their catalytic activities toward ethanol and acetaldehyde with increasing gold loading, especially at the very low Au loading regime. A commercially available $TiO_2$ (Degussa P-25) was employed and the Au loading was varied to 0, 0.1, 0.5, and 1.0 wt% respectively. The catalysts showed characteristic x-ray diffraction (XRD) features at $2{\theta}=78.5^{\circ}$ that could be assigned to the presence of gold nanoparticles. Its reactivity measurements were performed under a constant flow of ethanol and acetaldehyde at a flow rate of ${\sim}0.6{\mu}mol/sec$ and the substrate temperature was slowly raised at a rate of 0.2 K/sec. We observed that the overall reactivity of the catalysts increased with increasing Au loading along with selectivity favoring dehydrogenation to product hydrogen gas. In addition, we disclosed various reaction channels involving competitive reaction paths such as dehydrogenation, dehydration, and condensation. In addition, subsequent reactions of acetaldehyde obtained from dehydrogenation of ethanol, were found to occur and produce butene, crotonaldehyde, furan, and benzene. Based on the results, we proposed overall reaction pathways of such reaction channels.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.29.1-29.1
• /
• 2009

Fabrication of good quality P-type GaN remained as a challenge for many years which hindered the III-V nitrides from yielding visible light emitting devices. Firstly Amano et al succeeded in obtaining P-type GaN films using Mg doping and post Low Energy Electron Beam Irradiation (LEEBI) treatment. However only few region of the P-GaN was activated by LEEBI treatment. Later Nakamura et al succeeded in producing good quality P-GaN by thermal annealing method in which the as deposited P-GaN samples were annealed in N2 ambient at temperatures above $600^{\circ}C$. The carrier concentration of N type and P-type GaN differs by one order which have a major effect in AlGaN based deep UV-LED fabrication. So increasing the P-type GaN concentration becomes necessary. In this study we have proposed a novel method of activating P-type GaN by electrochemical potentiostatic method. Hydrogen bond in the Mg-H complexes of the P-type GaN is removed by electrochemical reaction using KOH solution as an electrolyte solution. Full structure LED sample grown by MOCVD serves as anode and platinum electrode serves as cathode. Experiments are performed by varying KOH concentration, process time and applied voltage. Secondary Ion Mass Spectroscopy (SIMS) analysis is performed to determine the hydrogen concentration in the P-GaN sample activated by annealing and electrochemical method. Results suggest that the hydrogen concentration is lesser in P-GaN sample activated by electrochemical method than conventional annealing method. The output power of the LED is also enhanced for full structure samples with electrochemical activated P-GaN. Thus we propose an efficient method for P-GaN activation by electrochemical reaction. 30% improvement in light output is obtained by electrochemical activation method.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.1-6
• /
• 2019

Recent industrialization has led to a high demand for the use of fossil fuels. Therefore, the need for producing hydrogen and its utilization is essential for a sustainable society. For an eco-friendly future technology, photoelectrochemical water splitting using solar energy has proven promising amongst many other candidates. With this technique, semiconductors can be used as photocatalysts to generate electrons by light absorption, resulting in the reduction of hydrogen ions. The photocatalysts must be chemically stable, economically inexpensive and be able to utilize a wide range of light. From this perspective, cuprous oxide($Cu_2O$) is a promising p-type semiconductor because of its appropriate band gap. However, a major hindrance to the use of $Cu_2O$ is its instability at the potential in which hydrogen ion is reduced. In this study, gold is used as a bottom electrode during electrodeposition to obtain a preferential growth along the (111) plane of $Cu_2O$ while imperfections of the $Cu_2O$ thin films are removed. This study investigates the photoelectrochemical properties of $Cu_2O$. However, severe photo-induced corrosion impedes the use of $Cu_2O$ as a photoelectrode. Two candidates, $TiO_2$ and $SnO_2$, are selected for the passivation layer on $Cu_2O$ by by considering the Pourbaix-diagram. $TiO_2$ and $SnO_2$ passivation layers are deposited by atomic layer deposition(ALD) and a sputtering process, respectively. The investigation of the photoelectrochemical properties confirmed that $SnO_2$ is a good passivation layer for $Cu_2O$.

• The Korean Journal of Physiology and Pharmacology
• /
• v.25 no.6
• /
• pp.593-601
• /
• 2021

Primary cilia on kidney tubular cells play crucial roles in maintaining structure and physiological function. Emerging evidence indicates that the absence of primary cilia, and their length, are associated with kidney diseases. The length of primary cilia in kidney tubular epithelial cells depends, at least in part, on oxidative stress and extracellular signal-regulated kinase 1/2 (ERK) activation. Hydrogen sulfide (H₂S) is involved in antioxidant systems and the ERK signaling pathway. Therefore, in this study, we investigated the role of H₂S in primary cilia elongation and the downstream pathway. In cultured Madin-Darby Canine Kidney cells, the length of primary cilia gradually increased up to 4 days after the cells were grown to confluent monolayers. In addition, the expression of H₂S-producing enzyme increased concomitantly with primary cilia length. Treatment with NaHS, an exogenous H₂S donor, accelerated the elongation of primary cilia whereas DL-propargylglycine (a cystathionine γ-lyase inhibitor) and hydroxylamine (a cystathionine-β-synthase inhibitor) delayed their elongation. NaHS treatment increased ERK activation and Sec10 and Arl13b protein expression, both of which are involved in cilia formation and elongation. Treatment with U0126, an ERK inhibitor, delayed elongation of primary cilia and blocked the effect of NaHS-mediated primary cilia elongation and Sec10 and Arl13b upregulation. Finally, we also found that H₂S accelerated primary cilia elongation after ischemic kidney injury. These results indicate that H₂S lengthens primary cilia through ERK activation and a consequent increase in Sec10 and Arl13b expression, suggesting that H₂S and its downstream targets could be novel molecular targets for regulating primary cilia.

• Journal of Microbiology and Biotechnology
• /
• v.11 no.4
• /
• pp.558-563
• /
• 2001

A new alkalophilic strain of Bacillus pumilus JB¬05 producing bleach-stable and halo-tolerant alkaline protease was isolated from cement industry effluents in Karnataka, India. The effects of carbon and nitrogen sources on protease production by this alkalophilic strain were observed after a 30-h incubation. A high level of alkaline protease activity was obtained in the presence of starch as the carbon and peptone as the nitrogen sources. The partially purified enzyme showed an optimum temperature and pH activity at $58^{\circ}C$ and 10.5, respectively. The enzyme was completely inhibited by PMSF (95.0%) indicating it as a serine protease. It is bleach-stable as it retained 35% original activity in the presence of 10% (v/v) hydrogen peroxide at $30^{\circ}$C after 2 h and is halo-tolerant as it retained 70% original activity in the presence of 2.5 M sodium chloride at $30^{\circ}C$ after 2 h incubation.

• Journal of Surface Science and Engineering
• /
• v.33 no.2
• /
• pp.69-76
• /
• 2000

The rf plasma chemical vapor deposition is a common method employed for diamond or amorphous carbon deposition. Diamond possesses the strongest bonding, as exemplified by a number of unique properties-extraordinary hardness, high thermal conductivity, and a high melting tempera tore. Therefore, it is very important to investigate the synthesis of semiconducting diamond and its use as semiconductor devices. An inductively coupled rf plasma CVD system for producing amorphous carbon films were developed. Uniform temperature and concentration profiles are requisites for the deposition of high quality large-area films. The system consists of rf matching network, deposition chamber, pumping lines for gas system. Gas mixtures with methane, and hydrogen have been used and Si (100) wafers used as a substrate. Amorphous carbon films were deposited with methane concentration of 1.5% at the process pressure of S torr~20 torr, and process temperature of about $750^{\circ}C$. The nucleation and growth of the amorphous carbon films have been characterized by several methods such as SEM and XRD.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.1
• /
• pp.40-48
• /
• 2010

The purpose of the research is to develop the high performance solar chemical reactor for producing hydrogen using steam reforming reaction of methane. A specific shape chemical reactor is suggested : spiral type reactor. The reactor is installed on the dish-type solar thermal system of Inha University. The temperatures, $CH_4$ conversion rates, and Hz proportion are measured. At specific condition, $CH_4$ conversion rates of the spiral type reactor are about 91%, and Hz proportion are about 66%. The spiral type reactor gives reasonably good performance without any problems caused by highly concentrated solar radiation.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.11a
• /
• pp.10-10
• /
• 2000

Mechanical alloying (MA) is a powder metallurgy processing technique involving cold welding, fracturing, and rewelding of powder particles in a high-energy ball mill. This has now become an established commercial technique in producing oxide dispersion strengthened (ODS) nickel- and iron-based materials. The technique of MA is also capable of synthesizing non-equilibrium phases such as supersaturated solid solutions, metastable crystalline and quasicrystalline intermetallic phases, nanostructures, and amorphous alloys. In this respect, the capabilities of MA are similar to those of another important non-equilibrium processing technique, viz, rapid quenching of metallic melts. however, the science of MA is being investigated only during the past ten years or so. The technique of mechanochemistry, on the other hand, has had a long history and the materials produced this way have found a number of technological applications, e.g., in areas such as hydrogen storage materials, heaters, gas absorber, fertilizers. catalysts, cosmetics, and waste management. The present talk will concentrate on the basic mechanisms of formation of non-equilibrium phases by the technique of MA and these aspects will be compared with those of rapid quenching of metallic melts. Additionally, the variety of technological applications of mechanically alloyed products will be highlighted.